Seal structure, test method and applicable environmental description of the anti-liquid rfid electronic label
The anti-liquid RFID labels address two things at once: the circuit itself is not subject to liquid intrusion, and the signal remains stable in the liquid environment. The choice of sealed structures, test methods and applicable environments around both points is followed.
Many people have a simple hunch: labels are water-resorted, and they're wrapped in plastic shells. The idea underestimates the effect of liquids on RFID -- water molecules strongly absorb radio frequency energy, especially ultra-high frequency bands (UHF, 860-960 MHz), liquid media constants far higher than air, and electromagnetic waves decline significantly when passing through liquids. So "waterproof" is not the same as "useable in a liquid environment," which is the key watershed for the design of the liquid RFID.
Why would the liquid interfere with the RFID signal?
First, the RF energy that reads and writes is used to connect through space to the label antenna, which uses the tag chip to work on it and to send back information. When there is a liquid gap between water molecules, high-media constant (about 80) and loss factors both reduce the electromagnetic wave range and change the transmission path -- the result is that the distance from reading and writing is significantly reduced, with the original 5m mark, which may be less than 1 m on the wall outside of the bucket. So the design core of the anti-liquid label is not simply to wrap up the circuit but to keep the antenna radiation as low as possible while sealing.
Seal structure: Three lines of thought are open and open.
The current market-resistant RFID labels are sealed in three broad categories, with different pain points and different reliability and cost.
Enrichment
We've had a scene of excessive temperature, high pressure and detergent shampoo in industrial washing projects, where the overall sealing labels have not been sealed out for two years. The disadvantage is that the thickness has decreased so softly, it is not suitable to be attached to an arc object; once the coating is broken, it can be replaced only in its entirety.
Duplicate pressure
The plastic sheet is a plastic sheet that binds inlay (in which there are thin sheets of antennas and chips) and is sealed together by thermal pressure, usually 0.5-1.5 mm thick. This label is thin enough to bend, and it fits on clothing or warp containers. But the weakness is in the seam -- if there's a small flaw on the edge of the heat pressure, long-term exposure fluids see through the seams. We have seen some cheap film tags run off dozens of times in the industrial washing machine, and most of the problems come from an uneven pressure on the edge.
Hardshell wrapping
ABS or PC shell with a seal, like a small box, labels in it. This structure is resistant to shocks, chemically corrosive, and often in the context of chemical drums, pallet recognition, etc. Shanghai-based Cheeky Way Technologies uses hard-shell containment programs when they trace barrel filling material to chemical clients, because they deal with acid and solvents in addition to water. The disadvantages of hard-shells are overweight, high cost, and antenna design avoids metal.
Test method: Not just "buffy."
At least four levels of clearance are required to determine the eligibility of an anti-liquid label.
Seal Level Test
The most common is IP-protection levels. IP67 requires 30 minutes of immersion in 1 metre of deep water; IP68 requires longer or larger water pressure (commonly configured at 3 m/24 hours or deeper). Note that, if the actual scene is a chemical liquid, it is not enough to report on the IP alone - the chemical liquid erodes sealed material and additional chemical compatibility tests are required.
Signal performance test
Insulated the label into water or placed on the outer wall of a liquid-filled container, measure reading and writing distance and RSSI (receiving signal strength indicators). A qualified anti-liquid label should not be reduced by more than 30% to 40% in a dry environment. More than 50% of this is used in cases where "frequently read."
Temperature cycle combined impregnation test
Thermal cycling commonly causes seals to fail. Repeated expansion and contraction can produce hairline cracks. Typically, tags go through dozens of cycles in a chamber between -20°C and +85°C before immersion testing. This combination better reflects real conditions than immersion alone, since industrial laundering and cold-chain transport can involve significant temperature swings.
Long-term impregnation and ageing tests
Some of the scenes need to be labelled in liquid for months or even longer, like chemical storage, long-term underwater monitoring. It is recommended that 30 days, 90 days or 180 days of immersion ageing be performed, and that we regularly take out a check on signals and appearance. We have encountered a label with short-term bubble water, but three months later there's a slight whiteness in the laminate, and the signal starts drifting -- this is how material has a chronic resistance to fluid.
Applicable environment: selected by "liquid type + temperature condition"
Industrial washing and textiles
The detergent is mostly a weak alkalin or acidic liquid, at temperatures of 60-90°C and subject to centrifugal dehydration.
Food processing and slaughter
The environment is wet and has blood and fat, and it also has to be able to handle high temperature steam cleaning (up to 121°C) and chemical disinfectants.
Chemical storage and transport
The temperature changes are significant in the case of liquids of many types (acid, alkaline, solvent, oil).
Outdoor and cold chains
Rainwater, condensation and low temperatures are the main challenges. The wide temperature work range (-40°C to +85°C) above IP67 is basic configuration, with either a membrane or a laminate, focusing on whether antenna design can still work at low temperatures.
Medical and laboratory
The re-sterilisation (alcohol, sodium hypochlorate, hydrogen peroxide etc.) is required, and some of the scenes are also resistant to high pressure sterilization.
The three questions that are suggested before the selection are answered: What is the liquid composition? What is the temperature range? Need for softness or rigidity?

Ms. Lei
Mr. Pang