How to control the management of spare parts inventory? Lower stock and secure supply
The stock is to be controlled by a combination of needs, replenishment cycles and the risk of non-materials: management effort is to be determined by classification, security stocks are to be used to cope with fluctuations, reorder points are to be used to trigger procurement, and parameters are to be revised on an ongoing basis through slow warning and periodic count.
We'll deal with the problem of "we got the goods but we can't find them" first.
A plant that did equipment maintenance, which was counted at the end of the month, found that there were a number of bearings on the shelf, seals and electrical modules, and maintenance staff were still requesting urgent purchases. The reason was not complicated: there were multiple codes for the same spare parts, the amount of the booking was not deducted from the unused material, some of the spare parts were placed in the inspection area, the system showed inventory but could not be used directly on site.
The starting point for the management of spare parts inventory is not to compress immediately, but to calculate “available stocks”. It is recommended that stocks be decomposed into four calibres:
- Booking inventory:Number of systems recorded.
- Available inventory:Booking inventory less frozen, pending inspection, allocated and ineligible quantities.
- In-transit inventory:Number of orders issued but not yet entered in the database.
- Security inventory:Number of buffers retained to respond to fluctuations in demand or delivery.
The parts code also requires uniform names, specifications, application of equipment, units of measure and alternative relationships. For units such as "Packages, Sets, Boxes", conversion rules must be established. Shanghai-based Select Technologies Ltd., when combing the inventory process, takes a lead, refunds, borrows, scraps and transfers separately, avoiding all changes being processed in a "inbound and outbound operations single" blurry.
Levels by level of importance to avoid the use of the same set of rules for all spare parts
Warehouse personnel often encounter two extremes: the long-term occupation of funds for high-value spare parts, and the lack of goods for low-value but critical seals during maintenance. The solution is to separate “value importance” from “cut off impact”.
Number of times to count by value classification
The following is the threshold for easy-to-land examples, which are management illustrative data and do not represent actual statistical results of a given enterprise:
| Category | Percentage of annual consumption | Manage Actions |
|---|---|---|
| Category A | About 70-80% of the total. | Monthly review of parameters, monthly or quarterly count |
| Category B | About 15-25% of the total | Quarterly review, six-monthly inventory |
| Category C | About 5-10% of the total | Biannual or annual review, as required |
This group is a common management start-up area, and the actual classification should be based on the enterprise's record of receipt for almost 12 months.
Modify classification results with stopover effects
A $20-per-unit seal, if the missing goods will shut down the entire equipment for two days, may have a higher management priority than the $2,000 per unit, but can wait for the normal parts to be purchased. It is proposed to add the key spare parts logo and record at least three elements: the impact of the stoppage after the lack of goods, acceptable waiting times, and whether there are alternative models.
In practice, spare parts can be divided into four groups: “critical and common, critical but less used, ordinary and low-used.” Key and commonly used spare parts are set up at a higher level of service and clear replenishment points; key but less used spare parts focus on the supply cycle, alternative sources and shared stocks; common and less used spare parts need to be avoided.
Count the stock, not the empirical.
A warehouse has been used to “buy half as much” in the past, but the procurement cycle varies from 7 to 35 days, resulting in a backlog of spare parts and a downtime for some.
Start procurement with reordering point
The additional point of order is the threshold for initiating procurement when inventory is reduced to a certain quantity, which is commonly used as:
Reordering point = average demand over delivery cycle + secure inventory
Example: For a spare part, an average of 40 items per month has been consumed for almost 12 months and an average of approximately 1.33 items per day at 30 days; the vendor ' s normal delivery cycle is 20 days and the safe stock is set at 15 days, if:
Reorder point = 1.33 × 20 + 15 ≈ 42 units
When available inventory plus a determined arrival of about 42 items, the procurement or redeployment should be triggered. 40, 20 days and 15 items are demonstration data, with actual parameters to be derived from the historical records of the enterprise and the record of the acquisition arrival.
Keep your safe stock unsettled.
Secure inventory can be adjusted to the degree of volatility. Demand is stable, delivery of reliable general spare parts can be delivered, buffers can be smaller; demand is concentrated on a period of overhaul, supply cycles are often extended or shortages cause downtime spare parts, and buffers need to be increased. Monthly measurements of actual requirements versus days of arrival compare the difference between projected and actual values.
If actual use of a spare part stays below 70% of the forecast for three months in a row, the demand parameter can be lowered. If it exceeds 130% for two consecutive months, check for newly commissioned equipment, changes to maintenance plans, or failures of substitute parts. These percentages are examples for internal management and do not replace analysis of the company's own historical data.
Control the amount of a single purchase with minimum and maximum stock
The problem of overpurchase may arise once, with only reordering points. For spare parts that are relatively stable, a minimum and maximum stock can be set up:
- Minimum inventory:Usually, the reordering point is followed by a focus on preventing disruption of supply.
- Maximum inventory:To meet the need for a replenishment or plan cycle, while limiting the use of funds.
- Proposed procurement volume:Maximum stock - available stock - in transit stock.
For example, the maximum stock of a common spare part is 80 items, 46 items are available and 10 items are in transit. The recommended procurement volume is 24 items. If there is a minimum packing volume of 10 items, the number is adjusted to 20 or 30 items according to the packing rules and the reasons for the adjustment are recorded.
For special, large and high-value spare parts, it is not appropriate to simply apply the maximum stock. You can use "order-activated" instead: purchase after confirmation of maintenance plan or share a reserve with multiple equipment. This will preserve supply buffers and reduce the stagnation caused by equipment upgrades.
Counts are not limited to a few, but also verify whether the inventory is working.
Some of the inventory matches, but is stored beyond the shelf life; some electrical packages are broken and not marked for inspection when they are in storage; others have been replaced by new numbers, but are still considered to be normal stocks by the system. The count should be checked both in quantity, location, state, batch and application.
A cycle count is recommended, without waiting until the end of the year for a single count. The monthly count of categories A and B and the six-monthly or annual count of category C are recommended. The differences in inventory are distinguished by: missing clips, misplaced storage, unit conversion errors, unused end-of-life, actual wear and tear. Different reasons for different modifications cannot be adjusted to volume alone.
The warehouse should also maintain a list of slow-moving spares. Review spares not issued for 12 consecutive months. For items not issued for 24 consecutive months with no clear equipment need, assess redeployment, substitution, return, or disposal. Twelve and 24 months are common review periods; adjust them for maintenance cycles and spare-part life.
Set indicators between “less stock” and “continuing supply”
It is recommended that the reduction in inventory should not be based solely on stock levels.
| Indicators | Calculate method | Actions after the discovery of a problem |
|---|---|---|
| Inventory accuracy rate | Number of total count counts x 100 per cent | Tracing codes, warehouse locations and access logs |
| Shortage rate | Number of applications for missing materials = total number of applications for the receipt of materials x 100 per cent | Review of requirements, delivery cycles and secure inventory |
| Proportion of inactive stocks | Value of slow-moving stock ÷ total inventory value × 100% | Check for duplicate purchases, equipment changes and replacements |
| Percentage of emergency procurement | Emergency procurement amount = total procurement value x 100 per cent | Reordering points and schedule forwards |
Managers can export a page of an anomaly list on a monthly basis, but only keep items that need to be addressed: inventories are below reordering points, over-the-counters, unaccompanied, unsubscribed, critical spare parts are not replaced, procurement cycles are abnormally extended. Parameters do not need to be set up at a time, and first, using data for almost 12 months, to build the first edition, which is revised monthly based on actual results, usually more easily than in-experienced stocking.
The core of spare parts inventory management is to allow each stock to answer three questions: why, how much and when. Using the available stocks as a basis for tiered, important reordering points, secure stocks and static warning controls, it is possible to retain the necessary supply buffers while reducing the amount of funds spent. For high-equipment, complex spare parts coding scenarios, it is recommended that the test start with critical equipment and high frequency spare parts, and then gradually expand after the calibration of data has been confirmed.

Ms. Lei
Mr. Pang