What does rfid mean: the rationale and composition of non-contact automatic identification technology
RFID Knowledge

What does rfid mean: the rationale and composition of non-contact automatic identification technology

PublishedShanghai Zejie Smart Technology Co., Ltd.

RFID is the abbreviation of Radio Frequency Identification, which is one of the non-contact automatic identification techniques. It creates wireless communication between readers and electronic labels through radio frequency signals, automatically captures identifying information stored in labels, without manual intervention, and does not require optical visualization between tags and readers. In warehouse inventory counts, production line tracking, vehicle management, retail security, such as bulk, long range, automatic data acquisition scenes, RFID is already a very mature infrastructure.

Point 1: The RFID works in three steps.

The RFID system is not complex, it can be understood as a three-pronged "question-response-recording" process.

  1. Reader firing radio frequency signal:Readers (also called readers, Reader) form a radio frequency sensor area around them by means of electromagnetic waves that are exposed to specific frequencies in the antenna.
  2. Electronic labels receive energy and return data:When the passive label (the type with no built-in batteries) enters this area, its inner antenna is able to detect and transform into a radial energy, and when the label chip is awakened, it re-reflectes the internal ID or business data stored on the radio frequency signal.
  3. Reader decoded and uploaded:Readers receive the signal returned by the label and release the data to the upper machine system (e.g. WMS, MES, ERP) through interfaces such as a serial, net or bluetooth.

The whole identification process is usually done in 100 milliseconds, and that's the underlying reason that RFID is much faster than a barcode "cleaning" -- it can identify multiple labels at the same time without having to be matched one by one.

Element 2: The RFID system consists of three main components

No matter how it changes, the RFID system is bound to have three core hardware.

1. Electronic labels (Tag / Transponder)

The "id" is attached to or embedded in the identified object.

2. Reader/Writer (Reader/Interrogator)

The "host" is responsible for the launch of radio frequency signals and the receipt of label echo data.

3. Antenna

The number of antennas, the extreme way in which they are used, increases directly determine the distance and coverage of reading and writing. Fixed-readers usually have 2-4 sub- antennas, with handhelds having antennas.

We need a set of things besides hardware.Application softwareData docking, for example, by deconstructing the collected label ID into SKU, equipment number or personnel number in the operating system.

Element 3: Four work bands determine different uses

RFID is not a single standard, with four broad categories by work frequency and very different performance and application scenarios.

Frequency bands Typical frequency Read Distance Typical scene
Low frequency LF 125 kHz / 134 kHz less than 10 cm Animal earmarks, a cartoon.
HF HF 13.56 MHz Less than 1 m Library, door-barrel, bus card
UHF UHF 860~960 MHz 1~10 m Storage, logistics, retailing
Microwave Microwave 2.45 GHz / 5.8 GHz 10 m or more Vehicle identification, container tracking

The most used segment in industry and logistics is the UHF segment, which balances the distance from which it reads, the volume recognition capacity and the cost. In Shanghai’s High-Shanghai storage class, over 90% of labels and readers run on the UHF frequency, following the EPC Class 1 Gen 2 (i.e. ISO 18000-63) international standards.

Point 4: What is the advantage of RFID compared to barcodes?

The bar code is Optical Recognition, and the RFID is Radio Frequency Identification. The biggest difference between these two are three:

The disadvantage is also clear: label costs are higher than bar codes (UHF tags usually 0.5 to $3 a dollar), metals and liquids interfere with radio frequency signals, requiring impact-proof algorithms and protocol. So RFID is not replacing bar code, but rather replacing it in "Automated, Batch, Distance, Rewriteable" scenarios where the four dimensions are high.

Element 5: Focus on these five parameters in the selection of models

If you are assessing whether to go on RFID or to purchase equipment, it is suggested that the following five questions be answered:

  1. What are you identifying?The effects of metals, liquids, wood and plastics on radio frequency signals are completely different and require a matching of the special label.
  2. How much distance does it take to read?1-m, 1-10 m, UHF, more than 10 metres, basically only active.
  3. The speed of batch recognition?The high-speed transmission belt scene requires UHF and antenna layout, which allows for regular inventory selection of the general configuration.
  4. Do you want to encrypt the tag data?Select the tags and reader that support encryption algorithms when it comes to asset-proofing or sensitive information.
  5. How does the business system fit in?Confirms which interfaces are provided by the reader (RS232, TCP/IP, USB, Bluetooth, 4G) and whether SDK supports existing development languages and platforms.

Point 6: Typical landing scenes and common pits

From the project we were exposed to, the most easily RFID-landed pits are concentrated in three areas:

A run-through RFID system, three on hardware selection and seven on on site implementation and system integration. It is recommended that small POC tests be performed to confirm reading and writing rates (generally over 99%) before batching.

RFID is not a "just-in-a-load" tool, but rather a combination of business scenes, material, reading processes and back-end system integration. Understanding the work theory and system composition is only the first step, and it's on-site debugging and long-term transport that really determines how the project works. If you are assessing storage, production or retailing of scenes, suggest starting with label selection + ZZQZZ frequency + system alignment.