How to select an electronic label: a method for matching the frequency band, capacity and application in the form of a containment
Electronic label selection, set the frequency or set the scene?
The selection logic of the RFID Tag is really direct: scene-based bands, frequency-bands, distance-sets. That is, first think about where the labels are to be read, how far they are to read, what material the objects are to be put on, and then push chips and seals. Most people come up and ask "what frequency bands are good", which question is the opposite -- your cargo is in a warehouse, the shelf is on the production line? Forklift or machine sweep? Are there any requirements for metal, water, heat protection? These prefixes are not combed, and expensive tags are not used. Shanghai-based technology usually draws a three-dimensional watch for reading distance x environmental disturbance x batches, and sifts and chips from this list.
What's the LF, HF, HHF, each of these three bands?
The electronic labels are divided into three main groups of work bands, and their differences in physical characteristics directly determine the applicable scene.
- Low frequency LF (125-134 kHz)Reads the distance short, usually within 10 cm, with the advantage of being able to penetrate metals and liquids, almost without water or metal shielding. It is often used for animal earmarks, door-barrel cards, tool tracking, much more in livestock and car repair workshops.
- HF (13.56 MHz): Read the distance of 10 cm to about 1 m, protocol mature (NFC, ISO 14443, ISO 15693), and it is widely available on payment, ticketing, book management, medical device markings. NFC can read and write directly, which is its most convenient.
- UHF (860-960 MHz)Reads range from 1 m to 15 m, with the most distance from the direction antenna to 20 m or more. The mass reading speed is fast, and a single-time recognition of hundreds of labels is the mainstream program for logistics, retailing, warehousing points. It is afraid of metals, fluids, and needs to be matched with tags and adhesion.
A simple judgment when selecting a frequency segment: If you want to "bulk long-range group reading", the preferred UHF; if it's "close-to-peer, high-intensity interference," the choice HF or LF. Note that there is a slight difference in the distribution of the UHF band between countries, China is 840-845 MHz and 920-925 MHz, with separate FM for export products.
How do you choose the label capacity? The bigger it is, the better?
Not as big as you can, but the amount of data you have.
Common capacity ranges:
- 96 bit EPC+ small user area: Only one unique code (like a commodity barcode) is available for most logistics and retail scenarios.
- 512 bit to 2 Kbit: Small additional information on how many products can be stored, the duration of their life, and the place of production, which is much more useful in manufacturing.
- 4 Kbit to 8 Kbit• More complete traceability data can be stored for medical equipment, aviation spare parts, luxury goods and security.
- 64 Kbit and above: Used in specific industries, such as the Air baggage Label M class (AATA Spec 2000), which can be over 32 Kbit), library collections, etc.
The principle of selecting capacity is "already enough". The higher the unit, the more a unit, the more a few cents each, the less a hundred thousand, the greater the cost; the second, the increased time to write and read, the more the volume count. If you are just doing the cargo-to-port tracking, 96 bit EPC matches back-to-back databases with more than enough; really, we need to store trace information, so we suggest that we put detailed data on the cloud end, and only one ID code is in the label.
What are the forms of the seal? Where do they go?
The "look" and durability of the sealing decision label are the most easily pedaled links in the selection.
- Non-dry sticker (Inlay + paste)The most common, least costly, suitable for stickers, pallets, shelves. The disadvantages are weak metal resistance and unstable reading of the liquid environment.
- Anti-metallic tag (On-metal Tag): A magnetosphylactic material is added between the chips and the bottom, so that labels can be read in a stable manner on the metal surface. Common dimensions range from 50x15mm to 12x15mm. For tools management, metal shelves, and auto-composed parts marking.
- Zet / Hustler: cable, electrical equipment, baggage sorting scenes, back belt or latency.
- Hard Tag: Shell ABS or PC engineering plastics, IP67/IP68 protection level, high temperature resistance, chemical corrosion resistance. Used in laundry (drying 200°C industrial washing cycle), chemical drums, car engine compartment parts retroactively.
- Soft Anti-Metallic / Silicon Embot: Bendable, suitable for curved objects (oil drums, cylinders).
- PCB / ceramic label: High temperature-resisting extreme environments (e.g., spray lines at 200°C or above, kiln access reservoir) of up to 5 x 5 mm in size.
An easy point to ignore is the IP protection level. The label IP65 used in a warehouse is usually enough, but if it's outdoor open, cold storage (below -25°C), industrial washing is an extreme environment that must be above IP67 and confirmed as work temperature range. Many projects are delayed, the problem is "OK, production lines can be de-marked or unreadable for some time."
What is a typical mix of different industries?
The selection logic of several typical industries can be used in the context of practical project experience:
The clothing retail shop: The UHF(ISO 18000-6C/EPC Class1 Gen2) protocol, Non-dry laminated tags, reading distance 3-5 m, doing an inventory with the RFID handheld. The capacity is sufficient for 96 bit EPC, only coded for each dress + door shop backstage system.
Manufacturing linen-work management: UHF Anti-Metallic Tag, Note or PCB Envelope, Small Size (around 30x10 mm), and End 85°C working temperature. Capacity 512 bit to 2 Kbit, Store Load Number, Maintenance Record, Last Validation Date, etc.
Storage logistics tray level tracking: UHF Remote Label (10-15 m read), which is used to identify the path in conjunction with a door antenna. The labels are placed in a pan on the side of the tray, and are resistant to metal layers. In the volume scenario, it is recommended that Impinj Monza, Alien Higgs, etc., be selected for a type of card with high reading sensitivity.
Medical equipment / Survivors: HF (ISO 15693) on-metal tags housed in epoxy or PPS, rated for at least 500 sterilization cycles at 134°C, with 1–2 Kbit of memory for the instrument ID and wash count.
Books / Archives Management: HF (ISO 15643 / ISO 15693) thin, dry-defended glue labels with capacity above 1 Kbit and storeable information.
Car parts lined for distribution: UHF anti-metallic plus anti-liquid soft label, renegative oily, capacity 512 bit.
The difference between industries seems to be large, and essentially a combination of the three variables: "Lift + Environment + Data Volume".
The most easily stepped-in pits in the selection process.
Say a few things we actually met:
- Direct the URF label to the metal surface: Read distance shrinks from 8 m to 0.5 m, and cannot even read at all. The air gap must be made of metal resistant or by a sheeting of more than 5 mm between labels and metals.
- Liquid / High water-bearing goods are directly labelled with non-dry glueWater is strongly absorbed into UHF microwaves, with bottled water, fresh meat, fruit and vegetables, either by changing the HF label or by putting it on a bottle cover or tray.
- Too much of a mass reading error rateThe common cause is not labeling, but the direction of antennas to polarize, label angles to read power. It is recommended that tag attitude tests be performed on site: cross, vertical, tilt 30°, tilt 60° and round.
- Only the temperature is not considered for extremes.: Refrigerator, near ovens, outdoor tan, label performance will decline significantly. The type must be determined by the work temperature range (e.g. -40°C to +85°C) and the supplier is requested to provide a test report.
- Co-mingled chip model leads to reading and writing compatibility problemsThe different manufacturers' chips may vary slightly in the length of the EPC, password recognition, and TID area format. When multi-manufacturing, small batch compatibility tests are performed before large-scale production is made.
How do you test it when you do the selection?
The test is not "can read" but "how much can you read under real conditions." It's suggested to follow these dimensions:
- Distance Test: Fixed reading equipment and power, test label reading rate at 0.5 m/ 1 m/ 3 m / 5 m / 10 m, ideal status above 95%.
- Posture test: Cross, vertical, and persevering under-perceived.
- Batch Test: 100 labels on boxes, trays with a single read success rate of 98%.
- Environmental testing(b) High temperature (85°C/ 2 h), low temperature (-25°C/ 2h), high humidity (85% RR/24 h), and read rate decline after impregnation (IP67 waterproof 30 min).
- Age testThe reading rate declines after 30 days, 90 days. If the back tape is of poor quality, it starts to drop off in months.
The complete test report covers at least five of these. If the supplier gives only one "read-out 10 m" specification, there is no measured data, and it is recommended that a careful selection be made.
How do we control costs? Where can we save and what can't?
The label costs are mainly three pieces: chips, antennas, and sealing.
Where to save:
- If no anti-metallic need, choose General Inlay seals at a unit price of less than 2 gross yuan.
- The difference between 96 bit and 2 Kbit may be over 50%.
- Large-volume procurement (more than 100,000) usually has 20 per cent to 40 per cent of bargaining space.
Where we can't save:
- The direct reliability of the sealed materials and process is saved, which is not readable, and the cost of returning to work is higher.
- The cost of certification tests for special performances such as metal resistance, water protection and high temperature cannot be saved, which is the bottom line for compliance and stability.
- The chip selects a mature model (large volume, complete information) to avoid the risk of "small new chips" supply.
And one of the things that goes around is, the core of the electronic label selection is to sort out the five things in order. The first two steps decide whether it's good, the next three steps determine how much. The budget allows for small batch validation in real-life settings, then large-scale, the most secure path.

Ms. Lei
Mr. Pang