How do we do the RFID warehouse count? A mass reading program in the storage area.
The RFID area bulk count is not a simple replacement of "handheld long-range bar-scanning code". Its core is: stationary reading and writing equipment is deployed on the shelf at the top of the warehouse, labels are automatically read in bulk after they reach the antenna coverage, the whole process does not require manual scanned-by-work, and an inventory of a storage area is usually compressed from hours to minutes.
From "Land Sweeping": RFID read what it is.
Many people who first contact the RFID warehouse count, imagine it as "wireless bar code" -- handheld devices are all over the shelf. The practical principles are very different: UHF RFID labels do not have batteries in themselves, radio-frequency electromagnetic waves from the reader antenna are powered by the radio, and the stored EPC code (which can be understood as tag ID numbers) is drawn back to the readers in reverse dispersive signals.
Bulk reading means a reader can capture data from dozens or even hundreds of tags in a very short time, for example 300 milliseconds, using an anticollision protocol. Under EPC Class 1 Gen2, for example, the reader sends a Query command, tags respond in randomly selected slots, and the reader acknowledges them one at a time. The Q value governing the initial slot count and the algorithm together keep the probability of collisions very low. That is why you can push an entire cart through an RFID portal without lining up and scanning each item individually.
How do you set up the antenna in the storage area to actually "several read"
The hardware selection and location are among the most problematic components of the project.
- Gate-type access: Install one or two antennas on each side and at the top of the portal to form a read zone around the load. This suits entrances, exits, and inbound pallet routes. The downside is the footprint and the minimum clearance needed for forklifts and pedestrians.
- Top-Air Array: Install a round polarized antenna above the shelf to cover the reservoir position down. A stereo that suits the shelf ' s dense, cyclical inventory. The beam angle is 60-90 degrees and is adjusted for the layer height and the size of the store.
- Handheld + cart: A large change of the height of a large shelf or shelf, with a mobile reader. Flexible but less efficient than fixed.
At the site of the retrofitting of the storage area, the problem with the blind zone is typical: a large number of metal shelves on both sides are found at the site by using a generic approach, reflecting a 30-centimeter gap between the two sides of the corridor, where labels are repeatedly triggered and lost. The common practice of Shanghai-based Cheeky Way Technology Ltd is to be double covered by "door-type access + top antennas" and then take a tag test card and go over the cover sheet, instead of looking only at the parameters given by the factory.
Several parameters are often overlooked: Reader power is typically 0.5-2W, and the national flag's launch power for the UHF frequency band is limited to 2W ERP; antenna gain 6dBi-8dBi suits the warehouse; label side, tray-level metal selection label, single card box is simply a common inlay label, but goods containing liquid or metal beams need to be added to the gasket or select a special label.
Execute a complete process for the count
Put the program into operation, usually in five steps:
- Tab binding: The tag completes the EPC code for writing before entering the library, and with SKU, batch, the repository creates a map in WMS. The map is not valid, or read it or not.
- Trigger readingThe door-type approach is different depending on the programme. The path to the tray is detected by infrared or geosensor loop; the top-loading option is based on timed rounds, such as a 30-second sweep of the current storage area.
- Data ReturnReader transfers read EPC, time stamp, antenna number to midstream (middleware), which is rewrited, filtered and associated and written in WMS.
- Reconciliation of variancesWMS matches the actual read labels with the book inventory, and locates the difference to SKU and the repository.
- Aberrant arbitration: Deal with missing reading (the label was not read), rereading (the same tab was read in two antennas), and string reading (reading to the next vault). The rules are usually configured by intermediate, for example, multiple count times on the same label on the same day or only trusting the nearest library slot antenna.
A full inventory of the storage area, from start-up to generating a discrepancy report, typically takes 5-15 minutes depending on the size of the warehouse and the number of readers. This difference between the traditional manual count and the one that is so easily perceived by the business community is the most valuable point in the project.
A few parametric holes that can easily be stepped on.
More power is not always better. Above a certain threshold, antenna sidelobes can pick up tags in neighboring storage locations, causing stray reads. A common approach is to start at low power (0.25 W), increase it slowly until the read zone just meets requirements, then allow a 10%-20% margin.
The dynamic count is harder than the static count. If the reader is in motion (e.g. on a sorting line), the reading and writing window may only have 1-2 seconds, Q values will need to be lowered, the wheel will be increased and speed tested ahead of time. The static count (the goods on the library) is much more tolerant, with a stay of more than 1 second sufficient to read.
If you have a large area, the number of antennas is more than 20, it is recommended that a special RFID medium be moved.
The metal shelf, for example, a water/liquid product with high content (e.g. a drink, a liquid chemical), is significantly shorter to read distance. The metal environment is usually addressed by anti-metallic labels + mats (at least 5 mm above the surface); the liquid environment requires more permeable frequency bands or shielding material outside the label.
Project landing proposal
If the warehouse is ready to go to the RFID mass-reading program, it is recommended that a pilot be done in a single storage area, running through the full link of "label binding -- antenna deployment -- read-recognition-arrangement" and copying it to the whole warehouse. The pilot phase focuses on three types of data: cover maps (can you read from each of the libraries), missing reading rates (how many are known not read), serial reading rates (reading the wrong label). These three indicators are met, and we consider expansion.
RFID bulk count is not a single technology, but a set of systems that can be configured from label selection, antenna setting, intermediate to WMS docking. By aligning the hardware performance parameters with the operational rhythm on the ground, efficiency gains will really come on the books.

Ms. Lei
Mr. Pang