Can the RFID Asset Positioning Management System locate people? Precision and application boundaries?
RFID Knowledge

Can the RFID Asset Positioning Management System locate people? Precision and application boundaries?

PublishedShanghai Zejie Smart Technology Co., Ltd.

First, the conclusion: RFID is based on a regulatory and locator is a side-office.

The RFID asset positioning management system is based on tracking and inventorying of such assets as trays, tools, equipment in the warehouse. Can it locate people?Yeah, but it's a scene.– The RFID tags are issued to employees, or the wristbands, and the system does sense that people enter a certain area, but they usually have a level of precision of 1-10 meters, mainly with door-to-door restrictions and nodes, not continuous tracking. Here's how it works, and precision and application of a layer of boundary.

How the RFID coordinates work

The RFID system consists of two parts: an electronic label on the object (or person wearing it), and a reader (also called a reader). Reader sends a radio frequency signal, when the label is activated, transmits the stored information back, reads the reader estimates rough distances based on the strength of the received signal (RSSI value), or locates through cross-referenced signals from multiple readers.

UHF RFID (860–960 MHz) is widely used for asset location. Tags are inexpensive, usually CNY 0.50 to a few yuan each, and read at several meters to over ten meters in open space, making them suited to large deployments. LF and HF tags read at shorter distances, from tens of centimeters to about a meter. They are used mainly for identification, such as access and meal cards, rather than location.

There are two specific approaches to positioning:

How do you do that?

The most direct thing to do is to get the RFID system to go through the "manager."Send a RFID tag to the employeeThe little chip in the card is read by a nearby reader, so you can record "Stand Three, 14:32 at Gate 3 of Workshop A."

This is a real practice in some industries, such as high-risk areas of chemical or power plants, recording the time and area of movement of personnel; parts of the hospital's sections, tracking the medical staff who use the equipment while tracking the valuable equipment; and forklift drivers in large warehouses, where pickers work.

In the projects we've been exposed to, chemical and manufacturing clients most often mention the need for "manipulation." They have deployed RFID doors at the end of their assets, and they have issued labels to employees, re-engineered existing networks and backstages without having to build an extra system, with low marginal costs.

Where is the precision boundary?

The precision of the RFID locator is not subject to a few practical constraints:

1. Signals are heavily disturbed.Metals, cement, and the human body itself absorb or reflect frequency signals. The same label, which reads 10 metres in an empty corridor, may be just 2-3 metres in a warehouse full of metal parts.

2. Stays in precision at the "regional level".RFID can't get the 10-30 centimeter precision of UWB, usually telling you "where is he at the workshop and which channel" and not where to locate the specific workspace.

3. Real-time ineffectiveness.The UHF RFID is used to avoid a collision of labels (a number of tags are also transmitted back and back), and there are only a limited number of labels that can be read in a stable manner.

4. Active vs. PassiveThe passive label without batteries, the reader responds by sending a signal, and people can read it; but when people remain still, they only know where the last time they appear. To track more frequently, you need to use the active tag with the battery, at a cost of tens of dollars.

The RFID location is about to be a little more precise.1–10 m, with 3–5 m zone-level positioning more commonAnd real-time is dominated by "incident triggers" and not continuous positioning.

And we'll look at it with other positioning techniques.

If you need to know exactly which table someone is next to, RFID can't. The following table is a comparison of several common technologies:

Technology Precision Typical scene Single Label Cost
RFID (UHF) 1-10 metres, regional level Access management, asset inventory 0.5 to $5.
UWB 10-30 centimeters. Power plant, tunnel personnel are precisely located A few hundred to a hundred.
BLE (Bluetooth Beacon) 2-5 meters. Indoor navigation, close alarm A few dollars.
Wi-Fi fingerprints 3-10 meters. General location of the office area Reuse existing Wi-Fi
GPS 3-10 metres (outdoor) Outdoor patrols, field missions Dozens of dollars for modules

The advantage of RFID is that it is cheap and can read hundreds of labels at the same time (one-time count of thousands of assets), which is not comparable to any other technology. But positioning precision and real-time accuracy are its shortboards.

What's the set for? What's not?

It's a good way to use RFID to locate people.It's often "Man and Assets Together" -- the purpose is to measure the length of time that a person enters or leaves a region, whether it should be there, rather than tracking the exact trajectory. For example, the high-risk field personnel arrives at an identification point, the count of the number of clean workshops and the logs of access, the area stopover statistics (for time for time and hours analysis) for warehouse operators.

Not a good scene.These are: security controls that require centimetre-level precision, real time movement of new locations per second, wide-range outsider tracking, and specific position or movement scenes (e.g., to determine whether a person falls). These scenarios either go up UWB, or take video analysis or wearable sensor routes, and RFID does not match.

How do you figure we should go to the RFID locator?

When a project is docked, we usually ask the client three questions first:

  1. What you need is "know where they are" or "know what they're in?" The former is enough for the RFID and the latter is going to go to UWB or BLE.
  2. Is the need for a locator raised with asset management? If so, RFID has the lowest cost of reusing existing infrastructure; if only by looking for someone, there is no need to go to RFID.
  3. Do you need to replay the historical trajectory? The RFID can only remember event points (when and by which door) without drawing a continuous track. UWB or video is more appropriate for a trajectory.

So, to answer these questions, the choice of options is basically in the right direction. When Shanghai-based Chettech does this, it usually starts by decorating the actual claims of clients into "assets tracking" and "person tracking", assessing feasibility and precision requirements, and then deciding whether to deploy RFID alone or to make a combination with UWB, BLE.

And finally, a summary of the boundary.

The ability of the RFID to locate people can be summarized in three words:

Before choosing the type, take apart the requirements of the "pipes" and "managers" and then make a lot less deviant than the site environment and budget.