How can RFID fixed asset inventory be achieved? System configuration and efficiency resolution
The RFID fixed asset inventory is not complex to achieve: electronic tagging of assets, bulk reading of handheld terminals or fixed-readers that launch radio frequency signals, automatic return of label information to back-office systems and financial matching to generate a record of the gain and loss. Key is selecting hardware combinations, planning labelling options and pre-enabled data interfaces.
How did the RFID fixed asset count get up?
RFID is a technology that automatically allows the device to read numbers from air in an air-segregated environment. When inventory counting is used, the reader antenna sends out a radio frequency signal, the label on the asset is "awakened", and the asset it stored back to the reader, and the whole process does not require a manual sweep.
A complete inventory process is usually in four steps: first, the reader sweeps through a warehouse or office area, and dozens of hundreds of asset labels are read in bulk, timed in seconds; second, the numbering and time stamped package collected is uploaded to the middle, heavy enough to filter out abnormal readings; third, the system compares the physical numbers identified with the asset card in the ERP (Enterprise Resource Plan); fourth, the output discrepancy list - which are not in the books, which are not in the books, which are not in the books, and which are not in the books, which is obvious.
What hardware does a complete RFID inventory system require?
The base configuration is four blocks.
Label.The fixed asset count is usually labelled with UHF (UHF), working frequency bands at 860-960 MHz, long distances to support group reading. Normal paper does not dry glue labels on wood tables, plastic case is fine, but when you encounter a metal box, the cabinet is replaced by an anti-metal label, otherwise the signal will be shielded from metal and it won't read.
Reader.Breakup is a two-way end and fixed-pass. Handheld terminals are suitable for warehouses, a scattered scene like the office area, and operators can just walk along the route with the device. Fixed-space (also called door readers) is appropriate for access control, automatic recording of assets when entering or leaving the warehouse, often for IT equipment, medical devices, etc.
AntennaThe stationary reader usually requires an external antenna, the number and location of which are measured according to the field environment.
Backstage softwareThe intermediate is responsible for cleaning, archiving and reproducing raw data collected from hardware; the asset management system is responsible for matching and generating statements from the financial module.
When we deployed to a client who was working with sophisticated instruments, the final selection was UHF anti-metal tags + handheld terminals + desktop haircards, backstage docking using their original ERP asset module, reducing the count cycle from two weeks to half a day.
How do you choose the labels and how they are not easily misled?
The labeling programme is the most easily pedestaled link in the project.
Selection principles:Use on-metal tags for metal surfaces. Standard tags are fine for plastic, wood, or paper. On-metal tags usually cost two to four times as much, but save the labor of replacing unsuitable tags later.
Paste position:The laptop suggests that you put a bottom on the side of the table, that you can't easily touch it, and that you place your equipment in the front or top.
Code code:The code must correspond to the asset card number. It is recommended that a tag check sheet be created in the system, that the label be scanned and the asset number be bound to the database, so as to avoid confusion about "the label is on, not knowing which asset"
How much faster can a physical count be?
This is the number of people who care most. A workshop that counts 5,000 assets manually takes 5-7 working days for a skilled inventory clerk, with an average of 700-1000 per person per day and prone to leaks and miscalculations.
When you switch to a RFID hand-held terminal, the same 5,000 items of assets, two or three teams, can sweep the entire area for 2-3 hours, increasing efficiency by more than 10 times. The fixed-channel program is even more extreme, and assets are registered as if they had been pushed between them, with little manual intervention.
In terms of accuracy, manual inventory error rates are usually 3%-5% and the RFID programme can be contained within 0.5%, with the main errors coming from label damage or signal masking.
It is important to note that RFID is not 100% correct. Intensive piles of metal assets, multiple close-up devices in narrow spaces, will be missing. We arrange for a start-up and a redisk, which automatically compares with the initial data, and fixes the drop-out.
What pits are easily stepped upon during implementation?
Metal interferenceThe most common problem is that, as mentioned above, metal surfaces shield the signal of a frequency so that metal assets must be labelled with resistance to metals and there should be an appropriate gap between labels and metal surfaces (generally 2-3 mm) which cannot be directly stamped.
Reader density is not sufficient.The UHF label reading distance, although it can reach 3-8 metres, is reduced in the physical environment by the wall and metal shelf.
Network coverage.Handheld terminal data require real or quasi-real time retrieval, and wireless network unstable areas require pre-equipment programmes such as off-line collection and bulk uploading back to the office.
And connect to the existing system.The RFID collects the number in a technical language, which is translated into the business languages of finance and asset management. This requires intermediate support for standard interfaces (API, data exchange files, etc.) and strict matching with ERP's asset master data. Shanghai-based Chee Jiehue Tech Ltd., when it assists clients to land, does an interface-standard document, maps fields, code rules, and sets the main data source clearly at once, avoiding subsequent re-entry.
What's the late-life focus?
The maintenance workload is modest when the system is online, but three things are not going to go smoothly.
Label inspection:The label moves and wears with the asset, and it is recommended that a semi-annual check on the availability of the label be performed to detect failure and timely replacement.
Maintenance of equipment:Handheld batteries usually last two to three years. Reader antennas are low-power devices and do not normally need replacing for at least five years. Focus on charging practices and firmware updates.
Data governance:When assets are added, scrapped and transferred, the tag code must be updated simultaneously, otherwise the inventory results and the desk account cannot be reconciled. Many inventory errors are not RFID problems, and they are caused by changes in the asset code that have not been changed.
Summarizing: The RFID fixed asset inventory is achieved by a four-step "Taxi Program+Reader Selection+Intermediate Deployment+System Interposition" that increases efficiency more than 10 times the manual, with an error rate of less than 0.5%. It is often not hardware itself that determines whether or not the project succeeds or fails, but rather prior label planning, interface specifications and on-site surveys are in place. If you have a thousand or more assets, and there is a need for regular inventory, the RFID programme deserves careful evaluation.

Ms. Lei
Mr. Pang