What are the conditions that high temperature-resistant electronic labels can be used in: sterile, oily and metal environments
The label "fear" is not about the heat itself, but about the whole chain of material to be sealed.
Many people think that high temperature electron labels are just a little bit of welding, but the core problem is in materials: chips, baseware, antennas, seals, and each link is a problem at high temperatures. The normal RFID tag starts to drop the chip welding point at 85°C, the base layer, the antenna resistance to drift, the real way to hold the fung-cane, oil-infiltration or metal surface reflections, which are all matched from the cell selection type to the antenna design. Here's what the three typical scenes of the metal surface are doing.
The fungicidal scene: 121°C steam, gamma rays, hydrogen peroxide, which is the worst?
The challenge to labels is not just temperature, but temperature + humidity + chemical media.
- High temperature vapour sterilisation: Usually 121 °C/30 minutes, some of the instruments are fertilized to 134 °C/3-5 minutes (cf. EN 285). The labels carry both wet heat and repeated pressure changes, and generally use PI (polymamine) rather than PET for labeling material that can pass this condition.
- EtO: Temperatures are about 55-65°C, but the chemical medium penetrates common plastic and the gel layer becomes fragile after repeated sterilization over a long period of time.
- Gamma-ray or electro-beam irradiated fungi: It is carried out at constant temperatures, but a cumulative dose of over 25 kGy (reference ISO 11137) degrades the general chip wrapping material.
- Hydroxide plasma sterilisation: The temperature is lower (approximately 45-55°C), but the high oxidation can corrosive the exposed welding point.
Tags used to track surgical instruments are usually required to withstand at least 100–200 high-temperature steam cycles. When planning deployments for medical device customers, we recommend confirming the sterilization process and cycle count before selecting the tag grade rather than specifying the highest grade across the board. Radiation-resistant chips typically cost three to five times as much as standard chips, so there is no reason to use them where they are not needed.
Oil-contaminated environment: labels are not about oil, but about repeated erosion of cleaning agents
Oil-contaminated conditions are common in machine workshops, car parts and components, slaughtering partitions. These temperatures are not always high (often 60-100°C), but oil-contaminated + detergents are more dangerous. Many of the good tags on the floor, which can cause problems by moving to food partition lines, and they are chemically resistant because they are not hot.
Several actually easy-to-penetrate pits:
- The normal epoxy resin is packed in a few dozen impregnated acid detergents, and the chips are directly disabled after water vapour penetration.
- Some oils contain ester components that slowly soluble ABS and PVC base materials, which transform the antenna.
- High pressure hot water wash (80-90°C, 10-20bar) is a sacrificial pattern in the slaughter industry and the common encirclement process does not stand up to this combination of heat shocks + hammers.
For this type of scene, labels are usually filled with PPS or PEEK base materials with ceramics to fill the seal, and the overall protection level is IP69K. When we do a selection test for machine process-type customers, it is common practice to have samples in 80 °C oil for 720 hours, then to measure changes in reading distance, and to control decay within 15% is considered acceptable.
Metal surface: URF labels short-circuit with metal, not power.
A common misconception is that poor range on metal means the reader lacks power. UHF waves at 860–960 MHz produce strong reflections and eddy currents at metal surfaces. These detune standard tag antennas and cut range from meters to centimeters. For metal applications, heat resistance is therefore a combined requirement: the tag must withstand both high temperatures and the metal environment.
The metal environment is addressed by several routes, with trade-offs:
- Segregation: A layer of foam or plastic between labels and metals, usually 5-8 mm thick, with a read-out range that recovers but increases overall thickness.
- Special metal antennas: The printing of special pattern antennas on the back of labels allows for parallel orientation of electromagnetic fields and metal surfaces, which can be 1-2 mm thick.
- Ceramic seal: Chips are wrapped in ceramic shells, antennas are drawn from within the ceramics and are strong in temperature resistance and metal resistance but cost-effectively high.
The oven tray, metal assembly, steel roll positioning, chemical response to scenes is the second - special metal antenna + PI base, working at temperatures typically covering between -40°C and +200°C, peaking at a short time up to 250°C (depending on the product). When we test the steel industry clients in situ, it is generally recommended that suppliers produce reading curves on aluminium plates, steel plates, non-stainable steel plates, and that light be given to figures in air without reference.
A few indicators to look at when choosing a model
To abstract the three above-mentioned categories, the selection is really based on five parameters:
- Sustained working and peak temperature: Many labels of "200°C for high temperature" are actually short-term peaks, with a significant decrease in the lifetime of the chip at 180°C over a long period of time, requiring a look at the curve of the data manual rather than the number of specifications.
- Base and encapsulation materials: Directly determined chemical tolerance, PI/PPS/PEEK is much better than PET/ABS.
- Read distance on target media: Must be measured and the reference value of reading distance in air is limited, especially in the liquid environment of metals and high-media constants.
- Protection level: IP grade is of limited interest to the oil-contaminated scene, IP68 does not equal IP69K and the latter depends on high pressure wash positions.
- Cycle frequency commitment: clearly indicates how many times a disease can be sterilised, cleaned, hot cycle and conditions for testing.
Back to application itself
The three types of work, fungi, oil pollution, metal, appear to be three problems, all of which point to the same thing: in the hands of a certified supplier, label parameters are tested from end to end; in a model-selected project, tags are used to step through actual work pits. Instead of being the highest in terms of scalability, you can use your own antibicide process, clean processes, metal bottoms for measurement, and then take the data curve to the bottom. If the scene is complex or needs to be aligned, welcome contact with Shanghai-based short-tech, we can provide case-specific labelling programmes and old test data support to help you move this selection more firmly.

Ms. Lei
Mr. Pang