How do RFID asset identifiers be designed? Coding rules and label selection
The RFID asset identifier design, the first step being not to pick a label but to set the code rules to death. Fields are divided and length enough so that subsequent business adjustments do not push back and forth.
Point 1: Code rules are most useful in "striped"
A number of projects are starting to replicate the GSTIN or GIAI structure in the EPCglobal, and it turns out that the field of their assets is not right, and it's difficult to keep them as hard as a label. The more stable approach is to use the code as an address structure, organized by scene.
- Headmark(4-8 bits): Distinguishing one size, container code, position code for the first filter of the system layer
- Organisation(8-16 bits): a section of the UCC or a self-defined regional code within the company
- Category of assets(4-8 bits): e.g., equipment, tools, office
- Asset classes or models(4-8 bits): to SKU or specification
- Water Stream(overplenated): It is recommended that at least 2 20 or more number spaces be left to avoid depletion after two or three years
- Verify(optional): A set of 10 or similar checks in the application layer for the use of manual entry of dirty data from the bottom
The UHF tags (working band 860-960MHz) contain 96 or 128 bits of EPC. It is recommended to keep the total number within 96, leaving the rest for subsequent expansion or private manufacturer fields.
Point 2: Label selection frequency, chip, sealing.
Frequency determines the use of scenes
UHF (ultra-high frequency) provides long-range batch reading and is the first choice for warehouses, production lines, and outdoor assets. A fixed four-channel reader can achieve an 8-10 m read range with a clear line of sight. HF (13.56 MHz) requires close, aligned reads and performs well near metal, so it is better suited to enclosed spaces such as tool and file cabinets. LF (125 kHz) penetrates obstacles well but has a very short range, and is mainly used when retrofitting legacy equipment for compatibility.
Chips affect reading and writing sensitivity
In the same range, a higher sensitivity chip can read one to two metres more. For example, Impinj Monza 4 series, Alien Higgs 9 series, NXP UCODE 8 industrial chips are more stable in a dense stacking scene. The selection of which is also based on the reader compatibility and inventory cost, not just the parameter list.
Encapsulation is determined by the asset environment
- Paper is dry.: best value for money on plastics, wood and paper packaging
- Anti-Metallic Tags: Inner suction material or special antenna structure, which metal cabinets and steel pipes must use
- PCB Hard Marker: High temperature resistance, anti-corrosion resistance, common in industrial equipment and outdoor assets
- Soft Anti-Metallic Label: Specialized form of arc assets, such as contoured and condensable tubes, arc shells, etc.
For the level of protection, the normal storage scene is at least IP65; an outdoor or chemical workshop suggests a reference to IP67 or IP68. The work temperature range is checked, for example, the type of -40°C that is selected in the freezer.
Element 3: Match placement with the polarization direction of the reader
A tag is not necessarily readable just because it has been attached. On warehouse inventory projects, about 30% of missed reads come down to tag placement. Here are some engineering details that are easy to overlook:
- At least 3-5 mm gap between metal surfaces and labels, or directly anti-metal labels; reading distance may fall to one third of the original or not read at all if the gap is insufficient
- Liquids are clearly absorbed into the URF signal, and liquid container assets need to label it far from the surface of the liquid.
- Handheld readers are mostly linear antennas, labels are in the same direction as the antenna main polarization, or there will be a significant loss of reading efficiency
- A door-channel reader is usually a Circumpolar antenna that is less sensitive to labels and more suitable for free-pass asset counts.
The same type of asset is uniformly fitted at a height (e.g. 1.5 metres above ground) and directed, with the key points written into SOP, which usually more than doubles the efficiency of the inventory.
Point 4: Several pits repeatedly stepped on in the project
The position at the top of three is "right" and this section says it's easy to flip over:
- The coding space is too tight.: Early on, using 10,000 asset-planning fields, which actually expand to 50,000 after two years, the number space is depleted and re-labelling costs are higher than they were at the start
- The metal or liquid asset is labelled as ordinary.Paper-free tape on metal trays, with a typical success rate of less than 30 per cent and easy to pass the project through to acceptance stage
- Reader and tag bands are not aligned: The reader works at 915 MHz, while the labels buy 866 MHz band models (which often appear in cross-border procurement), which result in reading time and not being readable, debugging for long periods of time without finding the root cause
- Paste process is not standardized: The same asset has been labelled or labelled in an irregular manner, the inventory data is not correct and the final return to work
These pits have been encountered more than once in the field. Shanghai-based Chettech's approach is to make three separate deliveries of code rules, label selection forms, and SOP, which will be matched with clients for bulk purchases and construction, minimizing the cost of remediating at the site.
The RFID asset identifier is a simple, actually detailed, activity. The code rules determine whether to expand, the label selection type determines whether to read, and the installation specifications determine whether to read. It's not difficult to do all three things right, with an inventory accuracy of over 99%. First, the rules and data are clear, then next, the procurement and construction are relatively secure paths.

Ms. Lei
Mr. Pang