Tray rfid electronic tag selection and cargo flow data acquisition program
Many people think that RFID electronics are the same, and read it with one single label, but the tag on the tray is to hold a forklift crush, forklift impact, condensation, cold heat alternation, and be identified in a dense stack. The selection is not in place, and cargo flow data is empty. This article is in the order of "Fight to Deep" and explains several core principles of the RFID selection -- why can't you reset the normal tag, frequency, chip, how to pick, how to deploy the reader and antenna, how to transfer data from label to backstage system.
The label on the tray. Why can't you copy the regular RFID tag?
The design goal of the general commodity-grade RFID label is "on a box, once in a cashier's pocket" and there are significant differences between the use of the scene and the tray tag:
- A pallet tag typically stays on the pallet for three to five years, substantially longer than an item-level tag;
- Trays are often stacked on 6-8 layers in the warehouse and labels are read from the antenna from the side, bottom or top rather than from a single piece;
- Forklifts are easily labelled by forklifts, which are damaged by a fall or drop of the fork and have a high temperature range (refrigerator as low as -25°C and platform at over 60°C in summer);
- Metal trays or metal shelves reflect frequency signals, and general labels are almost unreadable.
So the tray labels have to take into account four dimensions at the selection stage: physical strength, electrical performance, installation, environmental adaptation. None of these four points is off, and the expensive reader can save the data.
Frequency, chip and seal: three core variables for the selected type
Start with frequency. Pallet-level RFID almost always uses UHF, operating at 860-960 MHz and conforming to ISO 18000-63 and EPC Class 1 Gen 2. LF (125 kHz) and HF (13.56 MHz) read ranges are too short, generally under 1 m, for pallet applications that often require 5-15 m.
The chip determines the size of the label, reading and writing speed and security features.
- Impinj Monza series (e.g., Monza 4QT, Monza R6): 96-128bit in the EPC area, which is more sensitive to read within the plant and suitable for intensive reading;
- Alien Higgs series (Higgs 3, Higgs 4): a larger 512bit user storage area suitable for the scene where custom data need to be written in the label;
- NXP UCODE series: The encryption and forensics are highly capable of being suited to the pharmaceutical and tobacco industries, which require protection against hypocrisy.
Monza R6 or Higgs 4 is sufficient for standard warehousing, at 2–5 yuan per tag. If you need to encode additional data such as batch, expiry, or origin, choose a chip with at least 512 bits of user memory.
The most visible part of the tray label is a cover.
- ABS hard-shell label: shock resistance, IP protection levels usually IP67/IP68, suitable for a high outdoor or forklift operation, at a unit cost of $8-25;
- PCB hard labels: 5-15% lower than ABS, good metal resistance and suitable for metal trays;
- Ceramic labels: small size, high temperature tolerance (up to 200°C) suitable for special process environments;
- Soft anti-metalinlay: It can be placed on arc or not flat surface, with the lowest cost but short life.
It needs to be emphasized that the metal tray must be labeled "anti-metal design" and, essentially, there is an iron oxygen at the bottom of the label antenna or a suction material for isolation. Normal ininlays on the metal, reading distance falls from 8 meters to less than 1 metre, and there's something weird about "landmarking without reading."
Reader and antenna: How do you get it in the warehouse?
The label is right, the reader and antenna are not deployed, and the data acquisition chain will be broken. The RFID deployment in the warehouse usually takes three forms:
- (a) Gate-style reading and writing channels: 2-4 antennas, around symmetrical set to cover the full extent of the passage, suitable for the automatic inventory of access to and from the warehouse;
- (a) An antenna on top of the stacked area: on the top or side of the shelf, covering the entire alley or stacked area and suitable for inventory count;
- Handheld terminals: used for abnormal processing, drawings, search of specific trays and reading distance of 3-5 m.
Several parameters at the level of exercise should be stuck:
- Transmit power: China's UHF regulations limit effective radiated power to ≤2 W ERP. Higher power can interfere with other equipment;
- (a) Arctic polarization: a circular polarized antenna is not sensitive to labels in the direction and is more suitable for a dense stacking of trays; a line polarized antenna has a slightly long distance to read but is sensitive to orientation;
- (a) Read rate: 100-300 labels per second for the reader supporting Gen2 protocol and 10 trays with access to the channel will not be lost;
- Collision-resistant algorithm: Priority is given to equipment supporting intensive reading and writing patterns, with multiple readers working without interference.
A common example: one consumer goods warehouse had aisles 2.5 m wide and pallets stacked 1.8 m high. Shanghai Zejie Technology Co., Ltd. installed two fixed four-antenna readers facing one another. Each had a read radius of 4–6 m, covering the entire aisle so forklifts could be read without slowing down. That was the key requirement for keeping operations moving.
How are cargo flow data transferred from labels to backstage systems?
Many projects have left the hardware here, and data is not available. The complete cargo flow data link contains at least four layers:
- Sensory layers: the label is read in antenna, and raw data include the EPC, TID, reading time stamp, reader ID, signal strength RSSI;
- (b) Marginal layer: RFID intermediates are filtered for data - the same label is only kept once when it is read by multiple readers, and error is removed from the list of serial readings according to rules;
- Transfer layer: the middle is pushed backstage by MQTT, HTTP, Socket etc.;
- Application layer: Data enter WMS (storage management system) or ERP, bind business fields such as tray numbers, cargo owners, SKU, batches, time for storage, generate visualized reports and retroactive records.
The most problematic is the edge layer. The same label in the warehouse can be read many times through a channel antenna, stacked antenna, and the moon antenna, where if data are not weighed down, there's a weird phenomenon in the business system of "a tray being stored three times." One lesson is: the middle piece is to be reweighted on an EPC + time window, which is set at 3-5 seconds.
Also, label data are bound to the owner's data. The common practice is that when the tray is first entered in the library, it is used to scan the tray numbers and labels with a hand-held terminal, and to write them to WMS, and the later read the EPC through a map sheet to find the tray number and then find the goods. If you skip this step, there is only one line of 16-inch code that you can't understand, and business is not working at all.
Several speculations and deployments of permafrost pits
- The metal tray forgot to select the anti-metallic label and the whole series was invalidated;
- The freezer operation selected the normal ABS label, with a crack in the shell below 20°C;
- The tunnel antenna is placed in the middle of the door frame and metal containers block the side-to-side label when the forklift passes, leading to a missing reading — the antenna should be installed at or tilted 15-30 degrees;
- The reader power is maximum, and the labels are read in a series to the next channel - the power is adjusted to the width of the channel;
- The tags are not mapped with the EPC and tray numbers after they have been written.
The RFID is not "a label is a complete chain" from the physical properties of the label to the flow of system data. Clear these core principles, the program design will not be missed. If you can't see which type of labels to choose in the project, how Zreader should be clothed, you can send us the size of the warehouse, the type of tray, reading the scene, and you can look at how it actually landed.

Ms. Lei
Mr. Pang