What is the RFID asset inventory program? Design element resolution
A landing RFID asset inventory program, with four cores - the RFID electronic label, a reading and writing device (with handheld terminals and fixed-readers), backstage management software, and data interface with existing ERP or asset management systems. RFID is a non-contact automatic recognition technology that uses radio frequency signals to identify target objects and to read and write data, each of which involves selection, deployment and parameter setting, following specifications to avoid most of the implementation traps.
Element 1: RFID label selection - align identification distance and asset material first
The label selection directly determines the recognition rate and inventory efficiency of the package, with two parameters being identified:
- Operating FrequencyUHF, 860-960 MHz (typically 3-8 m) reads long distances, supports group reading, suitable for warehouses, many cabinets; HF, 13.56 MHz, is short in reading distance (within 10 cm), suitable for a single fine management, such as archives, photo. Most asset count items select URHF.
- Chips and Encapsulation: Common chips are Impinj Monza series, Alien Higgs series, with storage capacity ranging from 96bit to 512bit, sufficient to write basic information such as asset number, name, date of deposit. The way you cover them is determined by paste - metal assets must be labelled as anti-metal and common plastic or wood surfaces should be labelled with soft non-dry glue.
Paste also has a specific location: Metal surface assets (such as servers, machine boxes) suggest that metal labels or non-metallic areas be placed in flat form, at least 1 cm from the edge of the metal, to avoid the signal being blocked. The pasted is followed by a writing test to confirm that reading distance and angle are expected, which is often saved, and the site is missing.
Element 2: Reading and writing equipment configuration - handheld, portals, fixed reading and writing sets by scene
The more the reading and writing equipment, the better it is, the more the whole scene is to be counted in order to balance efficiency with cost:
- Fixed ReaderA time-set inventory, typically covering a radius of 3-8 metres, is deployed on the shelf, at the entrance to the aircraft room.
- Channel doorThe two or four antennas are deployed at the entrance and exit, creating a reading and writing channel, and automatic recording of assets entering and leaving.
- Handheld Terminal: Inventory staff carry it around a room to scan. Read range is 3–5 m and battery life is at least eight hours. Suitable for mobile counts, spot checks, and locating assets flagged as exceptions.
The actual project is usually used in three types of combination: a tunnel door flow, a fixed reader to make a regional inventory, and a handheld to final review and blind zone supplement. When Shanghai-based Chetting Technologies Ltd. was working on a programme for a room customer, it used the "Clockgate plus Handheld" combination to record the equipment's entry and exit and to quickly check the accounting date.
Element 3: Backstage management software - Inventory process and permission design is central
Once hardware is in place, software is the key to bringing up the efficiency of an inventory. A complete set of RFID asset counts backstages typically contain these modules:
- Asset desk accounts: Enclose the asset number, name, classification, location, responsible person, status paragraph, the EPC code of the RFID label (electronic product code, corresponding to the tag's ID number) and the asset number one.
- Inventory TaskSupports a variety of models, including overall, compactor, responsible person, area, etc., when inventorying the system automatically compares the results of the scan with the billboard, and the difference is marked directly in red.
- Unusual treatment(b) A special recording and processing process for missing, misreading, unlabelling, damage to labels, etc., to avoid manual note-keeping by the inventory officer.
- Permissions and LogsInventory assignments are assigned by role, operational logs are complete and audits are retroactively documented.
Two lines are recommended in the inventory mode: a timed automatic count (fixed-reader run, and then sent to the administrator) and a manual periodic count (revealed monthly or quarterly handheld), which is mutually verified, and "right book but lost" in one way.
Point 4: Data interface - real access to RFID data in asset management systems
If the RFID inventory system does not connect to ERP, asset management systems, data is only an island.
- Intersection: Common WebService interface (remote call based on HTTP), database intermediate table, file import. High-level intermediate or interfaces are required for real time, only for reconciliation.
- Key fields: At least synchronize the asset number, RFID code, location, status change time, count time, inventory person. Field name specifications are aligned with ERP in advance to avoid later re-entry.
- Change SyncRevert ERP in time for new asset entry, write-off and redeployment of three types of change in status to ensure that the accounts are consistent on both sides.
Point 5: Several pits that can easily be stepped on during implementation
- The labels are not metal-resistant.: The metal surface is directly labelled as normal, with a reading distance that shrinks from 5 metres to several dozen centimetres, and the count is almost intact.
- The antenna angle and power are not being adjusted.Theoretic values and the field environment are significantly different, and it is necessary to install a physical at-site label, adjust antenna angles and launch power.
- Ignore liquid and metal masks: Warehouses with extensive metal shelving or liquids can see significant UHF signal loss. Add relay antennas if necessary or reduce the density of tags counted per zone.
- No tag written check: Some labels may fail to write when batch writing, and are posted without validation, and subsequent failure to read and screen is extremely difficult.
- The inventory process was not in placeThe inventory clerk will not use handheld, will not handle anomalies and the perfect system will not be efficient.
A complete list of programme delivery
The following minimum elements should be included in a programme to take care of a qualified RFID asset inventory:
- On-site survey report: coverage area, asset type and quantity, distribution of metals and liquids, existing network conditions.
- List of label selections: frequency, chips, containment specifications, pasting location maps.
- Equipment deployment map: fixed reading/writing, access door, handheld plaque position and antenna angle.
- Software functionality list and flowchart: take stock of tasks, anomalies, privileges settings.
- Data interface scheme: interface document, field control table, sync frequency.
- Implementation of the plan and training programme: phased access, operational manual, inventory staff training.
The programme document is written at such a level of detail that the implementation phase will be largely non-flag. If the project involves multiple floors, multiple warehouses and complex asset types, it is recommended that this list be used as an acceptance standard at the solicitation or project setting stage to reduce later decoupling.

Ms. Lei
Mr. Pang