Elements of structure and mass application for nfc stickers
RFID Knowledge

Elements of structure and mass application for nfc stickers

PublishedShanghai Zejie Smart Technology Co., Ltd.

The NFC post is essentially a sandwich structure, so it's only possible to get a mass application after the level.

The NFC sticker looks like a thin label, actually made of chips, antennas, three layers of the base, and optional back-and-face. The chip is used to store and interact with protocols, most commonly the NTAG series of NXP, ST25 series, working frequency 13.56 MHz, following ISO 14443 or the NFC Forum Type protocol; the antenna is a chain of aluminium or copper wire that is etched on the matrix, and the number and diameter of the rings determines the distance from which to read; the base is more than PET or paper. Any problem in this layer affects the electrical capacity of the final plate, so when you do a mass project, you suggest that you eat through the structure and then talk about production.

The chip selection isn't as new as possible, depending on the amount of data and protocol.

The differences in chips are mainly reflected in three parameters: user availability, NDF format support, and automatic locking.

When we do a project, we usually suggest that the client fill out a small table: single data bytes, need for rewriting, read-card distance requirements, and mobile phone coverage.

Antenna shape determines the distance to read and also the position to post.

An antenna diameter is a direct factor in reading distance. The 35-40mm antenna can be read from 4-6 cm on the mainstream phone; around 50 mm can read 5-7 cm; and smaller antennas below 25 mm can drop to 2-4 cm, with a high sensitivity to cell phone locations.

There are also several antenna shapes:

There is a pit that can be easily stepped on when the batch is pasted: the metal on the back of the sticker will significantly shorten reading distance, or even fail to read at all. If the product itself is a shell of metal, it is necessary to choose a special patch with buffers or to reset non-metallic plane.

Pre-volume engineering verification. Three actions are not saved.

The entry of the sample test for the antenatal period determines whether the rate is stable. Three actions are critical:

  1. Sample multi-machine measurements: Test iPhones and multiple Samsung, Huawei, Xiaomi, and Redmi models across price ranges. Use at least six models covering both iOS and Android. Make at least 20 consecutive reads per model and log the success rate and read range. Flag any model with insufficient range or a failure rate above 5% in the delivery documentation.
  2. Temperature Cycle TestThe sticker is usually followed by a three-wheel cycle of storage, transport and use, from -10°C to 60°C, to see if the chip round is broken and the antenna line breaks. This link is particularly important for outdoor equipment and industrial products.
  3. Curved-up test: Whether arc-shaped bottle, argon-based electrocution surfaces are readable after they have been applied, and the thickness of the glue and the treatment of the buffer are determined at the sample stage.

The three actions taken together take two to three weeks, and the compression period will lead directly to a volume phase problem.

Code and personalize. Two steps to separate.

Many people mix codes with personalization, but it's two things.

There are two common ways to code a lot: send the URL list to the sticker provider, burn it in bulk before leaving the factory; and burn it with its own encoder when you get a nudist sticker. The former is less expensive but has to keep data confidential, while the latter is more flexible than that with coding equipment and scrutinizing. We recommend the first one when we do the medium batch, which reduces the probability of error on-site operations.

Three common pits of the adhesive process

The rate of evaporation in bulk packages is concentrated in three main areas:

The good rate is only contained if it is stable at more than 99%. Below this value, the positioning and alignment are re-examined.

And then you have to look at one thing when you land: the probability of a view not being read.

Posting the product delivery is not an end, and the probability of being invisible in a real picture is the real threshold. There are three common reasons:

  1. The sticker is overheated by ink or thin membrane, and the NFC signal is absorbed. The solution is to leave the induction area uncovered by ink or use a specific transparent ink.
  2. If a user's phone is too old or its NFC antenna is in an unusual spot, placing the tag against the center of the back may not work. Put a diagram of the detection area in the product instructions.
  3. Repeats the UID when you burn in bulk. Repeating the UID will cause individual mobile phones to jump wrong page.

Shanghai has found in several mass-production projects that have been done that the real impact on delivery is often these three small problems after landing, rather than the electrical performance of the stickers themselves. By aligning them with their clients ahead of time, the project’s ultimate experience will be much more stable.

Serialize the above points into a minimum workflow.

Back to the beginning, it's not really complicated about bulk NFC stickers. The process is: first determine the chip capacity and antenna form, then model multiple machines and heat, then separate the code and the patch, and then look at the view and see if you can't read it. Any step is saved in the next exposure.

It is recommended that you start to contact the bulk project operator by running the above process over and over again, taking into account cost optimization and scaling up. After a run-off, the next batch is fine-tuning the parameters.