uwb electronic tags for indoor high-precision positioning and application resolution
RFID Knowledge

uwb electronic tags for indoor high-precision positioning and application resolution

PublishedShanghai Zejie Smart Technology Co., Ltd.

Why isn't the interior location a secure point for the base station?

Indoor positioning is not just a matter of installing a few more base stations. Wi-Fi and Bluetooth estimate distance from signal strength. Metal shelves, people moving around, and wall reflections can push errors to 3-5 m, which isn't good enough for finding tooling in a factory or equipment in a hospital. UWB tags instead use nanosecond pulses and measure time of flight to calculate distance, keeping positioning accuracy at 10-30 cm. This is why they are gaining interest in factories, mines, and hospitals.

How did the UWB signal get so good?

UWB stands for ultra-wideband. The signal occupies a very wide span of frequencies, generally over 500 MHz, and is transmitted in pulses one to two nanoseconds long. Together, these characteristics offer two advantages. First, they resist multipath interference: reflections from walls or metal equipment are less likely to blur together with short pulses. Second, time resolution is very high. Timing accuracy can reach about 65 picoseconds (1 picosecond = 10⁻¹² seconds), corresponding to distance resolution close to 1 cm.

The range is essentially a flight time measure, and the principle is similar. There are two common approaches:TOF(Time of Flight)(b) To allow the label to signal, recording the time of receipt of the signal at three or more base stations and repositioning it three points at a back-sliding distance;TDOA(Time Difference of Arrival)All base stations are required to be strictly time-synchronous, with only one pulse of the labels, and to be calculated by a time difference between the stations, more friendly for tag function and especially suitable for electronic labels for battery power.

The time-ring between the stations is the first project to resolve. The time-synchronizing of the IEEE 1588 precision clock protocol is usually done with fibre optics, which puts the time on the nanosecond level by shaking. In a standard plant, anchor points (base stations) are normally installed at the top of the pole or high above the wall, and the proximity point is controlled from 30 to 50 metres, ensuring that the distance is smooth and that the accuracy is stable.

How does a capable positioning system fit in?

The hardware core is three blocks: the UWB electronic label, which is attached to the object or person, and the positioning anchor (base station) in space, consolidates the upper position or locator engine for decomposition data. The label contains UWB radio frequency chips, MPUs and batteries, and is partially integrated into accelerometers and gyroscopes -- when the UWB signal is lost briefly, it can be extrapolated using a logjam to push the position forward for several dozen seconds to minutes, avoiding a locator flash.

One of the key steps in the deployment process is easily overlooked: establishing an accurate siteCoordinate Map. Survey each anchor's actual coordinates on site with a total station or 3D laser scanner, keeping error at centimeter scale. After installation, calibrate the system so it knows each anchor's position in a shared coordinate system. Each time a tag transmits a pulse, three to four anchors can then determine its current coordinates.

The retrofit rate can be adjusted to the scene: material tracking is enough for 1Hz, label batteries can last a year or two; AGV (Auto Guide) paths are defunct, and real-time positioning of people may require 10Hz or even 100Hz, with only weeks to months left. The program phase needs to match with the client -- how high dosage is needed, which directly determines anchor layout density and tag selection.

The three engineering issues that really don't fit in.

Multiple Paths and CoversMetal equipment and concrete walls reflect the signal, decipher a long distance, and then divert the position from its real location. The circumvention is to use as many of the anchors as possible, with good vision ranges, and to bypass the large metal shield; the algorithm level is to be identified by NLOS, which removes the clearly deviation measurement.

Environmental interferenceWiFi, Bluetooth, and other UWB devices coexist with each other. Different countries have different frequency provisions for UWB, China uses the 6.0 to 8.5 GHz segments. Design phases are designed to plan frequency and launch power control, avoid interference with other equipment and reduce the impact of external signals on their own systems.

Cost and maintenance. The cost of a single UWB anchor is higher than normal WiFi AP, and three or four hundred square meters of plant usually requires 4 to 6 anchors for stable coverage. The label card ranges from several hundred to thousands dollars, which is then crushed in bulk. The later load is mainly battery replacement and anchor location verification, part of which is written into the daily point-check process, otherwise the system's accuracy will slip quietly after a year.

A few typical scenarios already in use.

Plants and storageForklift positioning, AGV routing, real-time inventory of valuables. Shanghai-based Cheeky Way Technologies Ltd. has served a client who does precision machine processing, and over 3,000 packages in the workshop were used to be manually counted, which takes two people three days per month. When the UWB label is placed on the work clothes, the backstage shows a direct real-time location, and the vault becomes a matter of minutes, and the loss rate of tools is reduced from 8% to less than 1%.

Hospitals and old-age institutionsRespirator, monitor, and wheelchairs, which often move between different areas of the disease, are inefficient to check their location by telephone. Electronic labels can show the floor and room numbers of the equipment in real time, the nurse station is directly visited, a lot of invalid movement is saved; the old-age scene is also used to prevent the mentally retarded from going astray, and an automatic warning is made when crossing the border.

Mines and tunnels. Underground positioning has long been difficult; GPS, Wi-Fi, and Bluetooth have not solved it. UWB pulses penetrate somewhat better. A single base station mounted on a tunnel wall can cover hundreds of meters. When workers wear tags, surface dispatch can track each team's location in real time and quickly find trapped workers in an emergency.

ConstructionThe location of towers, lifts and large prefabricated units is tracked for real use in movement control and security. The construction site changes very quickly, changing the positioning environment every time the building enters and turns the towers. The UWB label is a suitable fit to post it.

We can't get up to UWB.

First, do you really need accuracy within 10 cm? If 1–2 m is enough, UWB costs more than Wi-Fi or Bluetooth and is unnecessary. Second, is there room for at least four anchors with good line of sight? UWB loses its advantage in low spaces with extensive metal obstructions. Third, can the budget cover anchors, tags, the positioning platform, and ongoing operations? Backend software and algorithm licensing are major costs as well as hardware. Proceed with selection only if at least two of these conditions are met.

The selection of the supplier focuses on three things: first, whether there is an on-site experience in the industry — UWB's accuracy is sensitive to the details of deployment, and projects made by untaped teams tend to run off two or three months; second, whether the calculator engine is self-studyed — dependent on third-party open source platforms being limited for subsequent upgrade; and third, tag re-launching, backstage data analysis, if the long end capability is available — can the system stabilize after a year, often depending on these details.

The UWB itself is a more mature technology, and the IEEE 802.15.4z standard regulates both the physical layer and encryption. What really determines the success or failure of the project is not the theoretical precision on the parameter table, but rather the actual footing, anchor layout, algorithms to adjust these landing details. These are places where high-precision positioning in the interior can be transformed from "cm" on the PPT to real ability in the workshop.