Identification principles for passive electronic labels and depth resolution of energy acquisition
RFID Knowledge

Identification principles for passive electronic labels and depth resolution of energy acquisition

PublishedShanghai Zejie Smart Technology Co., Ltd.

Let's get one thing clear: "No energy" is not "no energy."

Many people first heard the "unactive electronic label" and thought it was "unenergyful." That's the opposite: the energy of the label is entirely from an electromagnetic field launched by a reader, so the chip is connected to the antenna to keep the sensor voltage flowing straight, so the chip can be activated; identification is done by reverse dispersion, and the ID information is transacted on the back-reader. The whole process does not require batteries, but the effective energy range of the readers is removed, and the tag stops working immediately.

Where did the energy come from?

The way the labels get energy is essentially an electromagnetic sensor, as it was taught in physics. Reader and writer wires enter into a convoluted current, and they create a transmagnetic field around them; this magnetic field runs through the label's antenna, which, according to Faraday's law, senses a mutated voltage at both ends of the antenna. The chip is re-routed inside, presses, transforms communication into a straight stream, gives logical circuits, stores and adjusts circuits.

This requires the tag and reader antennas to be close enough for near-field coupling. How close depends on the frequency. At 13.56 MHz, HF RFID generally reads within 10 cm through inductive coupling. At 860–960 MHz, UHF RFID can extend range beyond 10 m through electromagnetic radiation and reception. At higher frequencies and shorter wavelengths, energy can travel farther, but performance becomes more sensitive to antenna orientation and surrounding metal.

How does energy decline when you're far away?

The inverse of the peri-sensor coupling power is a inverse ratio to the three-dimensional range of distance, and the energy density of the distant radiation is an inversely proportional to the square of the distance. In other words, the label is a little further away from the reader, and the sensor's voltage is falling rapidly. That's why it's also "unactive tag", different frequency bands, different antenna designs, with several orders of magnitude between a few centimetres and a dozen metres of dyslex, and the minimum start voltage of the chip is usually around 1V, which is the key threshold for determining the limit recognition distance.

Identification How to Finish: Reverse Scatter Mode

The energy problem is solved, and the next step is "How to tell reader how to get the memory." Here's a second hunch: Many people think, "How do you respond with a tag without a source?" The answer is not to launch it, but to change the "reflective back" load.

Four steps from being asked to answer

The process can be broken into four steps. First, the reader continues to send a carrier signal to space -- that is, the field where energy is provided. Second, the label antenna generates an induction current in this field, and the chip is wired. Third, the chip is connected to the data from ID in the memory, the load resistance of the control antenna interface is rapidly switched between "matching" and "deficit." Fourth, the resistance changes change the reflective properties of the antenna on the inflow wave: more when matching, less reflecting; less resonance when missing; and a high reflexion. Reader keeps observing back waves, decomposing these micro-changes that are made by the labels, and then recreates the full IID.

The mechanism is calledReverse Scatter Mode(backscatter migration). The label itself does not launch new energy, but changes the range of the wave being reflected back, phase or frequency. For a reader, it is equivalent to a weak response to the label in the echo of "self-screaming."

Energy and identifiers in different frequency bands

The essence of choosing which passive label is to balance energy efficiency and direction stability. The following table is a comparison of common frequency bands:

Frequency bands Typical recognition distance Concord Method Typical scene
125 ~134 kHz (low frequency) Within 10 centimeters. Electric connection. Animal labels, door-ban
13.56 MHz (HF) About 10 centimeters. Electric connection. NFC, bus cards, ticketing.
860-960 MHz (UHF) 3-15 meters Electromagnetic Reverse Dispersion Logistics, retailing and asset management
2.45GHz (microwave) 1-10 meters Electromagnetic Reverse Dispersion Partial vehicle identification, ETC

Distance is not equal to experience. Low-frequency and high-frequency tags are more resistant to metal, less selective about the label; UHF labels cover a lot of them, and can read hundreds at the same time, but when you encounter a metal shelf or watery object, the reading/writing distance drops rapidly.

A few common boundaries at the engineering site.

It is understood that several pits encountered in the course of the project are directly linked to the doctrine.Metal environmentMetals reflect electromagnetic waves, which cause the UHF label antenna to be severely mismatched with equivalent electrical parameters that could have been read at 8 m and could not be read at 10 cm behind the metal surface.Liquids and humans• Water is heavily absorbed into UHF signals and labels on liquid beverages or closes are often replaced with frequency bands or support structures.Multiple tag collisionsDozens of labels are also entering the reading and writing area, each of which is rewrited with reflect properties. The reader must be identified individually using collision-proof algorithms such as Aloha or tree spectrometers, which will increase rapidly with the number of labels.

The other kind of boundary is...Business requirements for speed of identificationAnd so the warehouse's out of the vault code requires reading multiple labels in hundreds of milliseconds, and there are ad hoc adjustments to the air protocol for readers, collision-proof parameters, label grouping. These details determine how well we know, not necessarily stable run through the field.

Back to application: choose which label to look first

Thread these up, and then go back to the selection. First, ask how far it is to read, whether there is a metal mask, whether it is single identification or mass inventory. Second step then fix frequency bands and chip types, whether collision-proof, whether password protection is needed, and how big the user data area is. Third step goes to match the reader, antenna, protocol stack and upper machine software.

Shanghai Zejie Technology regularly compares how passive RFID works in theory with actual operating conditions to find ways to improve customer deployments. One warehouse customer attached ordinary UHF tags to metal returnable containers. Read distance dropped from a theoretical 9 m to less than 30 cm. After switching to flexible on-metal tags and a compact circularly polarized reader antenna, read range returned to 4–5 m and the time to count a container fell from more than ten seconds to about two.

The source-free electronic label is not a "plugged" general hardware. It's sensitive to the physical environment, protocol design, antenna setting; but it's in turn because of clear principles, clear parameters, most problems with "not reading" and "low reading" can be dismantled, reproduced, solved. Putting this mechanism in place, you really understand the anomalies that occur in asset counts, production lines, intelligent storage scenes, and so on, with direct analysis access, and you can avoid pits that are easily pedaled at the programme design stage.