rfid chip selection resolution: frequency band, capacity versus manufacturer programme technology
RFID chip selection, frequency band, capacity, which protocol should be prefixed?
Set the frequency band, select the protocol, and then see the capacity. The frequency range determines the doorbar, storage, medical backslides, vehicle recognition of these different scenes that run; the size determines how much business data this chip can save; the agreement determines whether it connects with existing readers. In the wrong order, the downstream is either re-released or rewiring.
Three bands, low frequency, high frequency and UHF, do you know where to distinguish?
The RFID chips are divided into three main groups by frequency of work: low frequency (LF, about 125 kHz), high frequency (HF, 13.56 MHz), hyperfrequency (UHF, 860-960 MHz). They are completely different in their permeability, reading distance and adaptability to the metal and liquid environment.
Low frequency 125kHz:The advantage is that it works with a high degree of resistance to interference, which allows for penetration through water and metal casings. It is used in early door-barrel cards, animal earmarks, car theft. Typical storage ranges from 64bit to 1KB, and slows.
HF 13.56 MHz:The read/write range is about 10 cm to 1 m. The main protocols are ISO 14443 and ISO 15693. The former is used for ID cards, transit cards, and multipurpose access cards. The latter is used in libraries and smart shelving. Capacity ranges from 1 KB to tens of kilobytes and can hold small amounts of structured data.
UHF 860-960 MHz:Reads can be as far as 3-10 meters or even further, and is a logistics warehouse, retail inventory, production-retroactive primary frequency. The mainstream protocol is the EPC Class-1 Gen-2 (also known as ISO 18000-63), with capacity ranging from 96bit EPC to several kBs, focusing on long-range mass reading.
A simple comparison:
| Frequency bands | Typical frequency | Read Distance | Typical scene |
|---|---|---|---|
| Low frequency LF | 125–134kHz | <10cm | Animal earmarks, door-bargaining, car keys. |
| HF HF | 13.56MHz | 10cm–1m | Documents, ticketing, books, linework. |
| UHF UHF | 860–960MHz | 3–10m | Warehousing, retailing, vehicle identification, pallet traceability |
The larger the storage capacity, the better? How do you rate the usual slots?
No. Choose only as much capacity as you need. Extra memory is wasted. RFID chip memory serves two purposes:
- Unique identification area (UID/EPC):Only one non-repeated ID number is used, and 96bit is the only one in the world. The low frequency chip is a few dozen bits, with HF and UHF generally 96-128bit.
- User data area:The capacity used to write business data, such as batches of products, dates of testing, maintenance records, ranged from hundreds of bits to a few KBs and was even larger.
Common capacity slotting and application counterpart:
- 64bit–1KB:Pure marking, animal earmarks, single items of security are sufficient.
- 1–2KB:HF door-barrel, small ticketing, smart shelf goods.
- 4–8KB:The only medical devices are the UDI, book management, and small-scale equipment.
- 64KB - Several MB:Near NFC tag capability, available files, graphic thumbnails, more for equipment matching and anti-false trace link vouchers.
If you just want to "sweep up and know what" the 96bit EPC adds a small number of user areas; if you want to "scanning up and see full production resumes," at least 4KB starts. Blindly pursuing large capacity will have two problems: one is going up on a single piece, and the other is going to be written longer, affecting the initial efficiency of batch processing.
What's the difference between the manufacturer's program?
There are a number of programmers doing RFID chips on the market, with differences concentrated on three levels: protocol compatibility, read-and-written sensitivity, and long-term supply stability. I contrast them in abstraction into three types of scenarios, avoiding direct branding.
Programme A: Universal-type HF tag chip
ISO 14443 Type A/B or ISO 15693, with a capacity of 1-8KB, has high price transparency and a relatively mature supply chain. Fits to door-barrel, ticketing, a cartoon such as a cost-sensitive bulk project. The problem is that the details of each agreement vary, for example, collision prevention mechanisms, inconsistent password authentication, and occasional compatibility problems when reading and writing across firms.
Option B: UHF Gen-2 generic chip
This type of program is based on the EPC Class-1 Gen-2 standard, 96-128bit, 512bit to KB in user area, suitable for logistics, retailing, asset management. The programs have been fast in recent years, with little difference in read-written sensitivity, and focus on containment (inlay, paper labels, metal resistant labels) and supply cycles.
Programme C: Specialized/Security Chips
Supports state secret algorithms, hardware encryption, and non-removable areas or anti-cloning characteristics. The capacity is usually larger, partly supporting the NFC Forum Type 5 standard. For financial vote certificates, drug traceability, electronic documents, etc., the price is typically 3-10 times higher than that of a generic formula.
In the old RFID project, Shanghai-based technology usually first sharpens the four types of applications, reading and writing distance, data volume, security level, then matching specific models with this three-dimensional framework instead of making blind selections of brands.
What are the three most easily stepped-on pits when choosing a model?
Pipe I: Ignore the metal and liquid environment.The UHF tags are placed on the metal surface or liquid packaging, and read-out ranges shrink from 5 m to several dozen cm. The solution is to bubble cotton with a metal resistant label or between a label and a metal instead of replacing it with a low frequency coupling.
Pipe II: The lack of clarity in the protocol leads to incompatibility with the reader.The chip also marked "13.56 MHz" has ISO 14443 and ISO 15693 protocols, and the reader supports only one of them without any reading of the other type of card.
Pit Three: Underestimation of the amount of work to be done for initialisation of labels.10,000 UHF tags are written in one piece for hours. The bulk project is to select the type that supports Block Writer or fast-coded, and to plan the sequence and validation of data in advance. The larger the capacity, the longer the single piece is written.
What's the order of the selection process best?
- (c) Determination of frequency bands: viewing the scene distance, looking at environmental disturbances and seeing industry compliance requirements (e.g., air, rail exclusive frequency limits).
- Determination of protocols: Reference to existing readers, customer-to-peer requirements for interoperable upstream and downstream, compliance system.
- Determination of capacity: Estimating an additional 20 per cent redundancy in the bytes of individual data.
- Inlay, non-dry glue, plastic cards, anti-metals, anti-liquid.
- Small batch test: Physical reading and writing tests are performed for each parameter, recording the time of the volume code and the success rate of the read.
After these five steps, the RFID chip selection is hardly problematic. The rest is supply chain and cost negotiations, suggesting that at the trial stage, two or more compatible models be locked in to avoid a single source of loss.
If your project is evaluating the program, you can send a description to experienced programmers, so they can give advice on frequency bands, protocols, three dimensions of capacity, and then do next physical tests. Read here, you should have seen how to bypass common pits, and the key is to think about the frequency bands and protocols before they are.

Ms. Lei
Mr. Pang