nfc label selection guide: complete analysis of chips, form and cover
The lessons of a choice from a return to work
Last year, a smart check was made to a warehouse, and the first NFC tags were dropped in a large area within two weeks, and reading distance was abruptly close. The chip was unturned, and it was found that the chip was selected for general use, and the form was used in the most thinest form of flexible inlay, and the sealing was the single layer of PET remembrane -- the metal surface of the shelf with forklifts to vibrate back and forth. And then the chip, the form, the three dimensions were removed and re-evaluated, and the solution stabilized.
The NFC label type seems to be "select a readable label", but the answer is three questions: the chip determines how much data can be stored and what protocol to communicate with; the form determines the physical shape and how the label is installed; the sealing determines how bad the label carries. The triads cross-judge, so they don't get wrong.
Chip: Decide what the label can do.
The chip is labeled "brain." The market mainstream NFC chip is arranged into two families: ISO 14443 and ISO 15693.
ISO 14443 family is short-reading and writing distance, usually within 10 cm, but the protocol is ripe, and the phone can read directly. The most common is NTAG series of NXP - NTAG 213 capacity 144 bytes, NTAG215 is 504 bytes, NTAG216 to 888 bytes. The asset count, the inspection card, which requires only an ID and a small amount of custom data, and the NTAG213 is basically enough, and stock is the most stable.
If you want to have a complete URL or multiple inspection log in the tab, 144 bytes unfilled, it is recommended that you go directly to NTAG216 or use the back-end system for short chain mapping. NTAG215 is much more useful in encrypted games cards, NFT security, but it is an ecological, non-general industrial scene.
ISO 15693 family reading and writing distance of about 1 metre, requires a dedicated reader, cannot read it on a mobile phone. Use the logistics sorting, laundry management, book-tapes to take this view that requires a long-range mass reading. ST25 series and Tag-it series are representative chips for this type.
There is also a category of MIFARE Classic, which is common in a cartoon, a closed system. It's not the same type as NTAG, and if your door-ban system is MIFARE Classic environment, the new label will be the same series, otherwise it won't be read. The compatibility problem is the most easily ignored pit in selection.
When we make an optional assessment of the client, the first step is to list the customer ' s card reading equipment and cell phone compatibility, then push the chip model and avoid a mismatch between protocols.
Form: Physical shape determines the applicable scene
The chip is fixed, the form is "What the label looks like and how it's fixed."
Inlay is a naked coil and chip, without the shell, with a thickness of about 0.1 mm, which is suitable for posting to cards, embedding within products, or hiding under stickers. Soft ininlay bends dozens of times, but barely resists metals, and can't read them on metal surfaces.
Round coin labels (commonly 20mm, 25mm, 30mm) have a self-repeated reel that can be attached directly to the equipment's shell. If it is a metal surface, you must select a version of an anti-metallic layer — i.e., a steel-oxygen absorbent between the label and the metal. A coin label without a metallic layer is placed on the metal, and reading distance is reduced from a normal few centimetres to a few millimeters.
The hard-shell label (ABS shell or epoxy encapsulation) is strong in impact and waterproof, suitable for an outdoor, vehicle, equipment machine.
And there's a printable NFC label, which looks like an ordinary non-dry glue, but it's embedded in inlay, and it's suitable for mass posting to product packaging for trace. The label itself is not high temperature, and you have to look at the temperature of thermal contraction when you put it on the outside of the heat membrane.
Encapsulated: determines how long the label will last
The way in which the sealing is made directly affects the life of the label and the ability to adapt to the environment.
PET rembrands are the most common low-cost cover, small thickness, low cost, suitable for paper, plastic, indoor environment. But PET is not hot enough to run at 80°C, and alcohol rinse can also turn on the edges. If the disinfection is much more used in a warehouse, the PT label will last less than a year.
Episode seals contain chips and wires in epoxy resin, which are strong water-resistant, resistant to chemical corrosion and often used for industrial cleaning. The disadvantage is increased thickness (generally 2-3 mm) and epoxy is yellowed under long-term ultraviolet light.
The ABS shell can be protected by hard labels that are IP67 or even IP68, which can be immersed in water for short periods of time. This label is used for outdoor equipment, power patrols, city well covers. It is typically installed as a screw-fixed or strong backlash, and then a gauze if necessary.
The temperature range is another key parameter. The working temperature of the regular NFC chip is between -25 °C and 70 °C. If used in cold storage (-40 °C) or high temperature workshops (above 85 °C), the specification of the chip should be confirmed with the supplier at the selection stage, not just in brochures.
There is also the back-tip option. The normal backglow is not well-stamped on the rough metal surface, and 3M VHB, which is a high-strength glue, is suitable for long-term fixation, but when removed, it leaves the residue. If you need to change label positions regularly, select a hard shell with a screwdriver, instead of relying on the backglow.
Cross-judgment of three dimensions
To put three dimensions together, the selection is a cross-cutting issue.
First step is to agree: can a mobile phone read or must have a dedicated reader? This determines whether the chip follows ISO 14443 or ISO 15693.
Second step: What do you want to store in the label? Do you want to save only one ID number, or a full URL or several records? NTAG213 cannot load the next complete URL (unless it is short-chained), and this time either NTAG216, or the backend system.
The third step is the location of the installation: where to put it? Metal surfaces, plastic surfaces, outdoors, high temperatures, damp? This cut-off is largely established in form and seal.
Step 4: Set the expected service life. Does the tag need to last one year or five? PET lamination suffices for one-time traceability, while ABS housings are better for long-term asset tracking.
After this four-step, the candidate model is basically down to 1-2, and a small batch of test-based reading space and effort. If there are dozens of different applications in the project, it is recommended that an internal selection table be created, with protocols, capacity, form, wrapping into drop-down options, avoiding double evaluation of each project.
The most easily pedaled pits for NFC labels are only unit prices. The lowest price is often the least chip-capable, thinst sealed, and weakest in the environment. When a lot of it is done, the cost of returning to work is far more than the savings.

Ms. Lei
Mr. Pang