How does the fixed asset system work? Daily operating processes and key documents are analysed.
RFID Knowledge

How does the fixed asset system work? Daily operating processes and key documents are analysed.

PublishedShanghai Zejie Smart Technology Co., Ltd.

The new accountant, the first time he recorded his assets, he got stuck.

Last year, a customer who made furniture, the new accountant, first came into contact with the fixed asset system. Turned on the interface, the field "Asset Class" "Use Age" "Remain Value Rate" was filled in three wrong times, and finally ran out of monthly depreciation that went against the Treasury Director's manual calculations, so he had to delete the whole series of cards and re-establish it.

A fixed asset system has four basic jobs: create asset records, post monthly depreciation, process change documents, and generate reports. Experienced users can record transactions in a little over ten minutes a day; inexperienced users can spend until midnight reconciling at month-end. The key is routing documents correctly at each step. Below is the workflow in operational order.

Asset card: Good set, it's all over the back.

Asset cards (also known as fixed asset master files) are the source of all data in the system, which corresponds to "id ID" for each device and piece of furniture.

The entry path is usually added from the Asset Management Card Management, and the system automatically generates asset numbers after it has been saved. If a group of similar devices buys them at the same time, the "volume-building card" feature is used faster, with dozens of copies recorded at a time.

There's a pit where you can step on it: many companies also put low-value, low-value, low-value, low-value, low-value, low-value, low-value, low-value, low-value, low-cost items (e.g. office chairs, file cabinets) into the system as fixed assets, so they expand to thousands of cards and go half a day in light. In fact, for less than $5,000 per unit, for less than one year, the system allows "low-value, easy-to-use" or "switch material" to be taken off the fixed-asset system.

Monthly depreciation: System auto-run, but trigger condition is set

Depreciation is the most frequent feature in a fixed asset system, with most systems supporting automatic monthly drawing.

Check the card status first.

There's a "use status" field in the system, divided into "no use" without "no need to "in." Only assets in "utilise" are depreciated. This field is checked at the beginning of each month, especially for cross-sectional transfers, equipment storage scenes, and the state is not depreciated, otherwise financial data and physical material are not right.

Execute depreciation

Enter the term "Depreciation Management Depreciation Depreciation Month." The system automatically calculates the amount by the method of depreciation and the number of years entered in the card, generating a "Depreciation Bill of Lading." This document is the basis for the month-end entry, which generally summarizes "the accumulation of depreciation of fixed assets for the month XX."

The inclusion of new assets in the month is subject to the system's activation rules: some systems are introduced from the following day (the practice of most enterprises) or from that time onwards. The rules should be set at the time of initialization and not easily changed later.

Generate vouchers

Depreciation bill of lading is reviewed and sent to the master record module, where debits typically account for "management costs" or "manufacture costs" and crediters for "cumulative depreciation". If the enterprise goes to the ERP interface, this step is automatically completed; otherwise, manual export of data is required for accounting.

When Shanghai-based technology is implemented for manufacturing clients, it aligns depreciation rules with the firm's actual accounting practices, such as the direct attribution of the depreciated cost of workshop equipment to the cost of manufacturing and office equipment to the cost of management, so that no manual splits are required for the end-of-month accounting.

Change document: entire process from recording of assets to their end-of-life

The changes occur between the time of the build and the end of the life of the asset.

Document type Trigger scene System processing logic
Original value addition Major equipment repairs, upgrades Original value up, recalculated subsequent month depreciation
Departmental redeployment orders Transfer of assets from one user department to another Update the "User Department" field, and then the depreciation will change.
Impairment preparation form Significant decline or destruction of market value of assets The provision for impairment affects the book value of assets
Clean up the scrapping. Assets are not operational upon reaching useful life or destruction Elimination of original value and accumulated depreciation, balance into unserviceable income and expenditure
Over and above income bill The physical and financial discrepancies after the count Build new cards, run out of the waste process and identify the reasons

These documents go wrong, and the books go wrong. For example, a firm takes out an old equipment that is still in service, and the next month’s audit finds it running on the production line, and the account runs hard. So the document processing chain has to be closed by a dedicated person, especially for scrap orders, which requires the user department, the equipment management department, the financial triangulation.

Stocktaking: The days of the year-end reconciliation were busiest.

The fixed asset count is the most stressful time of the year for the system. Physical inventory tables and system bookings are paired, and differences tend to get the skin numb -- the card assets can be unmoved in the corner of the warehouse for three years or they may have been moved out of the register.

Practically, it is suggested that the following steps be taken:

  1. The inventory is preceded by the export of the "list of assets" (including numbering, name, use department, location) from the system and printed out as an inventory.
  2. When taking physical inventory, tick each item and mark the physical state (normal/damage/inactivity/loss).
  3. The inventory is followed by the recording of discrepancies in the system, which generates a statement of the excess and loss on the balance sheet and adjusts the books after approval.

A two-dimensional tag will be placed on each asset card, and the inventory will be checked directly with a phone scan, which will improve efficiency. A customer who runs storage logistics, with over 2,000 original cards being counted for one week, completed two days after the scavenger count.

Statement: What do management really see?

The system has a large number of statements, but the three types of reports that are actually used on a daily basis are:

These statements are generated directly in the system, and they are screened. It is important to note that the data in the report must be consistent with the "fixed assets" accumulated depreciation balance of the general ledger module, either not accounted for or not recorded in the document, or misrecorded in the initialised data.

A few habits of using the system.

The final recommendations to several levels of ethics were summarized after stepping through the pits:

The asset numbering rules are to be established at the beginning of the system, and it is suggested that they should be compiled by "Class code + Year + Stream" such as "SB-2024-0001". Follow-up is easy to search for or count.

The document is entered as far as possible on the day of the day, and is not added to the end of the month.

The initialization phase is an accurate one-time entry of the opening data, which is much less costly than repeated readjustments later in the period.

Fixed asset systems are easy, but they're thin. It's easier to keep them as routines than to attack at the end of the month. A system can really work, often not depending on how powerful it is, but on whether the person who enters them has done every process by the rules.