nfc High temperature label material options and work selection
RFID Knowledge

nfc High temperature label material options and work selection

PublishedShanghai Zejie Smart Technology Co., Ltd.

Select PET, PPS or PI material to see not only how much the labels can bear, but also to check the chip's temperature-resistant, glue-resistant, metal-based environment and reading time.

Cost: How does a normal PET trade off with high temperature base materials

The cost of materials is usually calculated on the basis of "basics, chips, antennas, glues, process." PET labels are mature, flexible, suitable for mass applications that are cost-sensitive and less temperature-sensitive; PPP, PI and ceramic base materials are more heat resistant, but materials, composite and encapsulation processes are more demanding, and single costs tend to rise.

Programme Common temperature focus range Cost characteristics Appropriate procurement logic
Change PET -40°C to 85°C, some products may be shorter and higher Material and processing costs are easier to control Short temperature, large mass, no direct contact with heat source by label
PPS Common use of approximately 150°C to 180°C, depending on the type More than normal film, suitable for a time of heat resistance and stability in size. Breadboxes, heat treatment equipment, repeated temperature rises and cooling
PI Common temperature tolerance range of 200°C or more, depending on the film layer and chip High material and processing requirements High temperature, thermal cycle, space limitation or need for thinner structures
- Ceramic seal. Fits to higher temperature or strong corrosive environment, and requires data for containment Higher cost of sealing and installation Metal components, strong rinsing, long-term high temperature and grinding requirements

The above table is a common range of public chips, base and glue technology, updated in 2024. Temperature zones cannot be directly used as purchase commitments, and the actual costs are also affected by label sizes, antenna forms, print content, starting order and field installation.

Effect: Temperature tolerance is not equal to stable reading at high temperatures

NFC uses 13.56 MHz for close communication. The label is not only read if the film is deformed, but also whether the chip is still in working temperature, whether the antenna parameters are changing, whether the duct is moving, and how far the label is from metal or liquid. The label looks intact after high temperatures, but the reading distance drops, and it still falls.

Actual differences in material selection

High temperature reading and writing also differentiates between " read after heating" and " read during heating. If the label is read after leaving the heat source, it is usually easier to reach a stable distance; if it has to be read at about 150 °C, read-and-written distance should be tested together with the time of reading and equipment window. Metal surfaces can be strewn or anti-metal antennas, but the thickness of the space layer affects structural dimensions.

Applicable scene: Type by temperature curve instead of single point temperature

It is suggested that the work be written in four terms: peak temperature, duration, frequency of circulation, medium contact. For example, "120°C, 40 minutes each, 8 times a day, exposure to a cleaning fluid" is more critical than just writing "120°C."

Work Priority The test focus.
Storage, swing tank, heat tracking PET or General Softness Label Dropping, friction, paste cleanness and reading distance
80°C to 120°C heater short Changed PET or PPS Heated reading distance, gel strips, label edges.
150°C or more, repeated heat cycle PPS, PI or ceramic seal Chip rated temperature, number of cycles, antenna resistance to change
Metal parts, cleaning or oil-contaminated environments Anti-metal Structure, PPS/PI or Seal Label Media impregnation, metal spacing, flush pressure and reading and writing angles

When Shanghai Selecting Tech Ltd. makes this choice, it is appropriate to draw the location and process of the label first, then to determine whether the tag is soft, anti-metal or sealed. The sample test should not be a single label, and it is recommended that the sample be taken in different batches, before the condition, during which the work is read separately, and to record reading distance, success rate and appearance changes.

Common pits: The material is selected correctly and the label may still fail.

  1. Just look at the base, it's cool, not the ceiling.The full temperature parameters should be requested, rather than the words “PI” or “PPS”, only.
  2. The peak temperature is considered to be continuous.“Establishing 180°C” may represent only short-term exposure.
  3. Ignore the glue.Common problems after high temperatures include softening, carbonization, rubber, arctics and stripping.
  4. The temperature distance is used directly.Temperature, metal and liquids change the antenna. If you want to read the device at a distance of 50 mm, you should have the corresponding residuals tested in actual installation status.
  5. The label size does not match the antenna scenario.Small size labels are more susceptible to metal and installation angles.

The actual selection is carried out in this order: Recording the temperature curve and medium environment; Validating the chip and glue Quantification parameters; Determineing whether or not to contact metals; Make at least two material samples; Complete thermal cycle, Sticking and reading and writing tests; and restructure according to the location of failure. The criteria are not "heat tolerance" for labels but, after a complete process, they remain structurally stable, stickers reliable and acceptable reading performance.