nfc labels detailed: electromagnetic sense should be adjusted to load
RFID Knowledge

nfc labels detailed: electromagnetic sense should be adjusted to load

PublishedShanghai Zejie Smart Technology Co., Ltd.

Many people think that the NFC label is "actively launched after being scanned by a mobile phone," which is not true. The passive NFC tag does not have batteries, the reader builds a metamagnetic field near 13.56 MHz, the label wires get energy through electromagnetic sensors, and then reverses the magnetic field by changing loads to allow the readers to recognize data. The electromagnetic sensor is responsible for powering, and the load adjuster is responsible for retransmitting information.

EMP: Why can't the labels work with batteries?

NFC's current communications are based on a magnetic coupling between the wiring, rather than an antenna-to-space radiation wave like long-range radio. Reader and writeer wires connect to high frequency traffic currents, and they form a transmagnetic field around them; labels enter this magnetic field, creating sensor voltage. The tag chip puts this part of the communication through currents, stabilizes pressure, turns it into a direct current that can be used by internal circuits.

The basic circuits for labeling are usually coil, resonance, current-flowing circuits, voltage circuits, storage units and modulation switches.L# Resonate the conestro-capacitationC, the frequency of the vibration can be estimated below:

f = 1 ÷(2π√LC)

When the hype is close to 13.56 MHz, energy exchange efficiency between the coil and the cones improves, so it is easier for labels to obtain available voltage from a reader's magnetic field. The actual design also takes into account the electrical resistance of the coil, the resistance of chip input, the deviation between the containment material, the shift between the metal environment and the coil, which cannot be directly shaped by formula alone.

13.56 MHz has a free space wavelength of about 22.1 m, but the NFC labels are often only a few cm from a few metres away because they use a close magnetic coupling between the reader and the label. Increased distance, with a mismatch of the coil or the size of the coil not matched, reduces the coupling, and the energy obtained by the labels. The above frequency and wavelength data are based on: NFC radio frequency working parameters, 2024.

Consonance matching: how the coil and the cones determine the reading effect

The labels are not as big as they look. They're larger, they can increase magnetic fluxes, but they can change the sense of electricity, and the overall comphony points of parasitic and labels; they're too small to get enough energy. Engineering generally requires measuring the wires both, the quality factors, the frequency of the condensation and the chip load, rather than looking at the outer size of the label.

The labels, when near the reader, change the equivalent parameters in the surrounding environment. Paper, non-metal materials such as plastics, usually have less impact; metals generate vortex, absorb and disturb magnetic fields, deviance the frequency of vibration, lower quality factors, in the form of shorter reading distances, and unstable reading. If labels must be placed on the metal surface, they usually need to be accompanied by magnetic separators, and reorming the coil and matching parameters.

A label is read in a free space, not to say that it has the same effect on the actual object. The test should cover at least empty loads, material attached, target metal pieces, and several states of different angles and distances. Shanghai-based Cheeky Way Technologies, Inc., also includes materials and installation positions in radio frequency tests, rather than just verifying whether the chip can be read.

Load modem: how to transfer data back without a transmitter

When the label is energyed, the chip is cyclically connected or disconnected from an additional load according to the bit data that you want to send. This action changes the equivalent of the label's loop, and allows the currents, ranges or phase changes that you see in the reader's circle. Readers detect these changes, then restore the data transmitted by the label, which is what you do.Load Mode。

And you can understand that it's a two-person flexible rope: the reader continues to provide "thrust," and the label does not need to send a strong signal on its own, but simply changes its role in the ropes in a regular way, so the reader can judge the information from feedback. The energy of the label is weak, so the receiver circuit for the reader needs to be more sensitive and de-scrutize through filtering, decomposing and verifying the noise effects.

In common 13.56 MHz contactless communications, a tag can reply by generating sidebands through load modulation. Some schemes use a subcarrier at about 847.5 kHz, obtained by dividing 13.56 MHz by 16. Modulation, coding, frame formats, and rates differ by protocol and card type, so not all NFC tags use the same circuit. Parameter source: contactless card communication specifications, 2023.

A reading process: how energy, commands and data interact

  1. Establishment of a frequency field:The reader output the payload near 13.56 MHz, and the label coil senses an exchange voltage.
  2. Start chip:The label is fully current- and pressure-rigid, and when the internal voltage reaches its terms of reference, the chip is wired.
  3. Identification and selection:Reader sends a device recognition command on the site, and selects each one by conflict-proofing process when multiple labels exist simultaneously.
  4. Read or write:Reader sends a access command, and the label returns the storage area, status word or application data according to the protocol.
  5. Validation results:The frame of communication usually includes a check-up of fields and response mechanisms, whereby the reader determines whether the data need to be reissued.

Using a tag number of a web site or device, for example, the chip is not automatically broadcast all stored content on its own, but waits for the reader to give the command and return it in the prescribed data block and frame format. The reader may also read the contents as explained by the application layer, e.g., explaining the text record into a web site, numbering or status parameters. NFC itself is responsible for close communication, whether the data is encrypted, whether the memory is based on the core capacity and upper-level application design.

Common NFC communication rates include 106 kbit/s, 212 kbit/s and 424 kbit/s, depending on the type of protocol used and equipment capacity. Increases do not equal a synchronisation of distance because of co-location of major recipient circles, strong field, matching and environmental impacts. Rates, modeming and frame structure parameters are based on: NFC Digital Protocol Technical Regulation, 2024.

Key factors affecting reading distance and stability

When you are searching for a problem, you can test it in the order of "Aerial Label - Attaching Materials - Complete Products". If you can read it empty, post-readable, the problems are mostly found in materials or installation; if the reading distance is always short, you should check the wires, the concussion frequency, the quality factor and the field of readers.

From the rationale to design: how to select the right label

When close-to-reach identification is required, the focus is usually on reading distance, space and storage capacity; when writing data, the storage area structure is confirmed, the way it is protected and the data life; when door-barreling, payment or sensitive information is involved, the encryption, key management and anti-replicability should be assessed separately. The label works not only by chip type but also by coils, whether the containment and use environment match.

The design certification forms a basic test form: record the frequency of vibration around 13.56 MHz, the teleosphere electrical sense, the quality factor, the reading distance at different angles, the adhesion material, the number of consecutive readings and abnormal retries. These results are evaluated with the actual location of the product in order to determine whether the label is stable in the mass structure.

The NFC label is understood to capture two main lines: the electromagnetic sense addresses "how the label gets energy," and the load-modulation addresses "how the label can get data back to the reader." The former decides whether the tag can start, while the latter determines the quality of communication. The actual selection and development should be based on a 13.56 MHz resonance, collage of the wire, material impact and protocol needs.