rfid label selection guide: frequency band, material, process and situational relevance resolution
And first, the conclusion: there's no "one-size-fits-all" label. There's only "right on."
The core of the RFID label selection is to align the four things that you use in your actual scene. The frequency segments decide how far and if you can read and see through, the material determines how long the labels are in the environment, the process decides how or how, the first three things are enough. Our experience is: 80% of the project returns not because the label quality is bad, but less than one or two of the first types. Below is a discussion of how the four dimensions are judged.
The frequency is set first. Three things are left to make sense.
The frequency range is the first sift of an chosen type because it directly determines the distance, speed and availability of reading in "hard-to-read" environments such as metals, liquids.
- Low frequency (LF, 125-134 kHz)Reads within a range of 10 cm, which is virtually free from water and metals, suitable for short distances such as animal earmarks, door-barrel cards, and high requirements for penetration.
- HF (HF, 13.56 MHz): Within typical distance of 1 m, often used for book management, electronic ticketing, single-grade tracer, and more tolerant to liquid environments than the UHF.
- UHF (UHF, 860-960 MHz): Read distance can be achieved from 1 m to more than 10 m, which is the main frequency of warehousing logistics and retail count. However, when the UHF labels are placed on metal surfaces or liquid bottles, reading distances shrink significantly, if not completely read.
The way to judge is simple: first, you need to read "how far away" and "how fast" and then see whether the object you label is metal, plastic or liquid packaging. The frequency is not selected. The back of the material and process is wasted.
The material determines how long the label will last.
The RFID label is actually two layers: chip plus antenna.Noodles.(inlay, usually PET or paper-based), and outer layers.Encapsulate。
- Paper is dry.: The lowest-cost option for disposable or short-term use, such as garment hangtags and shipping labels. The usual temperature range is -20°C to 80°C.
- PET + plastic shell: Temperature and chemical tolerance are better suited to industrial production lines, outdoor assets.
- ABS or PC hard-shell: Resisting from shocks, able to screw or strap and often used in tools, molds, and swingbox management.
- Ceramic or special composites: High temperature tolerance of 200°C or more, suitable for pre-welding process in cars, engine parts and components retroactively.
To give a specific example: a factory that does this, which puts the label on the mold and then goes back to the oven (160°C), if it starts with a normal PT tag, then the face is frowned three or five times, the chip fails, and the whole data is broken. In this case, the material upgrade is necessary, not optional.
Processes and forms, which affect how you load it on the product.
This process is often underestimated, but it directly determines whether the labels are successfully embedded in your product or packaging process.
- No dry glue.Manual or labeler automatically postable, efficient and suitable for the outside surface of a box, tray, or container.
- Notet plastics embedded (Incert moving)• Puts inlay in a mold, plastics in a single form, labels integrated with products and suitable for swing boxes, plastic trays, medical devices.
- Band-tight/snack/stair nail fixed: Common practices for hard-shell labels, metal, wood and concrete surfaces.
- Hang tag(b) Clothing, footwear and luxury goods are commonly used to facilitate back-track process scanning.
We saw a situation in the project: the customer chose to use the UHF hard-shell label, but the installation was half-blocked by the metal frame, and the reading distance fell from 5 m to less than 1 m. Then we went out of sidelines, the way the chute was installed, and the problem was solved. If the process was disconnected from the live assembly, the expensive tag could not be read.
Work is right. It's the last and easiest step to pull over.
The job is the most variable in four dimensions, and it contains at least five things:
- TemperatureLow temperature - 40°C, high temperature - over 200°C, all require a special face and chip programme.
- Chemical corrosion(b) ABS is subject to corrosion by certain solvents.
- Mechanical stressVibration, bending, shock, soft-skinned, more resistant than pure.
- Surface material: Metal surfaces shall be labelled "anti-metal" (with suction material layers) and a normal UHF label shall be marked with a mirror.
- Read & Write Environment: Whether there is a shield, multiple labels are intensive and read speed requirements (number of times per second) to determine the chip sensitivity and conflict-proofness of the label.
For asset management on metal totes, choose on-metal tags and make sure the inlay bonds firmly to the RF absorber. Otherwise, repeated heat and humidity cycles can cause delamination and reduce range. Liquid containers such as water jugs and chemical drums pose a different challenge. Put the tag near the top or use a specialized antenna to avoid UHF attenuation by the liquid.
Selection to land: this is recommended for three steps
We'll do it in three steps.
- First step set frequency band: Clear reading distance, speed of reading, whether in the metal/liquid environment, LF/HF/UHF triangulation or superimpose.
- Second step of material and process: Filter the candidate labels for 2-3 according to five profiles of temperature, chemical, mechanical, surface and installation.
- Step three, do a live test.: Run at least one complete process (poster-read-written-clean-read) in the real environment, not just laboratory data.
This step was measured on the ground, but experience tells us that the 10 m reading distance label in the lab is probably only 3 m in a warehouse full of metal shelves and forklifts. It takes two days to do this, saves the rest of the months of trouble.
A couple of easy-to-touch pits.
And finally, we'll leave a few holes that we've stepped on with our clients to remind the first-time pickers:
- Choosing by chip alone and ignoring the antenna design: the same chip can deliver more than a threefold difference in range with different antennas.
- Foreign frequency bands are directly used at home - different UHF bands in different countries, 860-960 MHz is a zone and cannot be read without local compliance bands.
- The protocols are used in common - Gen2 and ISO 18000-63, but some private agreements only recognize specific labels and confirm them in advance.
- Overestimating service life: a vendor's ten-year rating usually assumes ideal conditions. For outdoor or industrial use, half is a more realistic estimate.
The RFID option is not a one-time technology purchase, but a process of untangling, aligning and revalidating the use of the scene. The four things that are considered to be frequency, material, process, and condition can be really stable when labels are running.

Ms. Lei
Mr. Pang