Type elements of the rfid tag handheld and fit analysis of the operation scene
RFID Knowledge

Type elements of the rfid tag handheld and fit analysis of the operation scene

PublishedShanghai Zejie Smart Technology Co., Ltd.

The RFID handheld type is a model that doesn't have "a table of parameters" -- and the parameter is beautiful, and it becomes a short board in an unmatched scene. It's a more prudent way to read the work scenario as what, how far, how much, how much, how much, how, at a time, to read "four things," then to pick out the type against the device parameters. We've been helping store, make, retailed down, and this idea has been less peddled.

Step 1: Break down the work scenarios

Before you pick out the model, think about the site.

It would be much less costly to write the answer on a whiteboard and then cross-check the manufacturer's data than to send the directly requested e-mail.

Read performances should not be limited to maximum reading distance

Many product pages simply say 'up to 8 m.' That range is often measured in a lab with no interference and a single tag facing the antenna. Reflections from metal, absorption by liquids, and collisions among tags cut real-world range. A reduction of 30%–50% is common.

Three things should be more important when looking at the parameters:

Before choosing the model, it is best to have the prototype run by the manufacturer to its own warehouse, simulate 50 stacks of labels and see if you can read them in 3 seconds.

Three defenses and a continuation of course, two that are the easiest to underestimate.

Three-dependency writing IP65, IP67, one difference is very large:

The drop-and-default value also depends on the number: 1.2, which is a common industry specification. If you are often to operate on steel frames of about 1.5 meters, you are advised to select the type of machine that will be tested for 1.5 metres or even 2 metres.

For battery life, retail store inspections involve about 1,000–2,000 scans a day, and 3,000–4,000 mAh is generally sufficient. Cold-chain counts may involve continuous bulk reads through a whole shift. Use a dual-battery setup of at least 6,000 mAh that supports hot swapping. Being able to change batteries without powering down is vital for round-the-clock operations.

The system is often more time-consuming than the equipment itself.

The availability of hardware is only the first step, and whether or not it can be connected to WMS (warehouse management system) or MES (manufacturing implementation system) is key to a project's real landing.

There are a few things to be sure about when choosing the model:

Integration labor typically costs one to two times as much as the equipment. Spelling it out in the contract up front avoids disputes later.

The direction of the arctics is often ignored.

UHF antenna splits polarize and circle. Linear polarized reading distance, but very directional, labels must be fixed to the antenna for reading; Circumpolarization takes a partial reading distance in the direction of tolerance, and the label can be swept from any angle.

Experienced this choice:

The two antennas are partly supported, while some require a change of machine.

Weight and a sense of control are a matter of time and time.

The difference between 400 and 600 grams may look small, but it is noticeable after eight hours of holding a device one-handed. In the projects we reviewed, staff often rejected a model because it made their wrists ache, not because it failed to read tags.

A few details can easily be stepped on:

Before bulk purchases, a prototype was used for one week for first-line staff to hear the real feedback and then to write down a list more directly than any technical parameter.

Budget allocations, less hardware and more services

Finally, many procurement managers have gone through this curve: they have put a large budget on the purchase of equipment, debugging it, redevelopment it, and training it has been reduced.

The more rational allocation of experience is as follows:

When Shanghai Selecting for Technological Co. Ltd. offers its programmes to clients, it usually puts this percentage in advance of the contract and avoids the embarrassment that "hardware acceptances pass at a later stage of the project but the system cannot run" .

Several landing reminders

If you're choosing a model, then in that order, you can make a lot less of the pits:

  1. Write the operating scene into a list of needs for rows 4-6.
  2. The two or more plants were allowed to carry a sample machine to the field and recorded three data: single-reader, group reading pass, full power hours.
  3. and WMS/MES manufacturer confirm interfaces to put data protocols in the document.
  4. Lists the concerns of 3 first-line employees (weight, key button, screen resolution) and let them try for a week.
  5. The budget is allocated broadly at 5:3:1.5:0.5.

The RFID handheld is not a consumer electronic product, and there is no "step-in" model, but it can be selected as a real device that can run through the working life if the scene is detached, the docking path is clear and the budget structure is sound.