What are the advantages of RFID firm-up inventories? Batch recognition efficiency resolution.
How did we survive those nights when we were doing the manual inventory?
Every December, a precision manufacturer counts its fixed assets. More than 3,000 devices, instruments, and production fixtures are stacked in its offices, and finance staff check the numbers on their stickers against a printed asset list, shelf by shelf. It's an all-too-familiar situation in manufacturing: two asset lists, one scanner, and three or four finance staff on the shop floor at 8 a.m., still more than 200 entries short at 10 p.m. One detail illustrates the problem: the scanning angle for tags on cabinet sides is so poor that the cabinets have to be moved every time, and if a QR code is dirty or peeling, the number has to be copied by hand. After a week, both accountants have red eyes and the error rate is still around 3%.
The real trouble with taking stock is not "number," but "many pairs, searching again." Assets are scattered in warehouses, workshops, office areas and even out-of-house, each item being single-targeted, trigger-to-identify. RFID is the core value of this "one-on-one, one-by-one" model, breaking into "one-on-one, one-by-one" -- "one-on-one, one-by-one" -- "one-on-one, one-by-one, one-by-one" -- "one-two, one-by-one, one-by-one, one-by-one." This is the difference between it and the two-dimensional-coded count, which is the most essential of all things, and the source of the efficiency gap.
What's the big deal?
The two-dimensional code must be "see" to read, so the scanned gun and the tag need to match it, one trigger at a time. The RFID uses a radio signal, labels inside the asset's surface or shell, a reader (also known as the reader, the antenna box that sends the radio frequency signal) within a certain distance, and can communicate with multiple labels at the same time. In short: Press the read and writer in front of the shelf, the number, name, status of 50 items on this entire shelf back to the collection end, without moving anything, without being matched or considering whether the label is masked.
Speed comes from three specific actions. First,Signal parallelRFID labels are inter-crash-resistant algorithms, with a reader able to count and weight hundreds of tags in hundreds of milliseconds, and manual sweeps can only be processed in serials; second,Read from non-visual range: The label is in the inside of the metal cabinet, on the back of the shell, in a plastic box, and as long as it is not completely blocked, the inventory officer does not need to remove the asset; and third,Data AutoBaseEach time a label is read, the data is immediately posted to the local database and synchronized with the asset system. After the inventory is completed, there is little need for manual re-entry. These three are stacked together, which is what the word "volume recognition" really contains.
A set of figures that can be compared: mass recognition efficiency decompose
The efficiency is not just about "fast," but it's about the numbers. Here's a comparison, from the conventional solid-fund accounting scene, with an asset size of around 3000, in two floors plus one workshop.
| Inventory Method | Effectively recognizing speed | 3000 units timed | Personnel requirements | Typical error rate |
|---|---|---|---|---|
| Manual +QR code Scan Gun | About 30~50 units/hours/person | 3-5 working days | 4 persons | 2%~5% |
| PDA Sweep RFID Tag | About 400 ~ 800 units/hours/person | 4-8 hours | 1~2 persons | Less than 1 per cent |
| Handheld + channel RFID door (a large number of scenes) | About 1500 ~ 3,000 units/hours | 1~2 hours | 1 person | Less than 0.5 per cent |
It should be noted that these figures are influenced by several variables.Label Type• The UHF labels are the most capable of being read in bulk, with hundreds of them read one time and often used for fixed assets; and HF tags can only be read dozens at a time, suitable for single-product management.Asset material: The metal shell equipment requires a metal resistant label, and the reading distance without metal treatment may fall from 5 m to less than 0.5 m.Environmental interferenceThe industrial field with a complex electromagnetic environment, with space and power to stabilize, is in place. First these variables are ticked out, then the paper-based digitals are not being biased when looking at the project.
Besides speed, there's a lot of lost revenue.Decline in human costsFour or five finance officers were required to re-engineer a week, and the initial drive would normally be completed with RFID in one or two half days, with the remaining time used for discrepancy reconciliations and back-up. The manual hours taken to calculate a single count can be reduced to one fifth to one tenth of the original. This money is not going to last much longer than a year, especially for medium-sized and large units with tens of thousands to tens of thousands of items.
Putting the program down: a few pits to go around.
The efficiency figures are so beautiful that there are many projects to flip over when we land. From the implementation cases we've been exposed to, the following points, if not addressed in advance, will be swallowed up by a large part of the value of mass recognition.
How do you label it? It's very different.
Many people think that the RFID label is just a sticker, but position and material directly affect reading. The same cabinet, with more than 95% chance of getting positive reading, drops back and side to about 70%, and the metal closes back (with no gap) may not read directly. It is recommended that one be assigned at the asset up front.Labeling Code: Set directions, set positions, and set minimum distance to metals. It is common to place a high-density cotton liner of 3-5 mm thick. Once the norm is laid down, read stability increases significantly.
Don't buy it in the "test" phase.
The RFID device and labels are very numerous, with different frequency bands, different antennas, different power-suited scenarios vary considerably. One conservative process is to do a small POC first (that is, first in a department, several dozen assets are actually measured), record the actual recognition rate, miss reading, misreading, then determine the type and quantity of bulk purchases. First, you're recommending full-volume distribution by manufacturer, and the common result is "time saved, real failure rates are higher than sweeps." Our approach is to include POC in standard delivery processes, run data at the client site, then enter into implementation.
It's more complicated than I thought.
Reads the labels are just a series of numbers, and it is another level to see if the financial system's asset card can match the top number. The following are planned in advance: Label coding rules (recommended to keep the original asset number, avoiding double-coded); data interface (collecting end to middle table of the asset system); and differential process (granting of the disk). If you skip this step, RFID data can only stay in Excel and cannot form a closed loop.
Daily maintenance and regular inventory synchronization
RFID is not a complete solution. The labels are disabled because of ageing, external force destruction or position deviation, and it is recommended that the labels be tested for good quality on a quarterly basis, with coverage of no less than 10 per cent; at least once a full-volume count is taken every year. The rhythm is consolidated so that the value of the RFID system can be maintained over time, rather than returning to the manual count in just one or two years.
Back to the selection itself: what's worth RFID
Back to the original problem, RFID's advantage in solid inventory is not "fast" but...I'm going to take this whole thing from a one-time, one-time, to a routine that can be done on a regular basis.. The level of asset management is at two distinct levels, once a year and once a month.
If the number of assets is over 1,000, spreads across multiple regions and requires frequent audit and internal verification, the RFID batches usually return the proceeds within six months to one year; if there are only a few hundred items, point concentration, little change, two-dimensional code sweeps are enough, and hard-on RFID adds complexity. The test is simple:See how much time it takes to get a count?And these two numbers, taken together, are the true value of the RFID program.
For units that are evaluating the program, it is recommended to start with one of the most concentrated departments in pain, a warehouse, and to get the recognition rate, the drop rate, the time savings, and then decide whether to extend it to the whole unit. A run-through RFID solidity system, which can turn the count cycle from "Annual Big Action" to "Mentime Small Action," which is what it really is.

Ms. Lei
Mr. Pang