Where is the fixed asset inventory using RFID? Efficiency and accuracy resolution.
RFID Knowledge

Where is the fixed asset inventory using RFID? Efficiency and accuracy resolution.

PublishedShanghai Zejie Smart Technology Co., Ltd.

The fixed asset inventory is using RFID. What's good?

RFID offers two main benefits for fixed asset counts. First, it takes a fraction of a second instead of more than 10 seconds to read an individual asset, and a few hours instead of days to count an entire store. Second, each tag has a unique code, eliminating manual transcription and significantly improving agreement between records and physical assets. In projects we have seen with several thousand assets or more, RFID saves about 70% of the person-days.

How fast is the RFID count faster than the manual?

The gap is mainly in the individual and mass actions.

Individual: A manual inventory of an asset consists roughly of finding the object, checking the labels, registering the status, recording the system in four steps, which takes 10 to 15 seconds on average; a RFID hand-held terminal sweep usually takes between 0.2 and 0.5 seconds, moving down by a scanning key, increasing efficiency between 20 and 50 times.

Bulk counting: A manual count of one office or part of a shelf often takes half an hour. Walking the aisle with an RFID handheld takes only a few minutes. A full warehouse count of thousands of pieces of IT or medical equipment can take four to seven working days by conventional methods, but RFID usually gets it done the same day.

Consider the labor in detail. A midsize company with 3,000 fixed assets previously needed three people for about a week. With RFID, it typically needs one person for one to one and a half days, plus time to check exceptions afterward.

Why would RFID reduce the error of the disk?

The error and the leak came almost from two stages: eye check and manual recording. RFID replaced both.

First, identify. The RFID electronic label (also known as the RFID radio frequency tag) sets a single global ID code, bound to the asset and then tied to the device, without any visual confusion. Barcodes or two-dimensional codes can easily be worn, faded, blinded, RFID labels read without contact, less exposed to surface pollution.

After the handheld terminal is swept to the label, the numbering goes directly into the account of the inventory system, and the automatic tag " in a state like " idle " , which reduces the errors and omissions caused by manual transcription. From the landed items, most of the RFID counts are accounted for more than 99%, while manual counts are generally between 92 and 96%.

Here, let me remind you that the accuracy rate is not attributable to RFID. The key is that the accompanying asset desk data and tagging be done before the inventory is taken, otherwise the labels and system records read out are not matched and the burden on the accounts increases.

How do you choose the fixed asset RFID label and how do you put it?

The label selection is based on the material of the asset and the use of the scene.

Common assets such as office furniture, paper-based case casings, non-metal, non-liquid surfaces are simply labelled with a normal paper-based, dry glue label, small size and low cost, and single sheets usually have a few cents.

Metal surfaces such as cabinets, medical device housings, and server chassis need on-metal tags. An internal RF absorber restores on-metal read range from a few centimeters to a usable 1–3 m. These tags cost several times as much as standard ones, but are practically essential on metal; ordinary tags are nearly unreadable there.

The position is also defined. Priority is given to areas that are flat on the surface of assets, which are not easily covered, such as side of the case, under-board beams, top of the file cabinet. The distance and angles read by hand-held terminals are measured in a physical count, avoiding the awkwardness of "stamping but cleaning" to read.

How does RFID count work?

A complete RFID inventory process is roughly four steps:

1. Asset sequestration: Create an archive of each asset in the system, write names, locations, responsible persons, then put RFID labels on it, take them to hold terminals and clean them once, and bind them to the system. This step is usually done simultaneously when the purchase is recorded.

2. Data downloads: The inventory is synchronized with the master and inventory systems on the day of the inventory, and the list of assets to be counted is forwarded to the terminal.

3. On-site scanning: The handheld terminal moves slowly in the asset area, and you hear a beep or see a signal light flashing. A passway point is fixed to the cart or door at the entrance, and the asset is automatically read and suitable for a large number of scenes.

4. Data return and processing anomalies: The scanned records are uploaded to the system when the terminal returns to its working position, and the system automatically compares with “due” and “real” to generate an abnormal list of losses, gains, and deviations, which is processed manually.

How do you get through the RFID system and the existing ERP?

Most fixed assets RFID projects do not replace the original ERP, but rather make a middle layer. The inventory system connects the fixed asset module that is connected to ERP through a database view or standard interface, maps the tag ID that RFID reads to the ERP asset number and returns the results of the inventory count.

The data exchange fields usually include: asset number, asset name, location of storage, responsible person, state of use, time to count. The structure is simple, the amount of data is not large, and the interfaces are normally accessible for days as long as the field on the ERP fixed asset table is clearly defined.

If enterprises use a mainstream national ERP such as friend or butterfly, the docking template is mature and the interface workload is mainly on field mapping and differential treatment rules.

What are the easy pits for RFID to take?

Several common questions deserve to be borne in mind:

Metal interferenceMetals and water are the two grammes of RFID. The metal surface must be used for basic reading with a regular label.

♪ To keep the mutually exclusiveWhen you are in a very high asset stack, the front row labels block the back. Handheld terminals need to be moved from one place to another and to the antenna angle, where necessary, with an antenna or a portal on the ground.

Label Cost ControlThe label appears to be small, and thousands of items add up to the total amount.

One success rate.: In theory, RFID supports bulk reading, but there are often various disruptions on the ground and the success rate of the first run is usually reduced by a small pilot.

Shanghai-based Sieve Technologies have accumulated experience in many fixed asset RFID inventory projects, ranging from label selection, end configuration and interface with ERP, which can be removed together when specific scenarios are encountered.

What kind of business fits on the RFID?

Simple judgement: The assets are more than 500 in size, spread over a number of floors or locations, and the RFID is basically a return book for businesses with consistent accounting requirements. The smaller size of the Excel+ barcode is enough; the asset is of high value, the count cycle is tight, the error-cost scenario is high, and the more the morning the RFID is going to work out.

If the current asset desk account base is weak, it is recommended that the rules for billing and coding be streamlined before introducing RFID labels and data capture links, which would be counterproductive.