What do you think of the erf rfid reader parameters, frequency-band capabilities and antenna selection points?
RFID Knowledge

What do you think of the erf rfid reader parameters, frequency-band capabilities and antenna selection points?

PublishedShanghai Zejie Smart Technology Co., Ltd.

Look at the URF RFID reader parameters. Which are the focus?

Look at the UHF RFID reader parameter table, the core is four: working frequency bands, launch power, reception sensitivity, antenna interface and protocol compatibility. Other things like working temperature, protection level, electricity supply are important, but the first four determine whether it can be used or not. The frequency segment determines whether it can be used legally locally, the power determines the distance to be covered, the sensitivity determines the ability to read weak labels, and the antenna and protocol determines the difficulty of matching existing systems. We usually do projects with a C-band and compliance, then we see the power and sensitivity mix, and then we pick out antenna configurations and interfaces.

How do we choose the frequency of the RFID? What's the difference between countries?

The UHF RFID frequency band is not global. The mainland China open window is 840-845 MHz and 920-925 MHz, with an equivalent total radiopower (EIRP) of 33dBm (i.e. 2W); Europe 865-868MHz, with a similar power limit of 33dBm EIRP; the United States 902-928 MHz, with a wider range but with a limited power to be adjusted with channel jumps. So if the bid "supports the global frequency band", it would essentially have to switch to different sub-frequency and power ceilings in different regions, otherwise it would have been irregularly used.

If the equipment is purchased in a cross-border scenario, it is necessary to confirm whether it supports frequency-band switching by hand-jumping, software configuration or automatic recognition. If used only at home, a device with 840-845 MHz and 920-925 MHz windows is sufficient, and there is no need to pursue full frequency bands.

What does a launch power and a reception sensitivity mean?

The launch power unit is usually dBm, 1 mW=0dBm, 33dBm equals about 2W. The general reader can adjust power by 0~33dBm, with more of the industrial model at 30~33dBm fixed output. The higher the power cover, the higher it reaches, the higher the intensity of the reading scene (e.g., a shelf-intensive warehouse) will be overpowered because multiple labels are responding to the leak, which will reduce power.

The receiving sensitivity is typically expressed in dBm, the smaller the value is the more sensitive, and the common level of industry is between -82dBm and -96dBm. High-sensitivity readers can read even further weak labels, with a clear advantage under unfavourable conditions such as metal masking, liquid environment or labeling on the outside side of a box. When looking at parameters, power and sensitivity are best compared to one-size high-power but generally sensitive equipment, which may not actually be read effective.

Which indicators do the antennas choose?

Antenna selection is the most easily pedaled link in the UHF RFID project.

The gain unit is dBi, which is common in the 6-12 dBi range. The higher the increase, the narrower the beams, the more far away they are, the smaller the angle of the cover. The view of the warehouse gate passing through the car usually chooses a panel antenna of 8-9d Bi, taking into account distance and the width of the cover; the shelf-intensive storage position recognition is better suited to the immediate antenna of 6-8d Bi, avoiding wave beam interference.

The polarization method is the polarization of the dichotomy and Circumpolarization. The Circumpolar antenna does not require a strict alignment of labels with antennas, and it is more economical to actually deploy them, so most reading and writing scenarios are defaulted on the rodiacization. The polar antenna gain can be high, far away, but the label position is relatively fixed, and it is appropriate to transfer the label to an identifiable scene.

The horizontal beam width and the vertical beam width are all looked at in the beam width. A ban on a car scene usually requires a horizontal beam width of 60° ~ 90°, or a vertical beam width of 30° to ensure that labels at different heights are read when the car passes.

How do we plan the number of antennas and their deployment?

Readers have anywhere from one to eight antenna ports, with four or eight common on industrial models. Port count directly affects coverage and the density of tags the reader can handle. Four ports provide coverage from four directions at once and suit most warehouse entrances and exits. Eight ports are better for wide portals or shelving that needs to be read from multiple angles.

When the antenna is deployed, the adjacent antennas are to be drawn at a distance to avoid interference with each other, usually at least half of the wavelength (about 17 cm in the 900 MHz band). If two antennas are to be hit in the same label area simultaneously, it needs to be switched over time by the multiple antennas from the reader, otherwise there will be a reading conflict.

We did a project for auto parts storage, which was supposed to cover 10 metres wide with a high-benefit antenna, and the middle position was badly missed, and then two 8dBi antennas were spread over the sub-region, and the rate dropped. In this case, the number of antennas is more important than single gain.

What is required for interfaces and protocol compatibility?

For interfaces, industrial readers are commonly found in Ethernet (RJ45), serial ports (RS232/RS485), USB, Wi-Fi, Bluetooth and GPIO triggers. Storage and production integration generally takes Ethernet and GPIO, which returns data, while the latter triggers PV sensors or PLC.

The protocol is based on the main EPC Class 1 Gen 2 (i.e. ISO 18000-63), and this is currently the type of air interface protocol that most labels support. It also confirms that the development interface provided by a reader, such as RESTful API, MQTT or OPC UA, is easily connected to WMS, MES. If only the manufacturer ' s SDK protocol is supported, the integration costs are much higher.

What are the problems that can easily be overlooked in actual use?

The list of parameters looks good, and there are a number of cases of flipping after deployment.

How can we verify that the equipment is really sufficient before it is procured?

The parameter list can only be used for a preliminary sift, and really decides whether it can be tested on site. It is recommended to take its own labels and actual goods, and to do a round of POCs (Proof of Concept, or conceptual validation) at the plant or integrator's laboratory. Focusing on three: reading distance limits, leakage rates from dense labels, and recognition rates for dynamic scenes (e.g., in transfer belt motion).

If the project is so reliable for reading, such as air baggage separation and medical retroactivity, it strongly recommends that a small batch of 2-4 weeks be tested for bulk procurement. When we select a client, we usually prepare two to three alternative brands for comparison, and single brand tests are vulnerable to individual differences.

Matching the parameters and scenes is all that matters.

Summarizing: The parameters of the UHF RFID reader are not hard to read, and it is difficult to match them with the top-numbering of your actual scene. First, you have to comply with the frequency, then see if the power and sensitivity mix is reasonable, and finally, according to label postures, coverage and system integration requirements pick antennas and interfaces. The parameter is only a starting point, and mapping is the key to determining whether the project succeeds or fails.