What kind of RFID asset management equipment is there?
The RFID asset management equipment consists of three main components: an electronic label on assets, a reader for data collection and associated antennas and management software. The UHF (UHF, 860-960 MHz) is most used in the domestic asset inventory scene, with typical distance of 3-8 metres, which allows for the identification of hundreds of tags in bulk at a time; a high frequency (HF, 13.56MHz) is suitable for accurate reading at close range. Readers are morphologically fixed and handheld, the former is used for exit and exit, the passper is automatically collected, and the latter is used for manual inspection and dispersional points.
What is the main component of RFID asset management equipment?
A running RFID asset inventory system with hardware layers that do not fit the following categories:
- Tag: There are three types: passive, active and semi-passive. Passive tags are the standard choice for asset inventory. They typically cost CNY 0.5–3 each, have a long service life, and are powered by the RF energy emitted by the reader.
- Reader: Also called a reader, responsible for the launch of radio frequency signals and the receipt of tag returns data are the most easily pedaled loop in the selection.
- Antenna: Fixed-readers typically require external antennas, whose benefits and polarization determine the actual reading distance and overlay shape.
- Handheld Terminal: The essence is to integrate the reader modules, antennas and batteries, which facilitate manual inspection.
- Card Dealer: Small equipment that writes asset numbers to blank labels.
When we do our work on the storage and machine room projects, we usually match the type of asset with the client, take an inventory of frequency, then reverse the equipment list -- like the plate in the cabinet to be finely identified, and the antenna that the whole tray goes into and out of the library, power, label type.
What about fixed-readers and handheld readers?
The choice of the form depends on whether your assets are "moveable" or "basically still", and whether the count is "passway" or "package-by-part".
Fixed ReaderUsually, it is a door-barrel, top of the shelf or line, and it covers a fixed identification area with antennas. The advantage is that no one is on duty, automatically collecting, suitable for warehouse entry/exit, archives, where such assets pass through fixed points in the tool compartment. A four-legged fixed-reader price is between 2000 and 6,000 yuan, and it's more expensive at the industrial level (IP65 protection, high temperature tolerance).
Handheld ReaderMore flexible, the inventory clerk can read in bulk by walking around the shelf. Fits for equipment rooms, office areas, libraries, which are scattered and not easily equipped with a secure door. Price ranges are larger, consumption levels (based on Andrey) range 3,000-8,000, industry three-default (1.5 metres down, IP65) usually at 8,000-20,000.
Many of the items in the exercise are a combination of these: a fixed access to and from the entrances for real-time entry and exit, a full inventory of the quantities on a regular inspection by hand and a consolidated asset desk account in the back-office software for both sides.
What about HF and UHF readers?
The RFID asset management scene in the country is a major source of information.UHF (UHF, 860-960 MHz)Read distance, can be controlled and can be read in bulk.
- Unsourced labels associated with 4dBi antenna: 3-6 m
- Unsourced labels associated with 8dBi ' s high-benefit orientation antenna: 8-12 m
- Source label: 30 m or more
HF (HF, 13.56 MHz)Reading distances generally do not exceed 1 metre, but the metal-resistant and liquid environment is better suited for one-on-one reading on small items of assets (tools, instrument attachments) and is often used in such settings as archives management, human door closures, etc.
Three factors are considered when selecting the frequency range: the material of the asset (the metal surface is to be flexible and resistant), the density of the inventory (the shelf is heavily selected for UHF, which is controlled by the antenna orientation) and whether it needs penetrating (UHF has limited penetration over a dense stack).
How does the reading and writing power match the number of antennas?
More reader power is not always better. UHF RFID transmit power is regulated in China, generally at ≤2 W EIRP depending on the band and region. Excessive power creates compliance risks and can cause interference between tags, resulting in missed reads.
Common configuration reference:
- Channel type (2-3 m wide): 1 reader + 2-4 round-polar antennas, 6-8dBi
- Plasma rack (1-2 m per floor): 1 multi-literate reader with 1-2 flat ceilings per layer
- Large space inventory (handheld): handheld terminal with antennas within 1W of power
An antenna chooses whether it is round or line polarized, depending on whether the asset is fixed in its direction. A Circumpolar antenna is not sensitive to the label towards its direction (suitable for a scrambling), but reading distance is shorter than the line polarizes; and the polar antenna is more valuable, but the label must be set up.
What's the layout?
Survey the site before deployment. Confirm the locations of reflective metal surfaces, sources of electromagnetic interference, and power and network connection points. Metal reflects RF signals and creates multipath effects that can cause missed reads. Variable-frequency drives, high-power motors, and Wi-Fi base stations can all interfere with the UHF band.
Typical deployment steps:
- Draws an asset animation line: the path through which the inventory of a person or forklift will pass, and the fixed reader is installed at the nodes of these paths.
- Antenna height and angle: 30-50 cm above the general shelf, 15-30 degrees down in a tilt to avoid positive face to metal.
- Pre-encumber cables and interfaces: Readers need web lines (PoE power more economical) or Wi-Fi back, with antenna feed as far as possible within 10 metres (sign decay).
- On-site testing: read rate measured after tagging, target tha 99% single reading.
We did a machine room project, where we first put the readers on top of the cabinet, and the drop rate was significantly high. Turning to side-slash, the reading rate went from about 85% to over 99%. It's not clear that this is not actually going through it.
How do we receive and receive after deployment?
The acceptance cannot be based on the reading and writing of data, depending on three hard indicators:
- Read Rate: First-pass tag identification success in normal operation. A common industry benchmark is at least 99%.
- Error Rate: The label should be placed outside the given area and the reader should not read it, usually requiring 1%.
- Stability: Does data completeness fluctuate after eight hours or more of continuous operation?
Also, to confirm whether the back-office software correctly interprets the original reader data into asset events, including access, departure, inventory, etc. When you check and receive a client, Shanghai-based Chettech will run a test list of typical scenes, comparing them with expected and actual results, ensuring that no repeated reference is required after the system goes online.
What are the most common pits in selection and deployment?
Several high-frequency pedal sites deserve to be avoided in advance:
- Neglect of asset material: The normal paper label is barely read on the metal cabinet and must select a metal-resistant label with suction materials at 5-10 times the unit price.
- Reader interfaces are not fully available: many projects have only a web line and no antenna position is found when late on the Wi-Fi or 4G extension.
- Ignore label installation: When the labels are placed on the side (cylinder pipe, spherical device), the reading distance is reduced by 30% - 50%.
- The protocol is wrong: some readers support only private agreements, and must confirm in advance whether back-office software (WMS, EAM) is available.
- Ambient temperature: Below -20°C or above 60°C, the sensitivity of standard industrial readers drops noticeably. Choose a wide-temperature model.
The equipment threshold for RFID asset management is not high, but to be stable and data available, one point at a time from label selection to the reader layout. It is recommended that small quantities be measured before procurement, and then batch configurations and suppliers are determined. When budget limitations are limited, priority is given to quality of readers and labels, antennas, feeders, and installation can pick up high value-for-money items within the range available.

Ms. Lei
Mr. Pang