Is the rfid tag safe from theft?
The RFID label is protected against theft, but only if the system is deployed. The RFID alarm is not about "it will be" in nature, but it's about the antenna at the exit that triggers a alarm when it reads "uncollected." This logic runs for years at retail openings, clothing doors, book stores, but it's not all-powerful -- metal masks, liquid environments, labels torn apart, antennas to blind areas, and it can make them fail.
Point 1: RFID is on the EAS. The label doesn't make a sound.
Many people think RFID has a beeper in it, but they don't.EAS (Electronic Article Survellance, electronics commodity surveillance)The mechanism, specifically an EAS position (also known as ESA flag) defined in the Gen2 protocol. This is a default state when each label is out of the factory, and Zreader will change it from "unsolved" to "liquidized", and exit door-barrier antennas are continuously scanned, and if there is still a tag EAS position in "unsolved" status, the sound light alerts.
The key here is "actively rewriting." The difference between RFID and the traditional RF/AM hard label is that: one step in closing a booking and unlocking, without the need for shopkeepers to tear up a tag or demagnetics. When we do our programs for Shanghai-based technology clients, POS and readers usually have to make a link that's a priority, otherwise the EAS position will not change, and the alarm will be triggered by mistake.
Point 2: Three typical deployment patterns of RFID against theft
Form A: Soft tag scheme for pure RFID+EAS
This is the most mainstream scheme in retail trade. The label is a regular RFID non-dry glue, put on a commodity or a chandelier, and the reader recasts the EAS at the close of the book. The advantage is to hide, not to affect packaging; the disadvantage is that the label will be disabled once it has been torn or torn.
Form B: RFID Hard Tag Program
It's common in clothing, shoes. The label itself is a plastic shell button, which needs a special lock-opener to remove. The RFID and the mechanical structure also perform a burglary function, and tearing off the button triggers alarm. The advantage is that physical damage is difficult, the disadvantage is an increase in the cost of individual products.
Form C: Integration of RFID with traditional EAS
Some of the stores have been superseding RFID reading and writing on the basis of the original RF/AM hard label, such as the dressroom, the precious goods area. Shanghai has used this blending in several clothing chains, with RFID taking stock and ESA, traditional RF hard tags as the last line of defense.
Point 3: The real scene of RFID's theft.
From engineering experience, the following types of scenes have stabilized:
- A clothing retail shop.: For moderately priced, midsize items with a controlled checkout process, RFID plus an EAS bit can keep missed alarms very low. According to retail case studies published by the RAIN Alliance in 2023, stores using RFID and EAS reduced inventory discrepancies from the industry average of 1.5–2% to 0.3–0.5%.
- Books, stationery, cosmetics: The label can be placed on a laminate or under seal, metal and liquid interference is small, door-ban antennas are stable.
- Storage and door shop integration:: The warehouse exit and door shop security is shared with the same labels, reducing the cost of double-marking.
Common to these scenes are: individual items with overpack or plaque, standardized billing actions and relatively fixed export locations.
Point 4: Several cases in which RFID can be ineffective
There are no silver bullets. The following scenarios, which will significantly reduce the RFID's ability to protect against theft, suggest that they be evaluated in advance:
Boundary 1: Metal and liquid environment
In extreme cases, a door-to-door antenna may not read the label at all and naturally do not trigger an alarm when RFID tags in the UHF band (860-960 MHz) are placed on the metal surface or on a liquid container. If the goods themselves contain metals or liquids (e.g. cans, bottled drinks, hardware tools), either on-metal tags, or switch from RFID to traditional AM/EM hard labels.
Boundary 2: The label is physically damaged or concealed
The undry glue tags are torn, inlay's antennas are cut, and hard-labeled buttons are removed from the table. In the dressroom trial room, "torn high-fast area" near the cashier, this is the main source of underreporting.
Border 3: Banner antennas cover blind areas
The closed antenna is usually installed on both sides of the exit, 2-4 metres away, with a width of about 1.5-3 metres (depending on power and label gain). If the customer passes quickly, closes to the edge or uses a shopping bag to shield the tag, the reading/writing success will decline. The empirical value is: single label, two-way through, speed below 1 metre per second, recognition is usually above 99%; speed exceeds 2 m/s, or multiple people line up, drops significantly.
Border 4: EAS bit not rewrited in time
The failure of the POS system to access a reader, the unreseting of the return label, the trial of unmagnetics, makes the "liquidated" label subject to an embargo on doors and leads to false reporting. Over-reporting causes the shopkeeper to create a "wolf coming" mentality, ignoring the real alarm.
Boundary 5: Difference in frequency and standard
The reading and writing distance of the HF (13.56 MHz) and LF (125kHz) labels is usually less than 1 m, and a much more dense antenna array is required for door-to-door coverage at a higher cost than the UHF program. If the commodity is already using an HF tag (such as the NFC payment scene), the security antenna needs to be deployed separately.
Element 5: Several key parameters when the project landes
If you are evaluating the RFID piracy programme, it is recommended that priority be given to verifying these parameters, which are more effective than simply comparing equipment prices:
- Door-free antenna power and width of coverage: The typical EIRP of the UHF-Cunt antenna can be adjusted in 1-4W ranges, corresponding to a width of 1.5-4 metres. The greater the power cover, the wider it is, but also the local radio management requirements, such as the limited power of the Chinese SRRC for the UPDF RFID launch.
- Tab SelectionThe normal inlay unit price is $0.3-1 (Kin RMB), the anti-metal label 2-5 and hard tag 5-15. Retail scenes are more often used as inlay+ chandelier programs.
- POS interface: POS triggers reader to recast the response time for the EAS position should be contained within 200 ms, otherwise there will be congestion during peak closing periods.
- Alert strategy: Only the sound alarm, or the connection door ban, or the connection surveillance video? When serving a book chain, Shanghai Jiechi pushed the alarm signal to both the owner's phone and the counter screen, with the leaking response time from minutes to seconds.
- Baseline of the misreporting rate: The misreporting rate for the first two weeks after the go-live is recommended to be below 0.1% (by human count), otherwise it would require an antenna power shift or a check of EAS position rewriting processes.
And to summarize: RFID can protect against theft, and in retail settings, clothing, books, etc., it's been repeatedly verified. But it is only if the EAS-bit mechanism runs, the door-barrel antenna is covered, and the label is not physically damaged. The metal liquid environment, which is fast through, the EAS-bit has not been rewritten, is its four main invalid borders. The selection gives priority to the match, then to the equipment parameters, which are more than just price.

Ms. Lei
Mr. Pang