Running RFID Asset Counts with Zone Scanning and Data Synchronization
Industry News

Running RFID Asset Counts with Zone Scanning and Data Synchronization

PublishedShanghai Zejie Smart Technology Co., Ltd.

The system has dozens of duplicates in the warehouse after a walk-through with the handler, often not because the label is invalid, but because no area was defined before the inventory, there was no control to read and no duplicate data were processed after the inventory. The RFID asset count is usually performed as “Build task—Scanted partition—on site review—data synchronized-discretion” (the “Data synced-discrepancies”).

Problems at the scene: people are gone, data is not up.

A storage area of approximately 2,000 square metres, shelves, swing space boxes and equipment to be repaired are stored simultaneously. Staff members pass through the channel with their hands-on RFID readers, and the screen constantly ejects asset numbers. Upon return to the office, the number of counts differs from the asset desk account: some assets are read over again, some assets are scanned in the adjacent area, and some labels are read out without corresponding asset records.

The core of the RFID inventory is not " how many times have you read it " , but rather " which assets are effectively read within a specified time frame and within a defined area. A valid record should contain at least an asset number, an inventory task number, a regional number, reading time, equipment number and operator. Without space and time, it is difficult to follow up on whether the asset actually moves or whether the wireless signal is captured in the adjacent area.

Preparation before stocktaking: delineation of mission boundaries

Before the inventory is started, the administrator needs to create an inventory task in the system, set a name for the task, take an inventory range, executer and deadline. The range can be divided by warehouse, floor, room, shelf or device type, but the field identification must match the area code of the system.

Preparation of projects Field practices Check results
Asset desk accounts Collating asset numbers, names, areas, status and label numbers An asset corresponds to an identifiable label number
Regional division Clear coding of access, shelf, room or equipment area People can determine where they are by code.
Equipment inspection Confirm handheld power, network, reader connection and time setting Test labels can be read and uploaded steadily
The unusual list. Advance listing of assets pending maintenance, loan, storage and hold-over Clear comparison of the differences in the inventory

The labels are also uniform. Metal equipment usually uses a label of the metal surface, liquid containers, and dense stacking items are subject to field testing to determine the location. The labels are not placed in areas that are easy to bend, cover or frequent friction. This is recommended for implementation on site, which should be based on actual reading of the test results.

Shanghai-based Chettech, while combing the inventory process, puts "assets table booking" and "read-and-read tests" before a formal inventory. The value of this is that people on site do not misjudge system infrastructure issues as equipment or labels.

Field operations: scan by area, control reading range

After entering the inventory, the staff member selects the current area on the handheld and then starts scanning. The device moves along a fixed route, after a few seconds of suspension from a shelf or group of devices, confirming that the reading quantity is stable and then going to the next segment. The time of stay here is not uniform, and should be adjusted for label density, shelf material and site interference.

  1. Checks the area code displayed on the handheld to confirm that no adjacent inventory is in place.
  2. Start scanning and move through asset position along pre-set routes.
  3. Observe changes in the numbering, repetition and signal strength of new numbers, avoiding looking only at the total number.
  4. Border positions, cover positions and high-value assets are cleaned at close range.
  5. Saves the record after closing the current area and then switch to the next area.

The handheld reads the same label many times, which does not mean that the system should generate multiple asset records. Data layers are usually based on " take-up task + asset + area number " ; the same asset is read multiple times in the same task, can be kept for first reading, most recently at time and number of readings, and the final count results are maintained only one valid asset record.

A nearby area is the easiest to ignore. When a warehouse channel is narrower, you can reduce the reading and writing power, shorten the scanning distance, or use partition doors, block materials and direct operations to control the read range. Parameter adjustments should be based on test results, not only with the device defaults.

When discrepancies occur: do not modify the desk account directly

After the inventory is completed, the system should compare the reading results with the asset desk account in at least four categories: normal inventory, surplus, loss, and region inconsistent. The gain represents an asset that was not read in the account; the deficit indicates that the account existed but was not read this time; and regional inconsistency means that the asset number exists, but the area of reading differs from the registration area.

Type of variance On-site review modalities Process Action
Unread To Check lending, maintenance, storage records and review them in the original area Fill out the reason, not remove assets directly
Extra assets Check tag numbers, asset inscriptions and temporary storage records Checking the list once identified
Regional inconsistencies Confirmation of redeployment or temporary movement of assets Update of regional information after clearance by the responsible person
Tag Malformed Check label break, block, drop and install Subsidize or replace labels and keep a record of changes

On-site review, you can have operators read the unusual asset in a single piece of close range, then take an asset stamp or record physical location. Photos, reviewers and review times need not necessarily rely on RFID devices to collect them, but may be supplemented by mobile forms, which is crucial for every change in account to be traced.

Data synchronization: separation of offline records and official entry

When the warehouse network is unstable, the handheld should support offline preservation. Offline records cannot directly cover server accounts, but should be accompanied by local task numbers, equipment numbers, collection time and data status. Once the network is restored, the system is processed in the order of uploading-checking-de-referred-reviewing.

  1. Upload:Uploads the new local record to the server, and the failed record is kept in the queue awaiting upload.
  2. Verify:Checks the completeness of asset number formats, task numbers, area codes and time.
  3. Go on, get it!Duplicate records identified by mandate, assets and regional configuration.
  4. Match:(c) Generates normal, surplus, deficit and regional inconsistent lists.
  5. Audit:Only authorized persons can update the status of assets, their area or their label number.

Synchronize to avoid "repeated click upload" creating duplicate data. It is more prudent to set the single current number for each collection record, only once the server receives the same stream number; when upload breaks, never-recognised records continue to be sent instead of rewriting the whole batch.

If the interface between the asset management system and the inventory system needs to be synchronized, it is recommended that the field correspondence be clarified, such as the asset number, label number, area code, asset status, time of inventory and review results. The interface returns successfully and does not amount to a business audit completed, and the system should also maintain the original logs and audited desk results for follow-up purposes.

After stocktaking: use the results to drive the next round of improvements

When a round of inventory is completed, do not export only one number of "accumulated" numbers. More useful results include the total number of tasks, effective reading of assets, unreading of assets, duplicates, regional inconsistencies, label anomalies and pending quantities. For duplicate records, the proportion of readouts can be counted; for unread assets, a distinction should be made between physical in-situ presence, damage to labels, area changes and field leaks.

If there is more serial reading in a region, the problem may be at the zoning boundary or equipment parameters; if some type of asset is often unreadable, it may be related to label material, location of installation, or how the device works. Categorizing differences by region, asset type and cause, the next inventory can be tailored to adjust the route and review rules.

When you actually land, you can select a region for small-scale testing, confirm tag installation, scan distance, offline save and synchronize rules, and then expand to the full repository. The key to RFID asset inventory is to get read on site, the system compares with manual review using the same numbering and area rules; the process is clear, data synchronization does not become a new source of error.