Active vs. Passive RFID Tags: Differences and Selection Criteria
First, answer the question: Should we let the label call you?
The core of the selection is one: you need a label.Proactive locationStillAsked by a reader and answered.The former selects active (active) RFID, the latter selects passive (passive) RFID. The active label contains a cell, sends a time signal with a reading distance of several dozen to hundreds of metres at a unit price of 30-200 yuan; the passive tag is powered by reader radio frequency, the UHF section reads 3-8 meters, and the single purchase order price is more than 0.5-5 dollars. Think clearly whether "active" or "passive awakening" lines are not rounded.
Element 1: Life expectancy and frequency of maintenance by means of electricity supply
The passive labels are free of batteries, simple structures, and life is determined mainly by physical wear and tear. Normal labelling can be used for up to 5-10 years. The active tags include buttoned or lithium batteries, the conventional product lasts 3-7 years, and battery depletion requires a full replacement, which is an obvious maintenance cost. There is also a semi-passive program, where batteries work only for chips, and communication is still activated by the reader, with reading distance between them, which are often used in cold chain labels with temperature transfer.
Element 2: The reading gap covers four typical scenarios
- Unsourced UHF (860-960 MHz): Reading range 3-8 m, dense-placed for warehouse, production line
- Source 2.4GHz: Open environment reading distance 80-150 m for vehicular access, long range identification
- Source 433 MHz: Reading distance 30-100 m, good permeability, for mines, tunnels
- Unsourced LF(125kHz)/HF(13.56 MHz): Read distance from centimetre to 1 metre for door-bargaining, payment, one cartoon
Point 3: The budget boundary is calculated first, depending on the cost or volume
Calculate reader costs and deployment density as well as tag unit costs. Passive UHF readers cost RMB 3,000–15,000 and require relatively dense placement. Active 2.4 GHz readers cost RMB 2,000–8,000 and cover more area per unit. With more than 10,000 assets, a difference of tens of yuan per tag can change the total by an order of magnitude. Check whether needing fewer readers can offset the cost of active tags.
Point 4: The scene is the hardest to step on.
| scene | Type of recommendation | Rationale |
| Warehouse Tray/Camberboard Point | Unsourced UHF | Batch labelling, low cost |
| Vehicle access to plant identification | Source 2.4GHz | You can read it in a few hundred meters. |
| Miners' underground location | Source 433 MHz | Good penetration and battery life of over three years |
| Retail/false prevention | Unsourced HF/NFC | Very low cost, compatible cell phones. |
| IT equipment/medical equipment inventory | Unsourced UHF or NFC | Home readable at short distances |
| Container transport full-way tracking | Source+GPS Group | Outdoor location + port of entry and exit identification |
Element 5: Environmental interference and label density are often underestimated
Metal and liquids attenuate RF signals. On metal, use tags with an absorbing layer. Even active tags should be kept out of fully shielded metal enclosures. Dense tags can collide when they respond together. Passive UHF's ISO 18000-6C (EPC Class 1 Gen 2) anti-collision algorithm can identify hundreds of tags in a pass, but poor antenna placement can significantly lower the read rate.
Point 6: Four-step judgment goes straight to the point.
- Count the distance.: to determine how far the reader must read the label, decide on frequency and whether or not to send a letter at your own initiative
- Look at the assets.: Whether continuous positioning (selection of active) or time inventory (selection of passive)
- The final payment.: Label unit x quantity +reader Z + Deployment + Maintenance, based on 5-year total holdings
- Sample test: special conditions such as metal, liquids and high temperature fungi are tested first, not directly listed
When Shanghai Zejie Technology helps manufacturers design RFID solutions, two selection mistakes come up most often. One is using passive UHF for vehicle identification, then having to add reader after reader because the range is too short. The other is putting active tags on racks that need batch counting, driving tag costs beyond budget. Decide first whether tags should transmit on their own or be activated by a reader, then follow the four steps above to stay on track.
Put the judgment logic in one sentence.
The passive RFID fits the "I go to find it" scenario -- warehouse, line, retail, 80% of the demand for asset counts; it needs a "it comes to you" scenario -- vehicles, people, long-range assets -- only sourced. First fixes distance and asset properties, then looks at budget and environment, which is the path to return to work at least.

Ms. Lei
Mr. Pang