Application of flexible anti-metal rfid labels, installation and selected care
RFID Knowledge

Application of flexible anti-metal rfid labels, installation and selected care

PublishedShanghai Zejie Smart Technology Co., Ltd.

Answer the most common question: Can't you read it on RFID labels?

A lot of people first come in touch.Soft anti-metal RFID label, the first reaction is often, "Doesn't RFID fail on metal?" That is true for standard RFID tags, the familiar passive UHF type. On a metal surface, their read/write range can plunge from meters to centimeters, and they often cannot be read at all. The problem is the RF signal itself: metal reflects electromagnetic waves and causes coupling losses at the tag antenna, so the tag cannot be activated normally.

The flexible metal-resistant label is a product designed to solve this problem. It adds a special layer between antennas and metals.EMPID Buffering MaterialAnd we'll have a nicer view of the structure of the antenna, so that even if you put it on the metal surface, you can read and write. The next floor is clear about how it works, where it is, what it is installed, and what it chooses.

Principle: Why are general labels afraid of metals and what do anti-metal labels do?

The RFID tag readers are essentially a reader that sends radio frequency signals, and the label antenna is then connected to the current, and then re-launchs the stored ID information. The metal affects the radio frequency signal in three main ways:

The core idea of anti-metallic labels is to insert a "buffer cushion" between the antenna and the metal. This layer of material is usually a high magnetic conductivity suction or a specific thickness insulation, which can bind the magnetic field created by the label antenna inside the label without making it strongly bound to the metal. The characteristic of soft anti-metallic labels is that they are thin, bent, so the overall thickness of the label is controlled at around 1mm to 3mm, so they can fit the non-standard surfaces of the arc, the pipe, the curved crust.

In frequency bands, the majority of flexible metal-resistant tagging on the market is in UHF bands (860-960 MHz, depending on country, China 920-925 MHz). Reading distances typically range from 1 to 10 metres, depending on label size, chip sensitivity and reader power.

Apply scenario: where it is really needed

Soft anti-metal labels are not "all-power alternatives" and have clear boundaries of use. In the light of our project experience, they are most appropriate in the following scenarios:

Metal packagings and swing gear management

The metal boxes that are common in factories, steel trays (the metal tray is a very large type of material used in storage), revolving baskets, tool cabinets, all fall into this category. A car spare parts factory needs to trace thousands of steel containers, each of which flows between different processes, traditional bar code + manual scanning is inefficient and makes mistakes. When you put a flexible anti-metallic label on it, you can find a mass identification with a channel reader, without opening the box.

Metal equipment and asset tracking

The room cabinets, electrical equipment, medical devices, outdoors, etc. are all metal casings. These assets are of high value, widely distributed and require regular inspections and inventories. Soft anti-metallic labels can be placed on the side of the cabinet or top asset tags, and they can be counted with handheld terminals.

Metal pipes and cable marking

Soft anti-metal labels can be attached along the arc of the pipe, replacing traditional spray code or branding.

Curved or alien metal shell

For example, metal tools, molds, cylinders, fire-fighting box doors, outdoor engine doors, etc., flat-level labels cannot be placed or evened and soft anti-metal labels can fit arc with low chorus.

What needs to be stated is that if the label is to be placed on very small metal surfaces (such as screw heads), or if the surface temperature of the metal is long longer than 80°C, or if the surface is often rubbed, flexible anti-metal labels may not be the preferred option, and there is a need to consider ceramic labels, plastic labels or special process sealing.

Installation: adhesive, tactful, embedded

The same label is installed on different surfaces, and its effects are much less effective.

Back-flip

The simplest way: to remove the ionized paper on the back of the label (i.e., the smoother protective film of the layer) and to place it directly on the clean metal surface.

Several key points:

One of the cabinet asset projects we did was a general backlash, which started with about 15 percent of the labels six months later. Then it was replaced by 3M industrial backwood, and it was almost undefeated when we checked. The difference came from the thickness of the gel, the temperature-resistance variation and the early viscosity.

Stick or screw-fixed

In an outdoor, industrial environment or when labels are frequently changed, it is recommended that the label be pierced at its four corners and fixed with a nail or screw. Note:

Embedded or Encumbered

Some scenarios require labels to withstand shocks for a long time, vibration or chemical corrosion (e.g., plating workshops, chemical feedstock drums), which is then embedded in the dent+ encapsulation (epoxy resin or silicate). The label is completely enclosed in the trachea of the metal surface, and only the surface shows up.

Hanging or tweezing

For objects that are not easily labelled, such as swing tools, metal slurry, you can tie a label to a metal rod or use a sticker to fix it with a hole.

Selective care: How to pick the right one

The following are the most interesting dimensions of the selection.

Read-outs requirements

First establish how far away the tag needs to read. At 1–3 m, such as handheld counts, a small, inexpensive flexible tag is enough. At 5–10 m, such as a warehouse entrance portal, choose a larger tag, usually at least 5 × 5 cm, with a high-sensitivity chip. Note that the manufacturer's stated range is usuallyThe best conditions in the lab.The data below are actually subject to metallic background, reading and writing power, environmental disturbance etc., and a seven-off estimate is recommended.

Size & Shape

The common size of a soft anti-metal label varies from 25 x 25 mm to 100 x 30 mm, or even can be made into strips, super thin card. Select the type to confirm the space available for tag attachment positions -- like the label slot at the door of the machine is only 30 mm wide, and then only within 30 mm width.

Chip Type

Common chips in the UHF frequency range are Alien Higgs series, Impinj Monza series, NXP Ucode series, etc.Sensitiveness(i.e. the weakest signal strength required for the label to be activated) andMemory CapacityDifferent. If only one ID is marked, the normal chip is sufficient; if more parameters (e.g. equipment model, date of production, inspection records) are required, it is recommended that a larger storage capacity be selected to support multiple writings.

Working environment

Temperature, humidity, chemical corrosion, ultraviolet, mechanical impact - among these five factors, as long as there is a tolerance range beyond the normal flexible metal-resistant label, special description and customization are required. For example, long-term outdoor sunbaths, the label face requires resistance to UV; plating workshops require acid-resistant alkalis; cold storage needs to be low temperature (up to -25°C).

Protocol and frequency band

Confirms the protocol (EPC Class 1 Gen 2/ISO 18000-63) and frequency bands that you use. If a project involves overseas, it is necessary to confirm whether the label supports the frequency band of the counterpart country (e.g. 902-928 MHz in the United States and 865-868 MHz in Europe).

Engineering capacity of vendors

This is easy to ignore, but it's critical. A mature supplier should be able to provide: real reading distance data on labels on different metal surfaces (e.g. stainless steel, aluminium alloy, zinc plating); printing/coding services (if field spray codes or pre-written ID are required); small batch sampling (generally 3-7 days); and tailoring programmes for special environments (high temperatures, outdoors, chemical corrosion).

At this point, we're...Shanghai Picking Up Tech Ltd.In projects that are exposed, suppliers are given priority to provide a visual reading distance curve on the surface of the target metal and to maintain data on the viscosity of the back tape at different temperatures.

Summary: Rewinding from demand, more stable than pushing from product to product

Soft metal resistant labels are not as expensive as possible, but the key is matching. Specifically, they can be pushed in the following order:

  1. Set the scene first.: on what metal, how far away to read;
  2. Re-establish installation: Tighten back, fixed nails or embedded encapsulation;
  3. Final Selection: Rewind sizes, chips, back-flip levels according to scene and installation.

If you are evaluating this type of tag, get samples of three to five models and compare them for a week under real operating conditions. Focus on consistency of read range, adhesion, and performance in the environment. Datasheet figures are only a reference. The project's success often comes down to details you did not expect on site.