How the rfid storage management system solution is designed, label selection and implementation steps
RFID Knowledge

How the rfid storage management system solution is designed, label selection and implementation steps

PublishedShanghai Zejie Smart Technology Co., Ltd.

If a RFID storage management system program can land, it can be seen at the earliest in the label test form. If only "empty box tags, static readable" are recorded, but is prepared to purchase whole-ware equipment on this basis, then stacking, mixing, forklifts continue through and out of the neighborhood remains unknown. The after-line rereading and back-work are often the result of these undisclosed conditions.

The design should start with the most difficult-to-identify material, the busiest intersection and the most likely accounting ambiguity. This paper focuses on engineering implementation: how to define identification units, validate labels and attachments, limit reading areas, design data paths, and what evidence is used to determine whether or not to expand deployment.

First deliver an object-action-point confirmation map

First, following the receipt, temporary storage, mass examination, up-stamping, filling, pick-up, exit and return to the scene, record the object of each action and the conditions for completion. For example, a receiving site may verify the box, move the identification tray within the library, remove the single piece of work. Three locations do not necessarily use the same labels, nor does it mean that every reading point is subject to a change in inventory.

The research should output the number of objects that are current, typical packaging and loading, traffic routes and peaks, existing system duties, non-interrupted operations, and abnormally converted locations. Only the size of the warehouse can be estimated, and it is easy to miss the conditions for real impact effects like two adjacent corridors, piled up by the door, forklift re-entry.

The cycling tray label usually identifies the vehicle itself, and loads and quantities change in the system; a single-time box mark can follow the container, but when unboxing, packaging and returning is required to define whether or not the original identity is retained. When multiple labels are used for the same package, clear rules of mapping and counting should be established, otherwise coverage increases, and physical numbers may be repeated.

Label selection is excluded: not applicable first, then compared performance

First round of viewers and environment.Normal paper boxes, metal utensils, liquid containers and low temperature decomposition packagings, cannot be directly shared with the conclusions of an empty-load test. First column materials, contact surfaces, moisture, washing agents, friction, bending and recovery requirements, re-scanning label structures, outer casings, glue or mechanical fixes. If you must be cleaned during your operation, the test also covers the after-clean adhesion and readability state, rather than checking only the shell's promotional parameters.

Second round of wireless match.Consider passive UHF for reading in bulk in a warehouse, but match readers, antennas, and tags to the frequencies and transmission conditions permitted at the deployment site. Suitability of other frequencies or near-field methods depends on range and how users interact with tags. HF is not inherently immune to metal, and datasheet range is not the same as dynamic range under full load. [1]

The third read code and bind.The information must be placed on a label first, and the information must be checked from the back. It is usually possible to identify the associated commodity with a stable object, batch, cargo owner and business status, so as to avoid expanding storage needs in order to insert all fields into the label. When using GS1 markings across enterprises, the numbering should be assigned and coded according to the applicable coding rules; an internal custom number cannot claim that it has been compatible with some type of GS1 identification program simply by entering the EPC storage area.[2]

Print, write code, read back and bind objects to a verifiable operation. Barcodes and RF values can be expressed in different forms, but must be deciphered to the same object; "Chip has a number" does not mean that business binding has been completed. The site also needs to specify how old labels are disabled after re-taping, so as to prevent two still valid identities from being found in a physical object.

Where are the labels?

There is no "unique top right" corner for all goods. The adhesion position requires consideration of the bet, the direction of the antenna, the swing wear, the packaging damage and the artificial visibility. The same box may not have the same result when plastics are empty or metal parts filled; the swinger box is directed to a fixed installation point, which is different from any artificial stacking.

Test Variable Actual conditions to be covered at least Records and judgements
Load Status Air, typical full and least-favourable; in the case of multiple inner packagings, they should be tested separately Read the results by object, not just "Current success"
Append and face. Candidate installer, permitted rotation direction, tab spacing and mask Finds enforceable installation specifications and marks prohibited locations
Access Real speed range, stopover, reverse, two successive trajectories and permitted deviations Record automatic capture, repeat events, error of direction and unusual working hours
Non-target audience The next door passes, the door is still open and people carry labels. Distinguishing from the current business when you read a neighborhood label
Life-cycle conditions Project agreed cleaning, cooling, friction or reprocessing conditions Check for appearance, fixation, writing binding and reading changes separately

Each round of tests retains the label type and batch, sample object, reader and solids, antenna position, power, parameters, pass-through process and original record. Only by changing a planned variable can you distinguish between improved performance from an installed location or temporary result with higher power at the same time. Samples and repeat times should be agreed on risk; a small number of state best presentations cannot be extrapolated to long-term operational capability.

The goal of the tunnel design is to read the boundary, not to make it so far away.

A pick-up point should define access, identification, review, exiting the operating window and specify which objects outside the reading area can never be counted into current operations. Depending on the field need to be covered by a combination of antennas, limit the distance, trigger the signal, necessary isolation and mission context. The light trigger is appropriate for time sequence evidence, but directional judgement still needs to be combined with validated logic, not to default a single trigger to represent that the library has been entered.

The RSSI can be a certified auxiliary feature, and cannot act as a remote-foot or direction sensor alone. Goods that are permanently parked at the door, metal structural reflections and the working methods of adjacent equipment need to be included in the same field test.

The number of antennas cannot be applied to the "Four or more collision-resistant" rule. The response between labels is handled by an inventory and collision-proof mechanism of air protocols, interference between readers, and other problems are the way in which equipment antenna ports are switched.[1] Specific equipment capabilities should be checked, queries rotated and trigger configurations should be tested for stability at multiple points of simultaneous operation; additional antennas do not automatically increase business channels that can be delivered independently.

Fixed channels, handheld terminals and forklift-mounted readers have the same boundary. If you are just a intermittent cycled drive, it is not necessary to lay an antenna on each shelf. If you are moving to collect, you also need to indicate how the location of the library is confirmed: read in the vicinity does not mean that it is located at a specific space, let alone read the normal label and package it into continuous precision.

From radio frequency reading to inventory confirmation, at least three records are kept between

Original Read RecordIndicates which label is read by which device or antenna at what time. It helps to diagnose coverage and anomalies, but the same label produces many readings, not a number of physical quantities.

OrganisationThe type of process that you can use to read in the context of this task and the area, to solve the object, to aggregate the time window, to expect a group check, etc. The label is not part of this list, the tag is unknown, there is no direction evidence or the object is not out of the reading area, which can be the reason why it cannot be automatically confirmed.

Business recognition recordsThe system that is clearly responsible for the inventory is created, documents that are recorded, objects that are completed with what results and how inventories are changed. GS1 EPCIS can be used as a reference for event symmetric design; it remains operational to define what evidence is sufficient to complete receipt, transfer or exit.[3]

The equipment access layer is also made clear. Gen2 describes the air interface between the label and the reader; LLRP is an interface between a reader and the client, which cannot be replaced by one another.[1][4] Projects may select the manufacturer SDK or other supported interface, but it needs to be clear whether configuration can be restored after breakup, data formats are stable, and who is appropriate for replacement of the device.

Implementation level: No expansion of procurement without evidence

Level one: Sample validation, locking in a viable combination

The labels and candidate installation point tests are done with representative materials, which form the list of applicable and non-applicable. This stage is not "select a chip " , but rather determines the labels that a certain material can use under the agreed conditions, attached, read points and parameters. Materials that do not meet the requirements should be shown as separate readings or substitute for the collection process.

Shutdown two: the smallest business closed loop. Check if the account is really moving.

Select a representative business chain, from initialization, receipt of goods, up to the exit bank, and then re-entry or revocation. The pilot range is determined by key risks, without having to mechanically limit an area. The acceptance depends on whether the target can capture it, but also check the unknown label, wrong batch, unwinding zero, and how to deal with the failure to report and access.

Close three: failure and simultaneous exercise to check for recovery

Simulation interface response lost, equipment offline, services restarted, adjacent access and back-up event. Special check "business confirmed, return not yet returned": Retry should follow the same operational identifier and return to the already existing results; physical movements that cannot be identified during a break-off should remain unverified and should not be assumed to succeed by direct timeout.

The same load is a legal business, which returns in the afternoon. It must have its own identity; duplicate requests for the same task need to be avoided. The scope of weighting and retention period should be included in the interface agreement.

Checkpoint 4: Roll Out in Batches by Material and Workstation

When the pilot conditions are met, then it is extended to similar situations. For each new packaging, package or hand-over, the test conclusion is confirmed that the original test conclusion is still valid. Toggle by agreeing on a baseline for inventory, and not completing document processing and backtracking; old and new processes cannot be recorded in one copy of the same receipt and dispatch.

Receiving and inspection reports and maintenance desk accounts should be able to explain the change in performance

The report presents at least the first automatic capture separately, non-target error inclusion, manual reading, business double confirmation, complete operation time and abnormal recovery. Target thresholds are determined by test and operational risk, not a static read rate for full-scale dynamic operations. Compared with manual processes, the same loads should be used, the same tasks and similar operating conditions should be used, and the unusual processing time included.

The maintenance does not read and write only online. The result can be changed by de-labeling, changing materials in the box, moving shelves, shifting antennas or modifying parameters. The equipment and parameter version can be recorded, installation location, abnormal type and place of work; the label batch is replaced, the placement or updating of solids is adjusted, and the affected scene is returned to the test. The frequency of the inspection is based on wear and tear and risk setting, and the quarterly inspection cycle is more reasonable than the fixed monthly check.

The final project should leave reusable engineering information: object and business maps, label test matrices, reading areas and installation maps, coded binding rules, interfaces and status statements, abnormal testing records and maintenance liability lists. Software interfaces can be similar, but this information must be stored in actual storage; they determine whether the system is expanded, equipment replacements and the continued reliable operation of the facility when dealing with anomalies.

Technical reference and scope of application

[1] GS1, EPC Radio-Frequency Identity Generation-2 UHF RFID Standard, for passive UHF over-the-air communication and inventory mechanisms; [2] GS1, EPC Tag Data Standard, for tag data and identifier encoding; [3] GS1, EPCIS Standard, for representing business visibility events; [4] GS1, Low Level Reader Protocol Standard, for identifying device integration interfaces. This article offers an engineering design method and assumes no uniform read range, tag price, schedule, or warehouse-wide read metric.