How does RFID technology work in asset management?
The key thing about RFID's asset management is: don't label it as if it was a "manipulated asset." What really works is to put the tag coding rules, a network of readers, an inventory of processes and back-office systems together. A good project can reduce the count efficiency from a few days to two hours, and the difference in the accounts from a few percent to a thousand. And let's get this straight.
Element 1: Set the frequency and label type first
RFID has low-frequency, high-frequency, UHF three types of use that vary widely, and mixing can easily cause problems.
- Low frequency (125-134KHz)The tools and moulds are much more useful.
- HF (13.56 MHz)The range of 10 cm to 1 m is used.
- UHF (860-960 MHz)The reading distance can be 3 to 10 metres, and it identifies hundreds of labels at a time. It is the preferred of large asset inventories such as warehouses, shelves, vehicles. But there are more obvious interferences with metals and liquids.
Three questions first: What are the materials of assets? How many do you read at a time? How far do you read them? The answer is clear, and the frequency is set.
Element 2: Label coding rules are designed for one-time
Many items return to the code. The code is confused and the back-office system cannot be cleaned.
- It is proposed to use a three-part structure of "Project Code+Asset Category+Flowwater" such as "SH-01-000123", with a length control between 16 and 24 places, taking into account capacity and efficiency.
- synchronises three fields for writing: the name of the asset, the date of purchase, the custodian. The three messages are not available on the system or on the handheld terminal.
- The uniqueness check of the code must be pre-set, cross-referenced to existing databases before writing and avoid duplication.
- The label storage area is proposed to be divided into three blocks: the EPC block coding, the User section containing custom data and the TID area only. Subsequent forgery prevention and life-cycle traceability are mainly based on TID.
Point 3: The rewrite and antennas cannot be deployed "on top"
The deployment is to be carried out in a manner that takes into account both coverage, blind areas and interference.
- Warehouse scene: A directional antenna is installed at both end and middle of the shelf, with a width control of 3 to 5 metres and an accuracy reading can stabilize above 99 per cent.
- Office scene: Offices with dense assets such as desks, chairs, and laptops should use circularly polarized antennas with a 2–3 W reader. Limit range to 1–2 m to avoid reading assets at neighboring workstations.
- Metal environment: Choose tags with an on-metal layer. Standard tags attached to metal lose more than 60% of their read range.
- Communications Selection: fixed point points more stable by net; mobile handhelds walk WiFi or 4G.
During a warehouse rollout, engineers from Shanghai Zejie Technology Co., Ltd. recommended placing a four-channel reader at each end of every aisle. This let staff cover a full row in a single pass with a handheld reader instead of walking back and forth. In operation, the stocktake fell from two shifts to three hours.
Element 4: The inventory process needs to be put into action
Good hardware, no process, no clean.
- Periodical slottingMonthly inventory of precious assets, quarterly inventory of general equipment, six months of low-value, deplete life and three separate tranches.
- Path Planning- To draw a route by warehouse or floor, and to set the time of stay at each point (normally 3-5 seconds), so as not to pass and forget.
- Unusual on-site registration: When labels are read but not recorded in the system, or if they are not read on site, both cases are registered on-site and differences cannot be consolidated until the end of the month.
- Monthly redisk: Discrepancies are pulled at the end of each month, with an analysis of tags de-listed, code errors or changes in asset location, corresponding to improvements.
At one manufacturer, we replaced a full-day plant shutdown for stocktaking with small daily counts and a full monthly count. Staffing fell 70%, and discrepancies dropped from 4.2% to 0.6%.
Element 5: Unusual processing and data governance should be targeted over a long period of time
In daily operations, data is more important than full labelling.
- Tabs OffMetal surfaces suggest a re-energizing of nails or back-fold + epoxy resin; labels that are not readable for two months are directly on the list to be repaired.
- Error: a barrier between adjacent corridors or floors, or a lower reading/writing power of 1 to 2 dB at the expense of a distance for precision.
- Data SyncHandheld inventory results are sent back to the system in real or quasi real time, and no mass import is expected until all counts are completed, otherwise changes in intermediate assets will flush out the difference.
- System dockingRFID intermediates support the SPI interface, which facilitates access to ERP and EAM systems. The Shanghai-style alternative RFID asset management program has standardized this area, with little need for secondary development of the interfacing mainstream management system.
End
The RFID asset management is not a one-time project, but an ongoing operation. The hardware selection, code code code, deployment density, the inventory process are done, and it's easy to get down from a few percent to a thousand. It's better to start with a specific scene, starting with a warehouse or a workshop, before going through the process and then going to the whole plant.

Ms. Lei
Mr. Pang