Choosing RFID Tags for Fixed Assets: Tag Types and Operating Conditions
At an electronics factory's year-end count, staff had tagged more than 1,000 assets in the warehouse, but a walk-through with a handheld missed 20% of them. Investigation showed that neither the reader nor the back end was at fault. The tags were a poor match for the surfaces they were attached to. Choosing RFID fixed asset tags is less about frequency than matching tag construction and mounting method to the asset material and site conditions.
Step one: determine where the "never read" card is.
The labels are not readable, usually for three types of reasons: interference with signals by the material of the object; misposition of the installation and the dyspnotic orientation of the reader ' s antenna; or failure to cover the label itself in such a way as to hold on to the site, such as high temperature, oil pollution and metal masks.
Metals and liquids are the two "killers" of RFID signals. The metal surface reflects an electromagnetic wave, a normal soft label is mounted directly, the reading machine antenna's energy is reflected, and reading distance falls from three or four metres to ten centimetres of theory; the liquid is very absorbed into ultra-high frequency signals, placed on a drum full of liquids, which also has bad times. This is particularly evident when the warehouse or workshop board is counted, where iron leather cabinets, metal shelves, chemical barrels, Note plastic moulds are almost all handled separately.
Step 2: Narrow down the tag category by frequency and the material it will be attached to
The RFID labels are low-frequency (LF, 125-134KHz), high frequency (HF, 13.56 MHz), UHF, UHF, 860-960 MHz, three-tier. The most used in fixed asset operations is URF because of the distance from which they read, support multilabel group reading, and can sweep hundreds of them in one second, especially for bulk count. But the URF’s ability to resist metals and liquids is weak, and needs to be compensated by a label structure.
If the asset is a metal shell equipment, an iron cabinet, an engine box, a mold, priority is given to suction material or a containment layerAnti-Metallic Tags. These labels are thicker than normal flexible labels, with an additional internal magnetic material or bubbled cotton cushion to stabilize reading distance by blocking the vortex effect of metal surfaces.
If the asset itself is non-metal, such as plastics, wood, paper packaging, normal soft Inlay (a naked label without shell wrap) with 3M back-up, there is no need to spend more on metal resistance. The HF frequency is usually used in door-barrel cards, small tools to manage short-range scenarios of this kind, and relatively little use is made of fixed assets.
Step three: Compare the situation on the ground with the situation.
When you have a big class, the environmental parameters are affected. In the projects we've done, labels are off, unread and corrupt, most of them with no tightness.
- Temperature: Standard tags operate from -20°C to 70°C. In cold stores below -30°C or workshops above 80°C, the adhesive layer and chip encapsulation are affected. Choose a wide-temperature industrial model and check both the storage and operating temperature ratings on the datasheet.
- Humidity and water: Outdoor or aquaculture-related scenes, which require labels above IP65. IP65 means that they are completely dustproof and can withstand low pressure water column wash, while IP67 allows for short-term inundation. Select which, depending on whether the asset will be washed, bubbled, rained.
- Chemical corrosion: Electric plating workshops, chemical storage, diesel-fueled around, and often acid or oil fog in air. Ordinary paper labels and ABS casings (a common hard plastic) are not carried out, long-term labels are flaring and the word is blurred. The outer crust material is replaced on this occasion with durable chemicals such as PC (polycarbonate) or PPS (polyphenyl sulphides).
- Ultraviolet and Aging: Outdoor open-air assets, with direct sunlight accelerating the loss of the gel. The ad hoc formulations for anti-UV labels are available, the outer shell is white or shallow and less heat is being taken.
Step four: Installation follows asset pattern.
The type of label is a direct measure of how long it lasts.
- 3M back-tape: Construction is fast, and it suits smooth plastics and metal surfaces, but it is easy to remove them in oily, rough, arc, long-term vibrations.
- Stitch or screw fixedThe price is to pierce the asset, which may not be applicable to some sophisticated equipment or after-sale warranty.
- Zacer or hangingPipes, cables, toolboxes, and loaning equipment are common. The advantage is that they do not destroy the asset's very nature, and the disadvantage is that plasters themselves become old and fractured and require regular inspections.
- Embedded or Injected: The label is pre-filled at the asset production stage or sealed in a tank with epoxy resin. It is so well hidden that it cannot easily be torn, but can not be replaced if it is broken.
The location of the installation is also described: try to avoid metal masks, avoiding the dead corner of the handheld's customary position; the UHF label will be read in a direction consistent with that of antenna polarization (usually wiring), and even if the label is mislabeled by five degrees, reading distances will decline significantly.
Step five: the parameter list doesn't count.
Every selection ultimately needs field testing. A tag rated at 3 m may read reliably at only 1.5–2 m in a warehouse. Reader power, antenna gain, nearby metal reflections, and environmental interference all affect signal strength.
Three things were suggested for the acceptance:
- Batch Consistency Test: Draws 30 to 50 labels of the same model, each of which is placed on a different location for the same asset and records the reading rate. A label cannot be read in an individual case, more than 10 per cent cannot be read or re-engineered.
- Walking route test: Follow the physical course of work of the inventory officer to see which locations will be blind, record them and then target the help antennas or adjust the label position.
- Multiple tags and test: Validate the speed and accuracy of a group reading when there are dozens of assets on the shelf. The normal UHF label group is good enough to read, but if stacked or surrounded by metals, it's necessary to measure impact-proofing.
Shanghai Selective Technologies typically sends a few samples to the site when they are labeled by some manufacturing and storage customers, measuring the process from above, then deciding on the type of bulk purchase and supplier. This is not an easy way to save, the parameter table is so beautiful that it is free to run.
Several issues that are easily overlooked in long-term use
- Label ID MonumentEach label is issued in the only TED (label identifier) and writeable EPC (electronic product code) area worldwide. The asset management backstage is usually tied to the EPC.
- Data Writing Capacity: Some scenarios want to put asset names, date of acquisition, responsible person in a label, user areas for HF and UHF tags range from hundreds to thousands of bytes, selected on a needs basis.
- Tore and transfer.High-value assets or security devices that can select a label with torn protection - the chip is torn apart and the tag is not working. The label is slightly more expensive, but it is valuable in a secret or anti-piracy scene.
- Matching of label life cycle and asset life cycleSome outdoor or industrial labels have a 10-year life expectancy, but the actual working environment is more stringent and can reduce it significantly.
Choosing RFID tags for fixed assets is straightforward as long as every specification matches the operating conditions. Choose on-metal tags for metal surfaces, wide-temperature tags for extreme temperatures, high-protection tags for damp or outdoor environments, and a mounting method that suits the asset shape. Once those choices are clear, test on site and collect data. Seventy percent of the benefit comes from selecting and applying tags correctly in the field; only 30% comes from the backend system.

Ms. Lei
Mr. Pang