How can RFID asset positioning management be achieved? Area identification and accuracy
Last year, more than 200 monitors and infusion pumps were scattered across over ten wards at a medical device client's hospital. Each monthly count took three people three days and often differed from the books. RFID location works by tagging assets and using readers to map the area where a signal is detected to the corresponding asset location. Zone detection is usually room-level, with accuracy of 1–10 meters.
I. Why is GPS not working in the indoors?
For the first time, many factories wanted to position their assets, and the first reaction was "gap GPS." But in the indoor environment, metal shelves, dense concrete walls, equipment casings are metal, GPS satellite signals can't even get through. The advantage of RFID is short-range communication stability, not relying on satellites, single label costs can be pushed to a few cents, just for warehouses, workshops, rooms, hospitals, closed scenes.
II. How to identify the area: From a "door-ban" approach
The most common method of area identification is "read and write at key entrances." For example, the hospital has a hospital that divides the inpatient section into a medical unit, a surgical unit, an ICU section, a single UHF antenna at the mouth of each section, with a mark trigger or infrared sensor. When a pusher or person passes through the door with an asset, the antenna reads a label, and the system automatically determines which area the asset goes into.
The advantage of this "door-ban" recognition is thatIt's simple logic, it's not easy to misjudge.The disadvantage is to know where the door is, which room the asset is in, which bed it is not. So it's usually used as a first-level position -- first frame large areas, then the second-level means of determining where it is.
III. How much precision can be achieved: See what technology you choose
Common scenarios are compared:
| Type of technology | Typical location precision | Applications |
|---|---|---|
| Unsourced UHF RFID+ Doorbar antenna | Regional level, no specific coordinates | Access to the storage depots, subdivision of the storage areas |
| Source 2.4GHz RFID+RSSI | 3-10 meters. | Level of building, intra-shop location |
| Active RFID+ Multi-Atron positioning algorithm | 1-3 meters | Positioning of shelf |
| UWB Superbroadband | 10-30 centimeters. | Positioning of personnel, tracking of high-value monostems |
If you only need to know which building or warehouse zone an asset is in, passive UHF tags and antennas at access points are sufficient. For rack-level accuracy, use active tags with a multi-antenna RSSI (signal strength) algorithm. Submeter positioning calls for UWB and is beyond conventional RFID.
IV. Pocketes that are stepped on the ground: metal, liquids, stacking
In real projects, positioning usually falls short not because of the technology, but becauseIn situ environmental disturbanceThe metal shelf reflects the signal, and liquids (such as chemical drums, fluid bags, blood products) absorb it, and assets are stacked together to cover each other. The same label is read well on the box, and may not be read directly on the metal cabinet.
There are several ways to deal with it: the metal surface is selected.Anti-metal layerWhen Shanghai-based Quest Technologies does project mapping, it usually sweeps the field using a grid, notes the reading rate for each area, then decides how to set the antenna, how much power is set, and this wheel is solid, and the system is much more stable behind.
V. KEY STEPS TO STAND
- Identify needs: first, whether to determine "regional identification" or "precision" and this step directly determines the technical selection and budget.
- On-site survey: Metal structure, space layout and asset type affect the reader layout, preferably by going through it.
- Pilot validation: Select a region to first install one, run two to four weeks to read and misperceive, and then spread the data.
- System interface: Positioning data must be connected to ERP, WMS or hospital asset systems for real business processes.
- Daily maintenance: a check mechanism for the breakage of labels, depletion of active tag batteries and the loose antenna must be in place and cannot be completed.
VI. BACK TO THE CORE ISSUES
The RFID asset location management is not complicated.Make an asset readable with an electronic label, and then you can translate "where to read" into "where to find the asset." Regional identification is covered by ZZQ1QZ at access and key nodes, and positioning accuracy depends on how much you want to pay for high precision -- one to 10 meters of RFID, and then down with UWB or Bluetooth A (Astebrow) solutions. Before choosing, you can get a clear view of the field environment, sort out the demand, and usually save half of the trouble.

Ms. Lei
Mr. Pang