What are the technical routes for asset locator counts?
Whether the asset locator count selects RFID or UWB depends on whether you are going to address "Quick Identification and Inventory" or "Super-Access Location". The RFID is suitable for bulk reading of asset labels, and UWB is appropriate for tracking changes in location within the region; if both an inventory and a location are required, it can be used by reference to asset value, frequency update and field environment combination.
What are the common technical routes for asset locator counts?
Common options include barcodes or QR codes, RFID, Bluetooth, Wi-Fi, UWB, and satellite positioning. Barcodes and QR codes must be aimed at manually and suit low-cost, on-demand checks. RFID uses radio waves to read tags and can reduce individual scanning. Bluetooth and Wi-Fi support indoor zone positioning. UWB measures signal travel time for precise ranging, often indoors when finer positioning is needed. Satellite positioning is mainly for outdoor use.
The selection of a model should be based on the meaning of "location": if it is necessary to know whether the asset is in a particular warehouse, a post or area, regional identification may be sufficient; if it is to determine the specific location of the asset within the room and to update the position continuously, focus on positioning precision, refreshing frequency and station deployment conditions.
What kind of problem does RFID solve?
RFID exchanges information with labels. The passive label is not self-contained, activated by the radio frequency energy from the reader; the active tag is battery, which can send a signal. The actual reading distance is influenced by frequency bands, label type, readers, antenna setting, and field factors such as metal and liquids, and cannot be judged solely on product nominal distances.
- Suitable:(c) Intake, exit, inventory, route check and determination of whether the asset enters or leaves an area.
- Advantages:The label can be read in bulk and less case-by-case; the label can bind business information such as asset numbers.
- Limitation:The normal RFID reading results usually indicate that the label enters a valid area of the reader and is not equivalent to an exact coordinate.
What's UWB fit to solve?
UWB (superbroadband) positioning is usually made of asset tags, fixed anchors and positioning software. The system calculates the position based on the range between the label and multiple anchors, so it needs to plan anchor positions, install heights, power and communications, and calibrate them in situ. Covering, reflect and anchor geometry affects results, and actual performance should be based on field tests.
- Suitable:Continuous check of the location of assets in the interior, tracking of movement paths or determination of whether the asset enters a particular area.
- Advantages:UWB is more focused on continuous location estimation than the RFID programme for only reporting areas, and applies to management tasks that require change of location information.
- Limitation:The tags require power supply, and the system also needs to deploy anchor points and maintain a positioning network; the number of assets, their frequency of renewal and coverage will affect equipment configuration and transport workload.
How does RFID compare to UWB and choose?
| Contrast | RFID | UWB |
|---|---|---|
| Key findings | Identification of labels, determination of whether they pass or are in the reading area | Estimating the location of labels in the room and tracking changes |
| Typical mission | Batch counts, access libraries, area checks | Real-time positioning, path tracking, regional cross-border judgement |
| Site construction | Configure labels, readers and antennas, focus on the reading range | Configure positioning labels, anchors and software, focus on the verification of coverage and calibration |
| Main considerations | Label type, reading and writing area, material of the article, reading leaks and error | Ocupine layout, shielding of reflections, refreshing needs, tag continuation |
If the goal is to reduce manual inventory loads, assess whether RFID meets identification and regional verification needs; assess UWB deployment and maintenance conditions if managers need to know where the asset is located in the room. Shanghai-based Cheeky Way Technologies suggests combing the list of assets, field maps, positioning particles, updating frequencies and permitted miss or misreporting ranges, and then field validation with representative assets.
What are the matters to be verified prior to deployment?
Select the representative assets of different materials, size and storage, to test read-or position effects; then check the impact of shelves, walls, equipment and personnel activities on wireless signals; and finally validate the points of the inventory, move, access areas, etc. according to actual business processes, and confirm that labels are replaced, charge or fail-processing methods. The selection model should not be based only on individual device indicators but also on installation, software interface and daily maintenance.

Ms. Lei
Mr. Pang