What are the advantages of a RFID-based fixed asset management system?
RFID is not a "high bar code": from the point of view.
The advantages of RFID asset management are understood by seeing the difference in its nature and that of traditional bar codes.
The traditional bar code (one-dimensional or two-dimensional) works in the form of optical recognition: a sweeper sends a light, sweeps into a strip area between black and white, and reflector light is decoded into numbers. This process requires that light be aligned to one reading, only one at a time.
RFID uses electromagnetic sensors: the reader antenna sends a radio frequency signal (most used in fixed asset management) and the inside antenna receives it, re-reflects the stored coded information, the whole process does not require light, no sight, no contact.
The two sets of principles bring three fundamental differences:
- Batch Read: RFID readers can read dozens to hundreds of labels per second; bar codes can only be one sweep.
- Non-ViewRFID labels can be shielded and wrapped, as long as they are read within the electromagnetic field of the reader; bar codes must be exposed and seen.
- Rewritable: The data in the RFID label can be changed repeatedly (e.g. by updating the asset's status) and the bar code printed cannot be changed.
Batch identification: From "scan-by-scan" to "sweep-in-a-scanning."
The most visible value of RFID in fixed asset management is the shift from a human to an equipment-intensive inventory.
Traditional stocktaking uses teams of two, with one person scanning each item and checking it against an Excel sheet. Ten thousand assets take one to two weeks, and those borrowed or returned during the count are easily missed or counted incorrectly.
The RFID count is completely different. Hand-held readers push through the shelf or warehouse, and in seconds to dozens of seconds they can complete a region scan, hundreds of assets are read at the same time. At one manufacturing client in Shanghai who used to do the technology for the Best Technology service, the monthly count that would have been completed in two weeks was cut half a day after the RFID went online.
The root of this change is the difference between "reading": RFID is non-contact, non-sighted, mass. In the cabinet, in the drawer, in the bottom of the shelf, labeled, through the readers, these assets are identified at the same time, and the inventory report automatically generates.
Life cycle: turning assets from "posted and unattended" to "checkable."
The real difficulty in the management of fixed assets is not at the moment when the procurement was entered, but if it is found after five or six years.
The RFID system, in conjunction with the back office asset management software, can record the entire process of entering assets from warehouse to end-of-life: every change of location, each acquisition return, every maintenance, automatic recording of time, operator and location. This data chain covers the full life cycle of the asset.
Actual benefits:
- The accuracy of the count has been significantly increased (from high error in manual inventory to close to 100 per cent reading accuracy, with specific numbers relevant to the field environment).
- The rate of asset loss has dropped significantly. Many firms are not actually losing the "failure" they reflect, but no one knows which department or floor it is in.
- End-of-life decisions are supported by data - the end-of-life determination of which equipment should be phased out through life, maintenance records and idle hours.
For financial and audit purposes, RFID collected asset data that directly cross-referenced ERP (Enterprise Resource Plan System) and the financial statements to allow reconciliations from "end of year surprise" to "ready available".
Landing is not labeled: several key components of RFID design
RFID asset management is not "a label can be used." To make it work, several projects have to be solid.
Tab Selection
Metal surfaces, liquid environments, and high temperatures affect the RFID signal.
Reader Deployment
Fixed-type readers (mounted at doors, corridors, key locations) can cover most of the scenes with handheld readers (used for active counts).
Data set-up
RFID is not an island, but it has to be connected to the enterprise’s existing ERP and financial systems so that asset data can enter the procurement process and the financial statements. If this move is not good, RFID is just a “higher inventory tool”.
In many projects, Shanghai-based Alternative Technologies found that the key to success or failure of RFID projects was often not in the hardware itself, but in the advance site survey and system integration design - part solid and much easier to follow.
How do you judge that RFID is not for you?
Not all fixed assets are worth RFID.
- Number of assets. below 500, RFID has a long return-on-investment cycle; more than 5,000, the benefits are generally clear.
- Value of assets. High-value, easy to lose, mobile equipment (medical devices, laptops, sophisticated instruments, tools) with higher priority on the RFID. Low-value, vulnerable items are more cost-effective by bar code.
- Site conditionsIndoor, metal-mounted warehouses, building assets, RFID programmes are mature and stable; open, remote, wide-range moving assets may have to be integrated with positioning techniques such as GPS, Bluetooth, etc., and the complexity of the programmes increases.
A simple measurement idea: add up the human cost of the current inventory, the cost of asset loss, the cost of audit compliance, compared to RFID hardware, software, implementation inputs. Usually in asset-intensive enterprises, costs can be recovered for two or three years.
If you match the three dimensions above, the next step is to find a supplier for site surveys and programme design — this is a step that will double back.

Ms. Lei
Mr. Pang