Distinction resolution of nfc labels and rfid tags: frequency band differences and selection application recommendations
RFID Knowledge

Distinction resolution of nfc labels and rfid tags: frequency band differences and selection application recommendations

PublishedShanghai Zejie Smart Technology Co., Ltd.

Many people think that NFC and RFID are different, but they're not.

Many people first come to the two terms and think they are parallel technologies. But in principle, NFC is actually a branch of the RFID system - specifically working on the 13.56 MHz band, with a short distance of RFID that is deliberately limited to 10 centimetres. First, this relationship is rational, then the frequency range difference and selection is fine.

From the frequency, the core difference between NFC and RFID.

The RFID is the sum of a set of technologies, with frequency bands covered from low frequency to large microwave.

The NFC frequency band is fixed at 13.56 MHz, so it's the same as HF RFID in the physical layer. But the NFC further specifies on the protocol level that: A or B card simulations in ISO/IEC 14443 must be supported, three modes of reading and writing and equivalent communication work, with a transmission rate limited to 106 kbps, 212 kbps, 424kbps. These restrictions guarantee compatibility between different manufacturers and directly determine the NFC's "plug-in" experience.

Why does the NFC have to be close and RFID can read a few meters apart?

There are two different ways to combine. Low-frequency and high-frequency RFIDs depend on them.Electric connection.: The reader antenna generates an alternating magnetic field. This induces current in the tag antenna, powering the tag so it can send back data. The field weakens quickly with distance, naturally limiting range. NFC takes this further by limiting range to under 10 cm, typically 4 cm or less in actual products. The point is security, not an inability to read farther.

For tapping transit cards, making mobile payments, and unlocking access-controlled doors, the need to hold a device close is itself a key design feature for preventing accidental reads and relay attacks. If the range is extended, someone nearby could potentially read or interfere with the exchange. UHF RFID, by contrast, usesElectromagnetic Reverse Dispersion: The labels reflect the radio-frequency energy from the reader back and adjust the data, are highly oriented and spread far away and fit a mass count of hundreds of cargo.

Conflict prevention and group reading: pits easily pedaled when choosing

Another difference that directly affects selection is the ability to read multiple tags. UHF RFID supports dense-reader mode and anticollision algorithms and can identify dozens or even hundreds of tags at once. That is why it is widely used in apparel, parcel delivery, and stock counts. NFC and HF RFID have some anticollision capabilities, too. ISO 14443 Type A, for example, uses an anticollision sequence to identify a small number of cards. But the short read distance and limited magnetic field mean they only read one to three cards at a time in practice, making them unsuitable for bulk counting.

Another detail is data capacity and encryption. The NFC labels typically contain hundreds of bytes to KB, often for URLs, text or trigger actions; the UHF RFID has a larger user-data area that is often used in accordance with the EPC code (Electronic Production Code) and contains the only identification and extension information for more than 96 places. In terms of encryption, NFC progeny supports many encryption algorithms (e.g. AES, SHA, etc.) that are more suitable for situations involving payment or identification documents.

Actual selection: by scene rather than by technical parameters

Compare the parameters clearly, the selection is a "show-and-see" problem. In combination with Shanghai-based Triangular Technologies’ experience in several projects, there are several judgment logics that can be used:

  1. Interactive for consumers, needing to post a cell phone or card(e.g., products are not fraudulent, after-sale warranty, exhibition sign-ups, ads are on the way): select NFC tags, read and write with NFC cell phones, deployment costs are lowest.
  2. House arrest, bus service, membership card, electronic license.: With HF RFID (13.56 MHz, ISO 14443/15693), the reading and writing speeds are balanced with card form.
  3. Logistics, warehousing, production-line traceability, asset management: Choose UHF RFID. Focus on range, bulk read speed, and integration with your existing WMS and MES.
  4. Abundant environment, metal surfaces, liquid environment(e.g. livestock, mold management, car spare parts): The general high frequency and UHF tags are used as LF or a special anti-metallic URF label, which will significantly decline in these scenarios.

The label cost, the unit price of the reader, and the system's integration difficulty are also considered when selecting a type. The NFC label unit price is usually 0.5-3 dollars, the HFC tag is similar, the UHF tag price is slightly higher but it falls significantly; for readers, the mobile phone is the natural NFC reader, the HF needs a special card reader, and the HHF requires more power-intensive fixed or handheld devices.

A few pieces of the puzzle.

Finally, several common misunderstandings were clarified:

Back to the selection itself: First think of what to solve (prevent; pay? take an inventory? identify?), then look at the environment (distance, metal, liquid, human flow density), and finally match frequency bands and protocols. Technical parameters are tools, and scenes are the starting point.