rfid technology panoramic resolution: from radio frequency principle to full-band label and reading/writing device selection
One word.RFID (radio frequency recognition) reads and writes data from electronic labels in the form of a non-contacted electromagnetic wave, consisting of labels, readers and antennas. Readers send radio frequency signals to power tags and trigger their return data. The labels are divided by working frequency bands into low frequency, high frequency, ultrahigh frequency, microwave four broad categories, with a range of identification ranges ranging from a few centimetres to ten metres, and the applicable scene varies considerably; the key to the selection is that you first think clearly about what to solve, and then select the frequency band and equipment.
What exactly is the radio frequency principle of RFID?
Readers send radio-frequency-mounted signals of a specific frequency out of the antenna. The electronic label enters the RF field in two ways: passive tag (unactive tag) works on energy-driven chips collected by electromagnetic sensors or electromagnetic waves; active tag-inline batteries can launch a signal response.
Passive tag back-to-back data is based on "reverse disspersion" -- to adjust the data to reflect the range or phase, and then decipher the reader. The process typically takes time at milliseconds, which theoretically can be read a few metres away, and it's the essence of the difference with NFC: NFC uses a reading/writing distance of 10 centimeters to secure payment, and RFID seeks a more remote mass reading.
How does the RFID label and the reader say "to talk"?
Communication is subject to protocol. Common are ISO 14443 (13.56 MHz, used on bus cards, door-bar), ISO 15693 (same frequency band but more remote for recognition, in library, asset management) and EPC Class 1 Gen2 or ISO 18000-63 (860-960 MHz, which is the backbone of logistics and retailing). The animal identification is used by ISO 11784/85 (134.2 kHz).
The protocol addresses three things: how the label is "awakened," how multiple tags are queued when they return the signal (crash-proof algorithm), how data is coded. UHF Gen2 uses a dynamic time slot called "Q algorithm" that can be read more efficiently in a dense scenario, which is the central reason why many retail items choose it to be a cash count.
What are the types of labels?
There are three types by power source: passive tags are the least expensive and draw power from the reader; semi-active tags use a battery only to power the chip and rely on RF for communication; active tags use the battery to power transmission as well and can be identified at over 100 m.
The following are common in the form of sealing: metal resistant labels (which can also work on metal surfaces), soft tags (printable, water-washing) and hard case labels (trays, containers), single-time paper labels (teleport packages, dress chandeliers). The sealing directly determines whether it can carry high heat outside the household, oil stains, metal reflectors, and a failure to match the whole solution could collapse.
Read only, write multiple read-outs (WORM) and read-and-written by storage capacity.
How do you divide the full-band RFID labels? What's the appropriate scene?
Four bands correspond to completely different applications:
- Low frequency (LF, 125-134kHz)(b) Identification distance is generally less than 10 cm, with little water or metal exposure, and is often used for animal earmarks, car theft and a cartoon.
- HF (HF, 13.56 MHz)A typical distance of 10 cm to 1 m, with mature protocols, usually in the form of door-barriers, public transport, books, electronic tickets, NFC payments.
- UHF (UHF, 860-960 MHz): Identification distance 6-10 meters, and lot reading is very friendly, which is the main force of warehousing, retailing, logistics, asset inventory. But metals and water are its two most veritable enemies and require targeted label design.
- Microwave (2.45 GHz/5.8 GHz)(b) Bandwidth, distance and high cost, mainly for parking fees on roads and partial container tracking.
The UHF frequency bands are not uniform globally: China is 920-925 MHz, Europe and the United States 902-928 MHz, Japan 952-954 MHz. Export equipment must confirm compliance with target markets, otherwise labels may not be read at all under domestic compliance power.
How do you choose a reading and writing device?
Think about four questions: What frequency labels do you want to read? How far do you read? How fast do you read? How bad is the environment? These four answers basically frame out the range.
Readers are divided into four categories by form: fixed (door frames for door reading, such as the security doors of clothing stores), handheld (discount, battery power), industrial integration (integrator to production line or AGV vehicle), desktop haircards (in writing data). Fixed and sub-units - one antenna and host integration, fit for a simple scene; segment machines that are outside the antenna, can switch with multiple antennas and can cover complex areas.
An antenna selection is also critical. A Circumpolar antenna is insensitive to labels, flexible but short-range; it is far away, but requires that the tags are basically right. Multi-Air systems need to consider power distribution and beam overlap, and in practice it often takes on field-based adaptation to stabilize projects.
Key parameters to be addressed in the selection of models
- Read distance.: The nominal values are usually measured under ideal conditions, and the actual project may be reduced by 30% - 50% due to environmental impacts.
- Multilabel literacy: How many copies can be read in a stable manner. The storage scene usually requires more than 200 per second to be of practical value.
- Protocol support: Whether Gen2 and older ISO 18000-6B agreements are supported at the same time, affecting system compatibility.
- Interface TypeEthernet, serials, Wi-Fi, 4G, determine how to access the upper-level system.
- Protection level: At least IP65 in the outdoor or industrial environment, working temperatures usually require -25°C to +65°C.
What pits are easily stepped upon in actual deployment?
We have repeatedly encountered problems in doing projects:
- The reflection signal of the metal shelf leads to a blind zone, which must be assessed at the selection stage and, if necessary, resistant to metallic labels rather than general ones.
- Liquids, such as bottled water or fresh foods, sharply attenuate UHF signals. Change frequency bands or reposition the tags.
- And when you're in the field, too many labels are not read at all and if you don't get the impact algorithm right, you'll be "missing."
- Interrupts between readers, and multi-machine deployments are planned for channel and synchronisation mechanisms.
- The seemingly insensitive labels are installed — mistified, wrongly oriented and blocked to allow half the reading distance.
Shanghai's RFID in many industries is used to doing on-site radio frequency environmental assessments, and then deciding on antenna layout and label specifications, which are much more stable than direct mover programmes. In a radio frequency environment, paper assessment often gives only a broad direction, so field tests can level the pit.
Where are the RFIDs going in the next few years?
There are several directions that deserve attention: higher sensitivity on the side of the chip, lower effort, and continued down the cost of a single label; the trend in reading-writing side software to define radio frequency links that allow remote referencing and upgrading protocols; and the application side, increasing acceptance of ultra-high frequency (UHF) RFID by the retail industry, asset management, and the integration of RFID and sensors in smart manufacturing. But there will be no short-term scenario where all the scenes will be eaten in a frequency.Frequency SelectionIt remains a key starting point for success and failure of the project, rather than a secondary consideration.
If you start assessing RFID, the most safe way to do this is to get experienced suppliers with specific scenarios (number of labels, distance requirements, environmental characteristics). Read the principles, select the frequency band, and then test it by scene -- one thing is impossible, and then decide whether to spread it on a large scale.

Ms. Lei
Mr. Pang