What form of rfid handheld terminals is, and the manufacturer assesses and selects the dimensions
The RFID handheld terminals are broadly classified into five categories by appearance:Gun type (handheld trigger)、Cellular mode (consumption-grade appearance)、Rugged Industrial PDA、Flatboard TerminalandCan wear or modularize headersThe pattern determines how to hold, continue and adapt, and then think clearly of the scene before matching the manufacturer ' s capacity, which is more realistic than a brand-to-brand.
What are the main forms of RFID holding terminals?
The common RFID on the market has a wide variety of handheld terminal appearances, but essentially combines "read-writing modules + batteries + operating systems + antennas" in different ways. These are the five most widely exported forms at present.
Gun type (handheld)
The classic of the kind of thing, a trigger button on the handle, triggers a scan, and the whole machine looks like a thick scrutinizing gun. It's a good time to do a single-hand sweep of lots of labels, such as warehouse receipt, inventory, out of the library review. The handshake design reduces the wrist burden, and the trigger action is more powerful than the key.
Cellular mode (consumption-grade appearance)
The shape is similar to the normal smartphone, usually in 12-18 mm thick, and back-gary integrates into RFID antennas. It suits a little bit of "light" of the scene, like the door count, library loan, ticket approval, etc. The form is light, looks unshattering, employees or customers are very receptive. The price is that battery capacity and protection levels are generally less than industry.
Rugged Industrial PDA
The thickness is typically 25-35 mm, 300-500 g, four-angle rubber, and the outer case is thick. The protection level is usually IP65 or IP67, which can continue after falling to concrete ground at 1.5 meters. This pattern is logistics, manufacturing, mainstream selection of outdoor operations, carrying, durable, long duration.
Flatboard Terminal
The screen size is usually 8-10 inches, and the RFID reading-writing module integration is on the back or side. It suits a large screen, mass checking application, such as door shop full case acceptance, asset inventory car, shelf inspection. The tablets sacrifice portability, in exchange for wider viewing and more intuitive contrasting.
Can wear or modularize headers
The ring-scan, the wrist-reading, or a single head reading module to fit the normal mobile phone. This form is not fully developed in industry, but it's used in the case of scavenger lines, hospital materials management, short-lived operations like quick delivery, which can free up hands for other actions.
What's the difference between different forms?
The correspondence between the form and the scene is not absolute, but there is a general pattern:The more intensive the operation, the more demanding the environment, the more favourable it is to a heavy industrial form; the less intense the operation, the more environmentally friendly the lighter the patternAnd then, a few common scenes are going to compare.
| scene | Recommended form | Main considerations |
|---|---|---|
| Store daily scanned 5000+labels | Gun or industrial triad PDA | Hold comfort, keep sailing, resist falling. |
| The door shop count, 1000-3000 tags per day. | Cellular | Appearance acceptance, weight, cost of hand-held |
| Poor conditions such as cold storage, outdoors | Industrial Triple PDA | Protection level, cryogenic cell, working temperature |
| The door store full of receipts and checkes, lot checks. | tablet | Screen size, displaying clarity |
| Discretion line, hospital consumption management | Can wear or modularize headers | Free hands, co-ordinated. |
Shanghai usually asks questions about how many copies of the day are cleaned, what environment is swept and who is cleaning." The pattern is wrong. The next parameter is white.
What core dimensions should the manufacturer look at?
There are many RFID hand-held end-of-pipes in the market, but levels vary widely.
R & D inputs and own-owned lines
Can you do it yourself, or can you do it yourself, or is the design of the main plate not your own -- these determine the integer speed of the product and the speed of the problem. The manufacturers of the sticker or OEM usually have to do a look change, but they can't move at the bottom. A simple, rough way of judging: ask each other if "reading and writing modules are their own or integrated" -- and you can be sure that the producers who produce the chip platform and antenna structure are more credible.
Product Line Width
Only one or two of these products are more risky for the manufacturers, and it is not uncommon to sell out tomorrow.
SDK Openness and Documentation
The RFID handheld terminal eventually has to access your WMS, MES or SaaS platform, whether SDK is open, API is complete, documents are in Chinese or English, how fast the response is, and directly influences the project's landing period. The manufacturer can be asked to provide a SDK trial, and it can be counted after reading the document.
Industry cases and certification
See what industry is doing in manufacturing, retailing, logistics, medicine, and whether there are specific landings. And if the product passes basic certifications like CCC, CE, FCC, RoHS, at least it shows that it has done some homework on product compliance.
After-sale system
The handheld terminals are high-frequency tools, and the breakage, water inflow and battery decay are normal.
What are the specific hardware parameters to be followed in selecting a model?
The following are the technical indicators at the core of the RFID handheld terminal, each of which may directly affect the experience of use.
Frequency and protocol
The main domestic problem is the UHF, which usually works in a frequency range.840-845 MHz and 920-925 MHz, follow ISO/IEC 18000-63 and EPC Class 1 Gen 2. The HF (13.56 MHz) is used for door-barreling, ticketing, IC card etc. The two protocol systems are not common. The type of type must first be identified as to which labels you have.
Read distance and speed of reading
The typical uHF-held terminal reading distance is in3-10 metresBetween these, the impact is high on label sizes, antenna polarization, environmental disturbance. Read speed is usually measured by "How many labels per second" and mainstream products are typically in50-200 secondsIt should be noted that the distance of reading, as indicated by the manufacturer, is often measured in an empty laboratory environment and that the real warehouse environment is shrinking.
Antenna type
The radial polarization antenna is read at a distance but sensitive to direction, and the diametric antenna is more tolerant in its direction but slightly short. Most industrial handheld terminals use linear or interlocking polarization programs. The polarization is more stable when labels are placed on the side of the tray, stacked.
Protection level and resistance to fall
Industrial scenes at least.IP65If you want to see a new P67 (short-spill water).1.5 meters to concrete.Can you carry this? This is a relatively reliable data. It's normal to fall in the factory.
Batteries and re-carrying.
The battery capacity is usually in the same place.6000-10000mAh, continuous operation is typically around eight to twelve hours. Hot-swappable batteries are important: if a battery dies during an eight-hour shift and can't be replaced, work stops. Hot-swappable units let staff change batteries and keep going.
Operating systems and configurations
Android is currently the mainstream, taking over most of the new output equipment, from Android 9 to Android 14. The processor, memory (RAM 4-8GB), storage (ROM 64-128GB) determines system flow and availability in the coming years. It is recommended that mainstream configurations be selected so as not to become obsolete after a few years of buying.
Wireless connection
WiFi (twilder than frequency), Bluetooth (over 5.0), 4G/5G full-networking is the basic configuration. 5G or WiFi 6 significantly reduces data transmission delays when operating outdoors or large warehouses.
A few things that are easily ignored, but crucial.
Some of the detailed parameters are not visible, but the project is easily pedaled when it is online.
Can you see it in the sun?
The screen is barely visible when it works in an outdoor warehouse. Main industrial terminal is marked with a brightness of less than 500 nits.500-1,000 NITBetween, we'll take a closer look at the scene.
Key and touch screen gloves mode
The cold-storey operator wears thick gloves as a common requirement.Gloves Touch, whether wet hands are supported is a useful function rather than a point of sale in the parameter list.
Charge Method
Full charge, seat charge, Type-C direct charge, which is your field? Multi-machine shared seat charge is more economical than a plug-in, and batteries are charged faster alone, and the most convenient place to be found before deployment.
Label Compatibility
Under the same agreement, the labels of different manufacturers and chips vary greatly in their sensitivity. It is best to use your own current network labels for measurements, not just the compatible list given by the manufacturer.
Data security
Whether remote locking, remote erase of data can be done after the equipment is lost or whether it supports the switch-on password and disk encryption - which are hard requirements for industries involving sensitive information and cannot be ambiguous.
How can the programme materials from the manufacturer not be read in the loop?
How can you quickly judge the amount of gold by the fact that the manufacturer has provided several dozen pages of information on the programme?
- See if there's any.Specific model specification table, instead of just a graph of effects;
- See if there's any.Real scene test dataFor example, "reading 98% in 5 meters, metal shelf environment" is more credible than simply writing "reading 15 meters";
- Look.SKK Document Template, is usually more specialized in a well-structured and well-exampled structure than only "Corporate business requests";
- Look.List of interfaces, which interconnectors to the mainstream WMS, MES and ERP systems are supported as additional components for assessing maturity.
There's no standard answer to this selection, but there's a main line:First, we confirm the scene, then we determine the shape, and then we screen the manufacturer, and finally we look at the parameters.Each of these steps is done once, and the equipment that you have will be able to use. Shanghai has also found in its many years of project practice that while budgets are important, matching products with scenes is the key to determining success or failure.
It is suggested that you take this line of thought and talk to the candidates, so whoever can answer the questions above clearly and in place will be more worthy of moving forward.

Ms. Lei
Mr. Pang