How to select rfid label printer: Print method, precision and point of match for labels
RFID Knowledge

How to select rfid label printer: Print method, precision and point of match for labels

PublishedShanghai Zejie Smart Technology Co., Ltd.

What's the RFID label printer gonna do?

Select the RFID label printer, not to read the brand and price, but to align it with three things: print (thermal reprint or direct heat), print precision (203 dpi or 300 dpi) and what frequency and chip protocol do you have on the RFID tag. Matching, the machine does not have "but can't read" or "read" problems.

Thermal printing and thermal. How do you choose how to print it?

The difference is direct -- the print-in-thermal labels are coloured for months, and the heat-out labels are kept at constant temperatures for several years, which is the default configuration of most industrial RFID tag machines.

The RFID labels usually carry asset numbers, product retroactive codes, batch information, which often follow the item for two to three years or more, so the industry defaults on the heat-reprinter type. If your RFID tags are only used in a short-term scenario like a delivery list, they can save carbon belts with a direct heat machine.

And by the way, the heat-reprinter must have carbon bands, carbon belts and waxed substrates, blended base, resin base, three. The RFID labels are often marked with PET and synthetic paper, which corresponds to mixed or resin-based carbon bands, and is word-resistant against scratch. Wax-based carbon belts are cheap but only for copper-coated paper.

203dpi or 300dpi. Which one is the right one?

Print resolution (dpi) determines how sharp text and barcodes look. The industry-standard 203 dpi is enough for most linear barcodes and normal text. Use 300 dpi for small characters such as serial numbers under 5 pt, high-density QR codes, or very small tags such as those used in pharmaceuticals.

A simple way of judging: if your label is less than 40 mm in width, or if you need to print a minimum character height of less than 2 mm, choose 300dpi directly; if the label is more than 50 mm, the print is normal bar code and text, 203dpi is enough. There is also a parameter that many people ignore -- the width of the header, which is usually 4 inches (about 104 mm) specification, basically covers most RFID tag applications.

The 300dpi type is usually more expensive than 203dpi and there is no need to pay for inoperable precision.

What's the difference between RFID labels and general labels?

The RFID label is a layer of "inlay" -- that's, chips and antennas -- more than the normal label. Inlay usually puts it in the middle of the tab, which consists of chips (storage data) and antennas (receiving radio frequency signals). Three things must be confirmed:

What are the key parameters to be considered in the selection process?

After printing and precision, the following are easy to ignore:

How do you verify that printers and consumables are really matched?

The parameters are right. It's still to be tested. Two things are important:

First, the reading rate.Batch printing of 100 labels, read by reader and then read out, usually with a line exceeding 95%. Below this number is either the inlay position and printer's writing antenna that is not right or the label material affects the radio frequency signal.

Second, print clarity.The standard for success is a one-dimensional first reading rate of more than 95%, and a two-dimensional level of higher than C.

And it's over, and it's true that the printer and the fuel are compatible. And in the projects we're exposed to, there's not much of a parameter that actually doesn't work -- like a retroactive manufacturer of medical devices, with a new label, which falls from 98% to 82%, and sorted out the inlay position that is a new label, which is a few millimeters away from the old tag, and the machine is not self-compensated.

When you choose, it's almost impossible to go in that order.

I'll put your needs in this order:

  1. Application of scenes (storage, retailing, medicine, fixed assets?)
  2. Label size and minimum print characters
  3. The label is used for a long time, and it determines how to print (thermal or direct heat)
  4. The material supplier brand and inlay specifications determine the scope of printer compatibility tests
  5. Day print volume determines the speed of printing and the durability of machine

If you take a match between the non-labelling protocol and the printer agreement, or you need to do compatible tests for your labels, you can talk to a supplier with RFID print-in experience. Shanghai-based Technological encountered some similar "no" questions in making RFID tag printing programs, mostly inline position and machine default parameters that were not right, but stabilized after each one.