What are the functions of the spare parts management software? Discrepancies with generic inventory software
Last winter, a food packaging plant called at two in the morning. A servo motor on the filling line had burned out. Searching the shop floor in the dark, staff took 40 minutes to dig out a spare from a cardboard box in the corner. The model appeared to match, but after mounting it they found that the encoder interface was the wrong version, costing another half hour. After that, they decided to implement a dedicated spare parts management system.
The management of spare parts appears to be a subset of inventory, but running shows that the problems it is about to solve are almost non-overlapping with generic inventory software.
What is the problem with the generic inventory software?
The generic inventory software (also known as the "surveillance or warehousing management system") is designed around "commodity flow," with three numbers: current, in-stock, out of stock. It treats each SKU as a substitute for a good -- as long as it's correct.
This logic is appropriate for situations such as trade flows, finished stores, and electricians.
The spare parts on the industrial site are not that logic. One bearing may be of a five-six-size device, one sensor with two-generation versions and three-man alternatives. Only in quantity is there no answer to the question "what should this equipment be replaced by?"
What's the spare parts management software to do?
The focus of the spare parts management software is "is the equipment going to work on a sustainable basis" and it is rather minor. A serviceable spare parts system usually covers these functions below.
Material Encoding and Multi-Drive Properties
The parts must have their own code rules, not just names. The same-specified seal, different manufacturers, different materials, different applicable pressures, and the coding must be separated. The properties typically include model, specification, material, application equipment, critical levels, suppliers, material replacement relationships. Here, "critical level" refers to whether this part is broken that leads to a complete shutdown or only affects auxiliary functions, deciding directly how much is available.
Device Tree Associated with BOM
Each spare part is to be mounted on a specific device or sub-component of the equipment. BOM (material list) is a tree structure that records what a device consists of, and each component can be carried out into, specific parts. Clicking on an emulsor's equipment card to drill down to the "prime pressure system oil pump seal" to directly locate which spare parts should be used, save the work of flipping the form.
Safe stock and multi-level warning
Low-stock alerts for generic stocks are only one number - current stock is below the given value. The early warning logic of spare parts management is more complex: considering equipment critical (higher redundancy of key equipment spare parts), procurement cycle (three months for imported items to arrive), historical consumption rate (six times for a model bearing, and six times earlier next).
Maintenance worksheets associated
The spare parts are not "sale out" but "maintenance out of the house." Each consumption has a corresponding worksheet, equipment, maintenance staff, cause of failure. This has two advantages: one is to calculate the cost of repair per device and the other is to predict when replacement will be needed in the next time based on the breakdown data.
Batch and Serial Number Back
Key parts go back to batches and even individual serial numbers. For example, if a cylinder is in trouble, find out which shipment it was, which supplier it was installed, when it was loaded, how long it was running on that device. Once the batch was found, it can be located immediately in all service. Medical devices, food, semiconductors are more demanding for traceability.
Early warning and procurement recommendations
A mature spare parts system will automatically generate procurement recommendations based on current inventory, consumption rate, procurement cycle, equipment shutdown risk. Key spare parts may be recommended for replenishment six months in advance and ordinary spare parts will follow the normal cycle.
The most critical difference between the two
Putting the above in a sentence: General stores run "How much is it?" and spare parts manage "is it sustainable to use the equipment."
| Dimensions | General-purpose inventory software | Spare parts management software |
| Core objectives | Accurate number of commodities and accounts | Availability of equipment and downtime risk |
| Encoding Method | SKU code, classified by class | Spare parts code + equipment/parts association |
| Out of the library logic | Sales, transfers, access | Maintenance worksheets, preventive replacements, emergency calls |
| Basis for early warning | Minimum inventory value | Key level + consumption rate + procurement cycle |
| Retroactivity requirements | Retroactivity of batches (food/medical requirements) | Batch + Serial Number + Device Tie |
| Data Association | Communication with sales, procurement modules | Communication with equipment desk accounts, maintenance worksheets, spot checks |
The table contrasts clearly: generic stocks are "commodity perspective" and spare parts management is "equipment perspective." Both data models are designed almost from scratch, force the general inventory to handle spare parts, and then become an Excel form.
What pits would be used for spare parts in general-purpose storage?
Many enterprises start off with a few problems when they want to save money and use existing ERP or inventory modules to manage spare parts.
First, the coding system is not matched. The ERPs are coded by type of material and spare parts are carried out according to "Equipment-part-part-part" which conflict with each other.
Second, the warning logic is too thick. The low-stock alert for ERP only recognizes one number, and spare parts need to be graded by key -- the same screw, ten on critical equipment, two on assistive equipment.
Third, maintenance costs are unclear. The decoupling of the out-of-house and worksheets resulted in an unusually high cost of maintaining a particular equipment at the end of the month, but it is not known where it was used.
One precision component machining customer initially managed spare parts in its ERP system. The books showed enough stock, but staff still had to search through boxes to find anything. After adopting a dedicated system, average waiting time during downtime fell from half an hour to less than ten minutes. Less capital was tied up in spare parts too: the business now had the data to reduce the extra stock it had kept for peace of mind.
How do you decide if you should be on a special system?
Several simple criteria for judgement can be consulted.
The equipment, which exceeds 50 units or spare parts SKU over 500 units, is no longer available on Excel and general-purpose stocks and it is recommended that a specialized system be evaluated.
The equipment is distributed over a number of factories or workshops, requiring redeployment across the plant and much savings from the multi-warehouses of specialized systems and the transfer logic.
The spare parts contained imported items, long procurement cycles or a strict batch retroactive requirement (medical equipment, food, semiconductor) and the general inventory was largely not met.
Shanghai-based Selective Technologies usually helps clients to get a clear view of the equipment bill and existing spare parts inventory, and decides whether to go to the last complete system or from key modules — for example, to get on the equipment board and alerts, and then connect to the worksheet. This is small, it works fast, and it doesn't push the current process back up.
Return to the two-point call at the beginning of the morning -- if there was a system in the warehouse, the spare parts were positioned, model matched, and call records should be done within minutes. The input for the spare parts management software is not necessarily expensive, but it's clear that after the time you put it to the place: less time to stop the equipment, lower use of spare parts funds, and documented maintenance costs.

Ms. Lei
Mr. Pang