RFID Reader How to Select: Configuration proposal for channel number, frequency segment and read distance
RFID Knowledge

RFID Reader How to Select: Configuration proposal for channel number, frequency segment and read distance

PublishedShanghai Zejie Smart Technology Co., Ltd.

What exactly is "the number of tunnels"?

Many people are being bypassed by the "4" and "8" and "16" channels when they choose. The channel here is not about how many labels read at the same time, but how many antennas it can connect.

The reader transmits RF signals and interprets responses; antenna placement determines coverage. Think of channels as antenna sockets on an amplifier. A four-channel reader accepts four antennas, each serving a separate read/write zone. RFID anti-collision, which lets the reader identify individual tags where their signals overlap, is handled by the reader chip. More channels do not necessarily mean greater concurrency.

The number of channels depends on how many independent areas you need to cover. A warehouse with four entrances and exits that each need portal counts requires at least four channels. One or two suffice for a single production station. A multichannel reader saves cabinet space and centralizes power and management, but every antenna needs separate wiring and setup. More channels than needed increase commissioning costs.

Frequency selection: HHF, HF, LF each fit for what?

The RFID frequency band directly determines the type of label, reading distance and the environment. The most used industrial and commercial scenes are those of the UHF (UHF, 860-960 MHz) and HF (HF, 13.56 MHz), the LF (low frequency, 125-134 kHz) which are found in animal earmarks and some special industrial identification.

The features of the UHF are long reading distances (typically 3-10 metres, with a direct antenna of more than 15 metres), and it can identify hundreds of labels at a time that fit warehouses, logistics, vehicles management "mass, distance" scenarios. But the UHF signal is susceptible to metal reflection, absorbent liquids, unstable in a multi-metal or water-rich environment.

HF reading distance short (generally within 10 cm), but resistant to metal, more resistant to liquid interference and supporting standard protocols such as ISO 14443/ISO 15693, can be paid, ticketing, library management, NFC close-field interaction. The HF tag costs are slightly higher, but no complex radio frequency touch is required.

LF Short distance recognition appropriate for a metal environment, such as retroactivity of steel bottles, knife-stabbing management in machine workshops, usually within 10 cm and at a slower rate.

The central question of the selection frequency is: what kind of material you identify as objects, in what environment, does it take long distances? The object is paper boxes, plastic trays, clothing, and the UHF is the preferred; the target is metal tools, liquid bottles, or needs to be identified, and the HFC is more stable.

The reading distance on the parameter table. Just look at it.

Datasheet claims of an 8 m or 12 m read range reflect standard reference conditions: the tag faces the antenna directly, the path is unobstructed, the test is in air, and radiated power is at the legal limit. In practice, range often falls to 60% of the quoted figure or lower.

Several common factors affecting reading distance:

So, when choosing a model, it is safer not to consider the maximum distance of the manufacturer as actual deployment and to leave 30%-50% of the balance in planning for the project.

Configure reference for three typical scenarios

Scene I: Warehouse exit/ batch count

Usually, you need to cover a 4-6 metre wide passage and ask for the forklift or tray to read all labels once and fortnight. The configuration is: UHF frequency, 4 channel readers, each of which is placed on both sides of the door by one pair of directed antennas. The general Circumpolarization of the direction of the antenna (a form of antenna that is not sensitive to the label's orientation) allows the label to be placed at any angle.

Scenario 2: Production workstation / item-level traceability

The space is small, for single products or small batches, and requires a stable reading without missing. It is suggested that the configuration: UHF or HF (depending on the material of the object), 2 channel readers, which are compatible with the small peri-situ antenna or flat ceiling. The read distance is 0.5 to 1.5 metres, with emphasis on triggering stability.

Scenario III: Asset management/ Tool traceability

Object is mostly a metal device or tool that requires precise positioning, without serial reading. It is suggested to configure: HF or LF (depending on the environment), 1-2 channel reader, antenna close to the reading and writing area. This range is not critical, but it is important that the boundaries of the reading and writing areas be clear.

It's a few pits that can be easily trampled when choosing.

First, just look at the maximum distance, not at the steady distance. The former is the peak of the limit, the latter is within a range that can be read with 95% confidence, and the latter is the true number that can be used in the project.

Second, ignore the match between labels and readers. Different labels of the same manufacturer may vary significantly from one reader to another; different manufacturers are more complex in combination. It is suggested that a small volume exercise be done before a bulk purchase is decided.

Third, the number of channels is blindly numerous.8 Channels, 16 are expensive readers and complex debugging. If the scene only takes 2 channels, the remaining channel is idle.

Fourth, no expansion space is reserved. Projects are often connected to a new location and scene, with the selection of models that prioritize modularization design, support subsequent extension corridors and antennas, and save considerable back-to-work costs.

A simple selection list.

  1. Clear application scenario: indoor or outdoor? Still or moving? Mass or single?
  2. Confirm frequency band: URF or HF? Corresponding frequency in accordance with local regulations?
  3. Estimating the number of antennas: how many independent reading and writing areas are needed? How big is each district?
  4. Measured physical distance: parameter tabular distance x 0.5 to 0.7 as budget value.
  5. Validate label compatibility: test the candidate reader with actual purchase of tag samples.
  6. Consider expansion: Is there a need for subsequent access and frequency change?

Once again, it's roughly 80% of the selection error.

We've been doing RFID projects for years, and we've met with a lot of customers who have taken the "range parameters" to choose, and then they find it very poorly performed when they were field-dubled. Ultimately, RFID is a strong scene-dependent device -- no point in talking out the scenario. In Shanghai-based Chetting Technology, we usually go to the environment, measure materials, run a model label, and then put up a configuration. This process of "see the field first, set the configuration," is more reliable than a simple comparison parameter table, and saves costs later.