How does the management of electricity assets RFID work?
Industry News

How does the management of electricity assets RFID work?

PublishedShanghai Zejie Smart Technology Co., Ltd.

Many people think that the power industry is a simple electronic label for the equipment, and what really determines the value of this system is security control of the appliances -- the floor knife, the electric pen, the insulation gloves, the wire, the missing one, or the wrong means to be brought back to the scene. The real use of RFID is to turn every piece of work into "a talking asset", who gets it, when it comes to, where it is, and how it is, which is well documented.

The pain in the power-manager's equipment management. Why can't traditional methods hold?

The number of appliances at the power station is quite high, and an average 110kV transformer may have to use between a few dozen and hundreds of safety devices. Traditional management depends on desk accounts plus paper-based lead orders and visual inspection, which is clear:

The common cause of these problems is that there is no "identity" in the work equipment and no data marks during the migration process. The only solution to RFID’s problem is to issue a single electronic identity card for each tool.

What exactly does RFID do with the safety of equipment?

In the actual project, RFID controls not the label itself but four key actions:

1. The person is bound by the contract.The tool cabinet is front-hand with a staff card, while the door opens with an automatic reader to identify which tools are removed and to bind them to the user account.

2. Return of automatic verification.The tools are put back in the cabinet, the readers are searched, the system reconciliations -- is it all returned, or is there any more unregistered instruments? One less report on the spot and locates which lead out.

3. Test-state association.The insulation tool is subject to a preventive test for six months, and the certificate is marked with RFID, the date of the test, the duration of the test, and all the testers are written into the chip. The system automatically judges when you take it -- the tool cabinet door that exceeds the validity period cannot be opened, and must be checked first.

4. Retroactivity in the field.The device is entered into the power station gate by a channel reader (RFID door-bar), and enters and exits, and corresponds to the automatic logout of the worksheet. Once again, the unloaded tool is in abnormally high condition, and the backstage will be warned.

The four steps involved the complete process of the work equipment from the warehouse to the site and its return, which resulted in a closed loop that could trace each tool.

What about labels and devices when you actually land?

The requirements for RFID and logistics storage are different from those for equipment management, with three main points:

tab selected.Metal surfaces (ground knife, wick sticker, lined copper) must be marked with anti-metal labels, and normal tags should be placed to read cards from a few metres to a few centimetres or not read. Insulation devices, plastic shell meters can only be labelled with an average UHF. Temperature is also key - some tools have temperatures above 70 °C in summer cars, general tagbacks are released, technical labels are recommended, work temperature covers -40 °C to 85 °C.

Reader set.The tool cabinets usually use UHF-UHF per diem antennas (power 1-2W), with a recognition distance of 30-80 cm, to avoid one cupboard reading the next. The gate channel is 4 antennas or 8 antenna arrays, which read a range of 3-5 metres, and infrared triggers to make a human identification person, and tools to identify a tool.

Data interface.The RFID system does not normally run alone, needs to interface with existing furniture and equipment accounts, EAM (Employer Asset Management) or PMS (Product Management System). The interface recommends standard API, return the access to the event, push the test status to the upper level of the system, and avoid becoming an information island.

Shanghai-Tai Jitai technology has done similar landfalls in several local grid-based storage projects, and details of label selection and antenna layout will have a direct impact on the rate of follow-up cards, which is not lost during the previous site survey.

A couple of easy-to-touch pits.

Pit One: 100% recognition.The occasional failure of the UHF labels in a dense metal environment is normal and generally sufficient for more than 98 per cent. The remaining 2 per cent is based on process bottoms — for example, one manual check-up per month, without recommending that the system be complicated to the same level of 2 per cent.

Pit II: Ignore the physical life of labels.The RFID labels also have life, high temperatures, oil pollution, and repeated bending can lead to failure. The labels on the furniture are recommended for replacement with a preventive test every 2-3 years, so do not wait until read.

Pipe Three: Just "where," whatever.The location tracking is only the basis, and these data, combined with test status, number of usages, damage markings, can be much more valuable. How many times a insulation glove was used and how long before the last test, the RFID chip could have been loaded with these fields.

Pipe Four: Ignore the practice of field operations.When the system first goes live, frontline staff may find it cumbersome and bypass RFID when taking items. Without adequate training and oversight, the system becomes ineffective. Start with one or two teams, get the workflow running smoothly, and then roll it out more widely.

It's not worth it.

If you're thinking about RFID for electrician appliances, you can answer three questions first:

  1. Are there any problems with lost equipment, wrong scenes and untested tests? How many times a year?
  2. Can you tell me in 10 minutes, when the accident is over, who was holding this tool and whether it was fit?
  3. Are the existing billings electronic or paper?

Two or more of the three questions are "unsure" or "failable," and RFID controls are necessary. It is not fancy technology, but it turns what you write into a system of automatic running, automatic alerting.

The core of the electrical equipment safety control is "preventable, retroactive, and back-to-back," and RFID is a tool to put these three things down to data level. The selection phase is a tool for mapping the situation on the ground, for involving first-line people in process design, for using data in the operational phase -- this is not just a set of labels.