Difference factor for rfid ' s non-dry glue label price and bulk quotation explanation
The price of the RFID non-dry glue label is ranging from a few cents to several dollars, and the difference is mainly from five puzzles of chips, antennas, faceware, wrapping processes and order quantities.
Cost: Five components of unit price
Also known as the "RFID non-dry glue label" the cost of different configurations may be more than ten times different.
Chip: programme difference between imports and national production
The common programme is one of the most expensive ones in a label. The imported chip (e.g. Alien Higgs, Impinj Monza series) is better marked for stability and consistency, with single chips usually priced at 0.3-1 meta-zones; national chips (e.g., a program for manufacturers like twilight electronics) are more competitive, with singles in the range of 0.05 to 0.3 dollars. The difference is followed by protocol compatibility, good mass output, and performance under different readers.
When we do programs for clients, we usually identify their existing type and brand of readers, then push the chip programme to avoid the embarrassment of "cheese without reading."
Antenna: cost gradient for three processes
An antenna determines the signal reception capacity of labels, with three main processes:
- Aluminium graft.(a) High accuracy, stable performance and the highest cost of single labels for scenarios that are suitable for high dyslexia;
- Copper wires bypass antennas: Medium cost, appropriate for medium distance identification;
- Ink-transmitting antennaMinimum cost, suitable for a large, low-cost, less distance-required scenario such as one-time logistics sealing.
Face and cover: determines how long it takes.
The average copper sheet of paper costs the least, but it is resistant to tearing, heat, and damp-resistant; PET, PP synthetic paper is slightly more expensive and more resilient to scratch; when you need to put on a metal surface, you need an anti-metallic suction material that will allow the unit price to float from 0.2 to 0.5. If labels are to be placed in a high wet, low temperature or oily environment, the choice of the containment process (tip, laminate, moth, moth) has a direct impact on the unit price and on the life of the service.
Effect: What's the difference?
The price is not good, the price is not bad. The key is to see if you need the power to change the price.
Read-and-write distance and consistency
Under the same size label, imported chips are bound to carving antennas, and UHF frequency is usually able to read 8-12 meters with steady reading, and group reading speed is more stable; national chips add printing antennas, which can be read at distances of 3-6 metres, with leakage during group reading. Logistics warehouse inspections, streaming lines tracking such scenes often require remote group reading; doorshop security, ticket write-off scenes, few centimetres to one or two metres of reading distance, do not have to pay a premium for overdrafting performance.
Environmental adaptation and longevity
The outdoor asset label, if it uses just plain copper paper, may drop chips in six months, signal decay. We saw a cold-chain customer who initially took the low price option, and then went through the bulk after three months in an environment - 18 °C, and then went back to work, at a higher cost. The environment is complex, with life requirements for scenes, and we suggest that budgets be added to the facebook and cover.
Batch size: Start-up is the first lever for unit prices
The unit price of the RFID label is very sensitive to the mass, because the cost of chips, modulations, and humans are "starting" at all three.
- 1,000–5,000 tags: sample runs, at the highest unit price, commonly used to validate a design;
- 10,000-100,000 units: Small pilot run, with a unit price 20%-40% below sample production;
- Over 500,000 pieces: Large-scale stable orders, with a further 15% to 30% unit price.
This is clearly stated in Shanghai's proposal-making policy, which avoids the other party's focus on unit prices while ignoring the order and delivery. The bulk offer usually involves pre-printing fees, chip pre-coding, data writing services etc., which are best listed once in a while when asking for proposals, saving later additions.
Applicable scene: what needs to be configured
Select RFID, which is not a dry glue label, essentially balances "performance, cost, use." The following common scenarios can be used as a reference for configuration:
- Warehouse Tray/Caler Management: 5-10 m reading distance, mostly group reading, with a recommendation for imported or medium-high end nationally produced chips + etching/aluminium antenna;
- Retail labels for clothingSmall size, cost-sensitive, reading distance of 1-3 m, and national chips + print antennas are a combination of high value for money;
- Tickets/forgery/retroactive(a) Need for transfer and forgery-proof printing, usually with NFC or UHF matching to special face materials, with high unit prices but high impact on experience;
- Metal asset tracking: The metal-resistant label must be used, and the unit price will be 30% - 80% more than the general amount, which cannot be replaced with a cheap amount.
There is no need to pay for over-configuration if the scenes are not rigid to read distance, durability and safety.
A few holes that are common to the offer.
A few times, RFID buyers find that the price offers contain a lot of traps.
- Just look at unit prices and not at configurations.: The "0.2 yuan/filtration" on the quotation appears cheap, but the actual landing price may double if it is not written without data, without face and without a modulation;
- Ignore the order and date: Some options to start a chip order of more than 50,000 chips, and small batches are not available;
- The chip compatibility is not confirmed.: The mismatch between the label and the reader agreement is a common reason for return to work, with the supplier being informed of the type of reader before the quotation;
- There's a difference between testing samples and big stuff.: Some suppliers send samples with imported chips, and the official quantities are converted to national production, which is an occasional situation in the industry where large goods are recommended for a stub test.
The key to avoiding these pits is to give the demand (chip schemes, antennas, face, dimensions, reading distance, reader type, batch, delivery, environment) once to the supplier, and to get the other side to present a full offer instead of a single blank label.
Proposals for action
Before you get the RFID non-dry tape label offer, you answer three questions: what's the scene, how much is the amount of the existing reader? These three questions are clear, and the offers are comparable. The same specification, the same volume, is more spectrometric than a single offer for two or three suppliers, and the larger the lot, the more it is worth writing in front of the print, the code, the sample, the more it is written in the contract.

Ms. Lei
Mr. Pang