How to conduct periodic asset counts? Cycle management and data application
The key to a regular inventory of assets is not how many people are invested in one time, but rather the mix of "cycle management" and "data application" -- which allows the count to move from passive response to a controlled routine, and data that makes each count a basis for decision-making, rather than an overstep. Usually, manufacturing or circulation enterprises with a size of more than 200 people run as "quarterly + monthly draw + annual big disk" and cover most asset management scenarios.
Point 1: Align the different inventory cycles by asset value and frequency of change
All assets are divided into A, B and C categories by amount, morphological stability and frequency of use, which is much more efficient than "one-size-fits-all " .
Class A: Equipment costing more than CNY 50,000 per unit, equipment accounting for a large share of annual depreciation, and primary production line machines. Sample 10%-15% monthly and do a full count every six months. Class B: Tools, office equipment, and circulating stock items costing CNY 5,000-50,000 per unit. Sample quarterly and do a full annual count. Class C: Low-value consumables and office supplies. A 20% year-end sample is sufficient.
After the grade, the inventory resource will naturally tilt towards category A. When a plant that works on electronics puts the sticker, and when high-value devices like the labeler are listed separately, the monthly count time is compressed clearly, and the difference is reported to be lower. This layer logic is also used in the project to build the base disk.
Element 2: Standardize the inventory process and remove actions from reusable lists
Dismantling a full inventory into three stages of "preparation-execution-review" and exporting the checklists that can be checked at each stage avoid confusion in the temporary search for people.
Preparation phase (3-5 days before inventory)
- (a) The release of the accounts from the asset system, which are to be removed from the inventory form by location and each of which is controlled by 50-80 records;
- The inventory forms pre-fill the asset number, specifications, location of storage, custodian and only "physical condition/quantity" for the inventory;
- Sweepers, stickers, spray templates are in place; assets with vague or dropped bar codes are pre-redged.
Implementation phase (general 1-3 days)
- (a) A group of two persons: one person to scan, one person to check the physical condition and take photographs;
- Assets not found are indicated as "to be located" and not directly treated as losses;
- The inventory is withdrawn on the same day and cross-sky supplements are prohibited.
Review phase (within 3 days of inventory)
- Differences over reconciliation, summary by category: surplus, deficit, to be located, abnormal status (inactivity, end-of-life pending disposal);
- (a) Individual credit losses exceeding the pre-set threshold (e.g. 100,000) are subject to special verification;
- A draft inventory report is formed, with asset-independent departments signing double-checks with finance.
Point 3: Stocktaking teams and responsibilities are divided, avoiding "everyone is responsible but nobody is responsible."
The majority of the inventory is based on unclear roles.
- (a) Head of the inventory (1): from the asset management department, responsible for overall progress, adjudication of disputes and eventual signature;
- (a) Inventory implementation teams (grouped by location, 2-3 persons per group): from the user department, familiar with the site and able to quickly locate assets;
- Data review team (1-2): from financial or IT, responsible for systematic entry, matching of discrepancies and reporting output.
The process of the document handover system established between the Executive and Review Groups - the data review teams do not accept oral data when the inventory forms are returned - will remain unchanged even if the inventory is rotated.
Point 4: Select the inventory approach, determining the accuracy of data collection
The inventory is divided in three broad categories, from low to high, and the enterprise may choose on the basis of an information base:
- Manual desk reconciliation: small microspecies suitable for less than 300 assets, with the disadvantage of being inefficient and leaky;
- Barcode/PDA sweep: Medium-sized enterprises of 500 to 5,000 asset sizes, single PDAs scanned 800 to 1,500 daily, data-real time retrieval systems;
- RFID Batch Read: Fits to 5,000 or more, or a set of assets in a stack (storey, archive), read hundreds of labels in seconds; individual RFID tags cost about $0.5-2 and require a trade-off of inputs.
For small and medium-sized enterprises with limited budgets, bar-code programmes are a more expensive option; if assets are scattered over multiple plant blocks or floors, they can pilot RFID in a given region before it is extended.
Point 5: The variance analysis is not just a loss, but a cause.
The variance analysis is often simplified to "the amount of the shortfall and the amount of the billing." This is a mistake.
- The amount distribution of the differences in accounts - whether they are concentrated in a particular class of assets or dispersed among multiple categories;
- Discrepancies are classified as causes - scrapped, uncollected, not registered, not updated for relocation of storage or loss of physical property;
- Accountability for differences — process gaps or lack of implementation.
In experience, for enterprises that have conducted their first regularized inventory, the balance is usually in 3-8% of the area, and can be reduced to less than 1% after 2-3 rounds of standardized management. If the balance is above 3% over time, it is generally judged as a process rather than an implementation problem.
Point 6: How do you use the count? Don't let the report lie in the drawer.
At least four uses are used to take an inventory of the true value at the application stage:
- Optimization of asset allocation: an inventory of equipment with a idle rate of over 60 per cent and long-term excess as the basis for redeployment or procurement;
- Depreciation and end-of-life management: reconciliation of accounts to update the depreciation basis in a timely manner to avoid long-term disconnect between assets and physical items on the books;
- Budget preparation: the inventory data is the basis for the next annual budget for asset procurement, which is not supported by an inventory and only refers to the previous year;
- Internal control compliance: Complete inventory and discrepancy processing records are essential underpinnings for audit and internal control inspections.
The risk of data breaking will persist if the inventory results are maintained manually by Excel.
Point 7: Systematize cycle management, not tasks
The most vulnerable reason for the asset count is "motion" -- it's a little bit of a focus, and then it's back to normal.
- Set the inventory schedule in a monthly template, for example, “The third week of each month is for spot counts”;
- The results of the inventory are linked to the use of KPI in sectors such as those with a loss rate of more than 2 per cent, and annual deduction points;
- The inclusion of time count in the sector budget gives the implementing department a motivation to work together rather than cope.
Asset management is on track when the inventory becomes "unusual" status.
Return to the opening sentence: "The core of the asset inventory is "cycles, data are useful." First, you match the frequency of the inventory by grade, then you use a standardized process to ensure that each move does not go away, and then you then sink the data into system inversion management. Enterprises with over 200 people in size, starting from the quarter, gradually transition to a monthly disk + annual large disk combination, which is a relatively high-value path. It is recommended that, starting next quarter, they run all A assets once, then expand to B, C.

Ms. Lei
Mr. Pang