What's nfc tag? Structure composition and rationale.
RFID Knowledge

What's nfc tag? Structure composition and rationale.

PublishedShanghai Zejie Smart Technology Co., Ltd.

What is an NFC tag, and how does it differ from the QR codes and Bluetooth we use every day?

The NFC label is a passive electronic tag using Near Field Communications, which does not itself have batteries, powers and transmits data by the electromagnetic field that comes in close to a reading/writing device (e.g. a mobile phone). It typically works within 4 cm, with a common specification of 13.56 MHz frequency bands.

The NFC tag does not need a camera to match it, is free of light and can be repeated; and Bluetoothby, which doesn't have to pair, does not consume cell phone power, usually within 100 milliseconds. One sentence: the NFC label fits a short-range scenario for "read on touch," like a doorbar, payment, product trace.

Which parts of the NFC label are?

A complete NFC label usually contains four layers from the outside:

The chips and antennas are connected by the arctic conductor (ACF) of each direction. The gel is both electrically and mechanically, which is a key to label life. We have seen early products in the storage client's project because of the inappropriate type of conductive conductor, and three years later there was a mass failure to read.

How does the NFC label work?

The process can be broken down into three steps:

  1. Incentives: Cell phone or reader firing the intersectional magnetic field of 13.56 MHz, where the label antenna senses a sensor current after reaching the magnetic field.
  2. Electricity and response: Sensible currents are managed to power the chip, which superimposes internally stored data through load mode (Load Modulation) into a magnetic field.
  3. DecodingReader detects magnetic field changes, deciphers data and completes one reading and writing.

The whole process label does not launch radio waves, it's just a "reflective" reader signal, so the power is extremely low and the possibility of being wired. This is also the physical basis for NFC to use in lock-down and payment with high safety performance.

What are the types of NFC labels? What's their respective scene?

The five label types defined by the NFC Forum are most commonly cited in industry, and they vary in terms of protocols, storage and speed:

Type Compatibility criteria Typical capacity Common uses
Type 1 ISO/IEC 14443A 96 bytes – 2 KB Simple URL, URL Jump
Type 2 ISO/IEC 14443A 48 bytes – 2 KB Smart posters, protection from hypocrisy
Type 3 ISO/IEC 14443A / JIS X 6319-4 1 KB – 9 KB Transport card (Japan Felica System)
Type 4 ISO/IEC 14443A/B Up to 32 KB Payments, complex applications
Type 5 ISO/IEC 15693 Maximum 32 KB or more Logistics, asset management

If you only need to store a URL or ID, Type 2 offers the best value. For payments or applications with higher security requirements, use Type 4 with a cryptographic chip. For warehouse stocktaking where you want to scan an entire stack at once, Type 5, the longer-range variant, is a better fit.

How many data can NFC tags save? How many times do you read and write?

Storage capacity varies from 48 bytes to dozens of KBs. A NDEF text records about 50-200 bytes, a URL records several dozen bytes, so even this small capacity label, Type 1, can save dozens of short links.

In terms of reading and writing life, the number of wipings of mainstream chips usually ranges from 100,000 to 1 million times, with data preservation starting 10 years (some industrial products can be labelled 30-50 years). Read is not limited in number, but has a ceiling. Physical bends and high temperature environments significantly reduce lifetimes, and posting on metal surfaces is also a failure because magnetic fields are shielded, which requires an additional layer of anti-metal layers.

Where does the NFC label actually work?

The following are some of the more frequent scenarios that have been found:

We did a equipment inspection programme for a precision instrument factory, with a Type 5 label inside the cabinet and an anti-metal bubble cotton, which is not afraid of metal shielding or stable to read while wearing gloves.

Which pits should be taken into account when selecting or using NFC labels?

The following are common questions drawn from the project:

  1. The chip model is not clearly marked.: Also Type 2, NTAG 213, NTAG 215, NTAG 216 different in capacity and password mechanism to confirm model before writing script.
  2. The size of the antenna does not match the reading and writing distanceThe 25 mm-diameter label reads about 1-2 cm, 50 mm to 4-6 cm. The smaller the size, the more you consider the impact of the cell phone shell and the thickness.
  3. Metal surfaces are unresistant.: Directly attached to metal cabinets will not be read at all and will require specialized anti-metal labels or bubbled cotton mats.
  4. The outdoors are on the wrong side of the sun.: Normal PVC rembrands with long-term UV exposures are yellow and flaccid, and PET or UV coating is recommended.
  5. Use NFC labels as the only way to protect against forgery.: The label itself can be copied, and the security should combine with the only UID, encrypted signature and backend verification of the chip, not just " one touch to verify the truth".

How do you judge the quality of a NFC label?

Three parameters can be highlighted:

If you apply higher reliability requirements, such as door-barrel, payment, bulk asset management, it is recommended that the original chip factory trace file be obtained from the supplier prior to procurement and that small batch samples be tested for high temperature, high humidity (85°C/ 85% RH, 168 hours).

The final value of the NFC label is not worth it.

The advantage of NFC labels isLow power, short distance, immediate contact., is it very appropriate to need a "touch-and-take" information scenario. If you're assessing two-dimensional code, bluetooth and NFC options, you can judge from these three dimensions: Do the interactivity distance need be less than 5 centimetres? Do you want to be able to repeat your writing? Do you want to finish reading without being connected? If the answer is yes, the NFC label is the more appropriate option.

In the selection and landing process, chips type, antenna size, patches, application layer protocols (NDEF) often determine the success of the project. If you are facing a specific scene selection problem, you can list your capacity, distance, environmental hardness requirements, and then select the appropriate label type and program path.