What kind of rfid one-stop machine is, remotely read and write and hanger installed for resolution
RFID Knowledge

What kind of rfid one-stop machine is, remotely read and write and hanger installed for resolution

PublishedShanghai Zejie Smart Technology Co., Ltd.

What are the main forms of RFID integration?

The RFID One is a reading and writing device that integrates radio frequency modules, antennas and communication interfaces in the same shell, with common forms of desktop, industrial fixes, door-ban channel and suspension four. Select which main read distance, installation mode and application scenes, remote reading and writing and suspension are the most common combinations between warehouses and doors.

What about the one-on-one and "reader plus external antenna" split?

The advantage of a single machine is to deploy simple, less wiring, look clean, fit for fixed points, read a view that does not require complex scopes, such as a single cashier at the door, a single channel entry and exit. The partial approach is to separate the reader from the antenna, so it can be adapted to the field environment in terms of the position of the antenna, angle and number, suitable for complex environments, long-range or multiple coverage.

Cost-based One Machines are usually lower than part-size programmes, but the partial programme is more flexible. In actual projects, if there is a customity to the distance from reading, the coverage direction is required, and priority-specific packages are recommended; if the field environment is relatively simple, points are concentrated, one aircraft is more expensive than another. The two options are not a substitute relationship, and they are more complementary.

How much can a remote RFID read and write distance normally do?

The UHF-UHF segment (860-960MHz) is the most used frequency of remote RFID. In an open environment, with standard labels, a stable reading distance for a common one is usually 3-8 metres; high power-types can theoretically be more than 15 metres in size with a gain antenna and large size label, but environmental impacts are often significantly compromised in actual works.

The factors affecting reading distance are five in particular:

How do you put the suspension? What's the coverage?

The height of the top is usually 5-8 metres, and the door or line of production is typically 3-5 metres.

Coverage depends on antenna beamwidth. A rough estimate is coverage radius ≈ mounting height × tan(beamwidth ÷ 2). At a height of 5 m with a 90-degree beam, the radius is about 5 m and one reader covers a circle around 10 m across. For multiple readers, overlap adjacent areas by 20–30% to avoid blind spots.

If there is a requirement for directional identification (e.g., simply to read the library mouth and not to read the library mouth), the reading range can be kept within the width of the motion line by narrow-beam angles and adjust the antenna direction.

What pits are installed in the hangers?

What industries are suitable for a hanger RFID?

The clothing retail store is the most common application, where you do real-time count and cash collection protection on a test room or ceiling. The electrical stores and manufacturing stores link, which are mounted above forklifts or trays, identifies the swinger and tray labels. The archives and libraries also start to make them in a hanger, several times more efficient than handheld.

Shanghai-based technology uses a lot of hanger integrated machines in storage and retail projects, ranging from selection, dots and field commissioning. If the environment is complex, it is suggested that small pilot projects be prepared and batches spread, with the coverage on the drawings often different from actual sites.

What are the practical suggestions for selection and landing?

First, you clearly identify the demand and select the form. Read distance, install it, confirm three dimensions of the environment on the ground, and the trade-off between the four forms is clear. Second, the suspension project must be field-based. Metal distribution, height, motion width, power lines and grid lines are field-based, and it is normal for drawings and web lines to go off. Third, a single-point pilot is done before bulk spreads. A sample runs in a real environment for one week, coverage, serial reading, and drop-through rates are much more reliable than paper assessments.

Remote reading and writing and suspension are essentially two sides of the same thing: if you want to cover a wide range, you have to hang, you have to pull it steady, you can add synergy between the antenna and the field. So that's how you handle these two links, the RFID is actually running in the warehouse and the door shop.