nfc tag application scene count: from asset management to security backtracking
RFID Knowledge

nfc tag application scene count: from asset management to security backtracking

PublishedShanghai Zejie Smart Technology Co., Ltd.

NFC labels have been used extensively for years, from factory inventory to commodity security. But many people are vulnerable to choice: several of the chip models, multiple price differentials, or 213 or 216? Can you read them on the metal surface? Will they fail in months?

Cost dimension: Correlation of label type to unit price

The common civilian NFC chip models on the market are NTAG213, NTAG 215, NTAG 216. Using blank labels for bulk purchases, for example, NTAG 213 costs approximately $0.3 to $0.8, NTAG 215 about $0.5 to $1.2 and NTAG 216 about $1 to $2 (public quote for reference power platform, 2024). The variance is mainly from storage capacity - 213 are 144 bytes, 215 are 504 bytes and 216 are 888 bytes.

NTAG213 is enough for a URL or simple ID. For traceability records carrying production lots, dates, and transfer points, NTAG215 or NTAG216 is a better choice. The larger the order, the lower the unit price. Orders of more than 100,000 tags usually qualify for another pricing tier.

Effect dimension: read-and-written distance and environmental tolerance

The standard read-written distance of the NFC label is around 4 cm, but in practice the size of the label antenna, the sealed material and the reading-writing device are very important.

But if you stick it on a metal surface or in a liquid container, the reading distance drops sharply -- the metal shields the electromagnetic field. This is when you need to select an anti-metal label, with an iron oxygen-proof shielding disk that is 30 to 100% higher per unit than the normal label, but the reading range stabilizes at 3 to 5 centimetres. The liquid environment needs to be thickened or special coating labels, otherwise the signal will be absorbed.

Application of scene dismantling: from asset management to security against fraudulent traceability

The requirements for labelling vary widely from scene to scene, and are grouped below into two common uses.

Asset management scene

Such scenarios are usually sufficient for NTAG213, with a single cost contained within one dollar, focusing on the durability and paste reliability of labels - the labels recommended in industrial environments for PET or epoxy resin sealing.

Anti-perjury source scene

The tracer scene usually requires more data, and NTAG 215 or 216 is recommended. The security scenario also requires that the data should not be tampered with, often along with digital signatures or block chain certificates, and a single label will cost much more than an asset management scenario.

Common pits: selection and practical problems in implementation

Pipe 1: Consider NFC as a long-range identification technique

The standard NFC distance is usually not more than 10 cm, and it's a close-to-the-ground communication design. If you need to read it in a long-range batch, like the whole-of-a-truck-up-of-storey, you should use the UHF RFID, which can work at 3-10 m, which is a completely different technical route. Using NFC labels on sites that require remote reading, it is the pit most easily pedaled by new hands.

Pipe 2: Ignore the sealing and pasting of labels

The label used outdoor or long-term must be considered for waterproofing, scratching, and heat resistant. The generic dry glue label may fall off or fail in months of oily environments or outdoor tan. It is recommended that the labels used in the environment are more expensive but can be increased several times over.

Pipe 3: Cellular compatibility is not measured in advance.

Most mainstream machines support NFC reading and writing, but some of the equipment that is old or custom-made may be limited. If you trace it to consumers, you can recommend a round of compatibility tests with the mainstream model in the market before official deployment, so as to avoid "no clean" complaints after going online.

Pocket 4: Think NFC can be perjury-proof.

The NFC tags are theoretically read and even rewrited. Thus, the key anti-false scene cannot be based solely on the NFC itself, but also needs to be verified with encrypted signatures, block chain certificates or backend servers, and a single label is not perjury-proof.

The selection of NFC tags starts with three things: how much data is stored in the scene, what environment is used, who reads it. These three things are relevant to label type and sealing, which largely avoids most pits. Shanghai-based Chettech, when helping clients make this kind of choice, usually sorts out the demand in that order, then determines the label type and how it works.