Type elements of the rfid tag handheld and fit analysis of the operation scene
The RFID handheld type is a model that doesn't have "a table of parameters" -- and the parameter is beautiful, and it becomes a short board in an unmatched scene. It's a more prudent way to read the work scenario as what, how far, how much, how much, how much, how, at a time, to read "four things," then to pick out the type against the device parameters. We've been helping store, make, retailed down, and this idea has been less peddled.
Step 1: Break down the work scenarios
Before you pick out the model, think about the site.
- Reader: The non-dry glue label on a box, or the metal tray, or the anti-metal tag on a swinger. The medium is different, and the corresponding frequency segment and antenna are different.
- Read range: Do you just need to bring the reader up to each tag, or read an entire row of shelves from 3–5 m away?
- Environment: a temperature warehouse, a cold storage (under -25°C), or a workshop with more dust, three-proof levels and low temperature on the screen.
- Group reading or single reading: Most of the pick-up racks are read-only, and many hundreds of inventory libraries are often cleaned at a time, with significant variations in requirements for air interface protocols.
It would be much less costly to write the answer on a whiteboard and then cross-check the manufacturer's data than to send the directly requested e-mail.
Read performances should not be limited to maximum reading distance
Many product pages simply say 'up to 8 m.' That range is often measured in a lab with no interference and a single tag facing the antenna. Reflections from metal, absorption by liquids, and collisions among tags cut real-world range. A reduction of 30%–50% is common.
Three things should be more important when looking at the parameters:
- Frequency and protocol: UHF (860–960 MHz) with EPC C1G2/ISO 18000-6C is the industry standard for bulk tag reading. HF (13.56 MHz) suits short-range one-to-one uses such as tool identification and individual item traceability.
- Receiving sensitivity: The typical value is between -82 dBm and -88 dBm, with a sensitivity of 3 dB per high, which corresponds to approximately double the reading distance.
- Group reading rate: UHF can read 50-200 labels per second under a dense label scene, depending on the protocol's realization and solid version.
Before choosing the model, it is best to have the prototype run by the manufacturer to its own warehouse, simulate 50 stacks of labels and see if you can read them in 3 seconds.
Three defenses and a continuation of course, two that are the easiest to underestimate.
Three-dependency writing IP65, IP67, one difference is very large:
- IP65 can carry a gun and wash, not soak.
- IP67 Short-term impregnation 1 m deep is fine.
- The cooler operation is to pay special attention to the temperature-depression of the screen, and the normal LCD is to slow down significantly below -20°C, reinforcing IPS or OLD more reliable at low temperatures.
The drop-and-default value also depends on the number: 1.2, which is a common industry specification. If you are often to operate on steel frames of about 1.5 meters, you are advised to select the type of machine that will be tested for 1.5 metres or even 2 metres.
For battery life, retail store inspections involve about 1,000–2,000 scans a day, and 3,000–4,000 mAh is generally sufficient. Cold-chain counts may involve continuous bulk reads through a whole shift. Use a dual-battery setup of at least 6,000 mAh that supports hot swapping. Being able to change batteries without powering down is vital for round-the-clock operations.
The system is often more time-consuming than the equipment itself.
The availability of hardware is only the first step, and whether or not it can be connected to WMS (warehouse management system) or MES (manufacturing implementation system) is key to a project's real landing.
There are a few things to be sure about when choosing the model:
- Operating systems: The Android camp is the most ecologically mature, with a large majority of WMS/MES manufacturers providing corresponding SDK (software development toolkit), with short debugging cycles; Windows/CE camp maintenance costs are rising and new projects do not recommend further pits.
- Multi-module integration: whether to integrate bar code scanning (1D/2D), NFC, GPS in addition to RFID. One aircraft is lighter than the attached module and has fewer failure points.
- Data Interaction: Call the vendor SDK directly or forward through a middle. If the system is already using a Web Service or RSTful interface, it is recommended that the end-end output standard JSON or XML avoids private formats.
Integration labor typically costs one to two times as much as the equipment. Spelling it out in the contract up front avoids disputes later.
The direction of the arctics is often ignored.
UHF antenna splits polarize and circle. Linear polarized reading distance, but very directional, labels must be fixed to the antenna for reading; Circumpolarization takes a partial reading distance in the direction of tolerance, and the label can be swept from any angle.
Experienced this choice:
- Hand-sweeping boxes at the top of the shelf, which are linearly polarized and readable to a sufficient extent.
- Ground carts, pallet mixes, labeled irregularly and Circumpolarized to save attention.
- The metal surface is labelled as anti-metallic, and must be accompanied by antennas, and it is common to have normal machines that cannot be read.
The two antennas are partly supported, while some require a change of machine.
Weight and a sense of control are a matter of time and time.
The difference between 400 and 600 grams may look small, but it is noticeable after eight hours of holding a device one-handed. In the projects we reviewed, staff often rejected a model because it made their wrists ache, not because it failed to read tags.
A few details can easily be stepped on:
- Whether the trigger is a clean or not, it is difficult to exhaust the thumbs for long periods of time.
- Whether the grip is smooth or not, it is particularly important to hold gloves in the freezer.
- Whether the screen can be seen in the sun, it is useful to go out and do a physical test more than see the brightness parameters.
Before bulk purchases, a prototype was used for one week for first-line staff to hear the real feedback and then to write down a list more directly than any technical parameter.
Budget allocations, less hardware and more services
Finally, many procurement managers have gone through this curve: they have put a large budget on the purchase of equipment, debugging it, redevelopment it, and training it has been reduced.
The more rational allocation of experience is as follows:
- 50% of equipment, 60%.
- System docking with secondary development 20%-30%.
- Training and piloting 10% ~ 15%.
- Stay 5%-10% as an emergency.
When Shanghai Selecting for Technological Co. Ltd. offers its programmes to clients, it usually puts this percentage in advance of the contract and avoids the embarrassment that "hardware acceptances pass at a later stage of the project but the system cannot run" .
Several landing reminders
If you're choosing a model, then in that order, you can make a lot less of the pits:
- Write the operating scene into a list of needs for rows 4-6.
- The two or more plants were allowed to carry a sample machine to the field and recorded three data: single-reader, group reading pass, full power hours.
- and WMS/MES manufacturer confirm interfaces to put data protocols in the document.
- Lists the concerns of 3 first-line employees (weight, key button, screen resolution) and let them try for a week.
- The budget is allocated broadly at 5:3:1.5:0.5.
The RFID handheld is not a consumer electronic product, and there is no "step-in" model, but it can be selected as a real device that can run through the working life if the scene is detached, the docking path is clear and the budget structure is sound.

Ms. Lei
Mr. Pang