What about the RFID CD reader? Model parameters and deployments
1. Set the scene and then compare the parameters
Many people are stuck in the parameter table at the request for quotations, looking at the numbers "reading distance of 10 meters" and 500 tags per second. The number actually is set on a condition: label size, chip model, antenna gain, radio frequency power, or any shielding of the metal environment, which makes the difference between real and nominal distances.
It is suggested that the scene be clearly defined in three steps:
The first step is to look at business.The bulk gate is set up with a fixed one-line antenna and spreads the shelf holder back to blue teeth.
The second step is to look at existing label stocks.When you take over the old project, confirm the tag protocol and frequency: EPC Class1 Gen2 / ISO 18000-6C is the mainstream, with a few older systems still in ISO 18000-6B. New readers must be compatible, otherwise changing labels may cost more than changing readers.
The third step is to look at the access system.The inventory data is ultimately going to ERP, WMS or the self-study platform? The protocol interface (LLRP/RESTful/MQTT/OPC UA more commonly) supported by a reader determines whether the project can land. This item is more important than the rate of reading.
2. What do core hardware parameters look at?
The following is a list of the most recent items on the website:
- Working band.The UHF frequency band covers 840-960 MHz, which is commonly used in mainland China 920-925 MHz, and the European and American range 902-928 MHz, which is to be transposed by confirming that the solids are available for transposition.
- Radiofrequency power.Typical 0-33dBm is calibrated, the higher the power, the greater the metal reflection, the more it needs to be in the environment.
- Receive sensitivity.Good solutions can be found around -82dBm, with ordinary programs in the range of -62 to -75dBm, and sensitivity directly determines whether weak labels are readable.
- Number of antenna ports.The number of ports is common at 4 ports, with a split host between 4 and 16. The more single stations are covered, the greater the power will be distributed.
- Single-label reading rate.Typical 100-200 seconds, when the inventory label is dense, the rate determines the entire inventory cycle.
- Multiple labels are collision-proof.The same area labels exceed 200 depending on whether Dense Reader Mode and a robust collision-proof algorithm are supported.
- interface type.The industrial class is typically accompanied by G-G-E-net plus RS232/RS485, with portable belts Wi-Fi, Bluetooth, and 4G. The distance above 100 metres suggests fibre or Ethernet.
- Protection level.The storage site IP54 starts with an IP65 for outdoors or cold tanks, and the working temperature is checked to see if −20°C to +60°C is sufficient.
- Power supply.A fixed multi-support PE (electricity with an etho-net) with a simple lined line; handheld machines are more comfortable for the single charge support of 8 hours or more.
- Standard of agreement.The EPC Class1 Gen2 / ISO 18000-6C is a current default requirement, with potential for self-owned agreements in special industries (air baggage, books).
Shanghai-based Selective Technologies found in the integration project at the warehouse and manufacturing site that most of the problems were not from the reader itself, but rather from the protocol intermediate and upper WMS. So after reading the specifications, one more question is: Can you provide a development document and an example code?
3. Deployment of the environment and antenna programme
Readers are chosen only as a start, and deployment is the place to really see kung fu. Antenna selection and placement often have more impact than the brand itself.
The shelf scene.A flat-span antenna is projected to be pushed down at the top of each shelf, covering a width of about 3-5 metres. The common gain is 8-12dBi, and the increase in the increase is being narrowed and condensed, balancing the width of the cover with the permeability.
The gate tunnel scene.Each side of the doorway contains 1-2 Circumpolar antennas covering the direction of the car. The Circumpolar antenna is not sensitive to labels, at a cost of reading distance at about 30% of the polarization line.
Metal environment.Metal shelves, metal trays reflect frequency, causing blind areas and multi-routing interference. Our approach is to draw a grid on the ground, test the RSSI values by point with a portable reader, find the actual readable area, then determine the antenna position, instead of an equal distance from the drawing.
Cold storage with outdoors.Watch if the working temperature of the module covers below -25 °C, and industrial readers are usually fine, but LCD screens and batteries are decomposition at low temperatures.
Interruption of the screening.The two adjacent reading and writing machines overlap with each other. Planning frequency points (generally 4 channels) and opening Dense Reader Mode can be mitigated, and large warehouses suggest a spectrum scan first.
4. Several accounts in cost structure that are easily ignored
The unit price of hardware is only a surface level and the budget is often set aside for:
- Antenna and feeder.Industrial-grade UHF antennas vary from $300 to $1,500 each, with a feeder of several dozen dollars per metre. More than 5 metres recommend low-depletion lines, otherwise power decline is significant.
- Install debugging.Fixed slabs, lines, lined-up cabinets are estimated at 8 reading and writing points in one warehouse, and installation debugging costs usually account for 30 per cent - 50 per cent of the cost of equipment.
- Intermediate and interface development.The RMTful interface to WMS/ERP often involves data cleansing, weighting and de-logical. Simple RSTful interfaces work one week, with complex two-way synchronization likely to be more than two weeks.
- Spare parts and maintenance.The reading and writing equipment itself has a low failure rate, but the antenna port, industrial connectioner is oxidized by frequent interplugging and is recommended for annual spare parts of 5 per cent-10 per cent.
5. Several pits common in the actual project
- Only focus on the nominal reading distance.The 10 m in the specifications is the result of air-free, 96 x 24 mm tags with maximum power and usually only 3-5 m in the warehouse, which is recommended to be tested on site with a sample.
- Ignores label consistency.Different manufacturers even have different batch labels, with a deviation in sensitivity and frequency. It is recommended that 1,000 pieces of the mass be measured after delivery, and that the normal distribution of sensitivity be measured.
- "Readed" as "reads right."Repeated, missing and multiple readings are common and require re-engineering and validation at the middle level. It is recommended that readers or intermediates support RSSI filtering and reading thresholds.
- Ignoring electromagnetic compatibility.The large warehouses have a frequency transformer, server, Wi-Fi AP that can cause disruption and, if necessary, spectroscopy to find a relatively clean band.
- Network reliability is assumed to be too full.The key scene suggests a 4G link emergency response by going through the cable Ethernet.
6. Steps that can be implemented immediately
Define the use case, map the stocktaking workflow, and write down the three most important acceptance criteria. For example: at least 99% successful reads of entire pallets in one pass, no more than 10 minutes per count, and no more than five operator steps.
Bring a demo unit on site and test for at least three days, covering regular shifts and overtime. Log missed reads and stray reads.
The manufacturer is required to provide the protocol intermediate file and at least a set of reference access cases, with the manufacturer ' s engineer being involved in interfaces as necessary.
By doing this, the selection is no longer a comparison of the argument tables but rather a comparison based on the scene, parameters, costs and risk tables.

Ms. Lei
Mr. Pang