How do you select the rfid electronic tag handheld terminal, and the function and frequency segment configuration is analyzed?
What should RFID look at when he holds a terminal?
Select the RFID handheld terminal, with two hard indicators: frequency bands and reading/writing distance. UHF(860-960MHz) is suitable for long-range mass reading, warehouse count, logistics tracking is mostly used this; HF (13.56 MHz) is appropriate for close-distance precision reading, door prohibition, ticket cards, small case management; LF(125kHz) is now less useful, mainly in animal identification and some industrial scenes. And there are handheld machines that support double-frequency, even triple frequency, with a budget, and a lot of scenes to consider. After reading distance, the protocol supports, the level of protection is set, and then the brand and price are not going to go off.
Where are the differences between the three bands of UHF, HF and LF?
The frequency is a direct decision on whether you can and can.
UHF UHF: main mass-reading power from remote
The UHF band runs from 860 to 960 MHz. Typical range is 3–10 m, and an external antenna can extend it. UHF quickly reads dozens or hundreds of tags at once and is used for warehouse inventory, asset audits, and production line tracking. Metal and liquids interfere significantly, so use on-metal tags or optimize antenna placement in those environments. The mainstream protocol is EPC Class 1 Gen 2 (ISO 18000-63).
HF HF: close and precise interaction
The HF frequency is 13.56 MHz, which reads within a normal distance of 10 cm, but is more resistant to metal and liquid interference than the UHF, and is suitable for accurate reading and writing. Payment, membership cards, book management, loaning tools, medical devices are basically used for the tracking of these scenes. The NFC and ISO 14443, ISO 15693 are most common in protocols, if you have labels or cards that meet both criteria, compatibility is almost no problem.
LF Low Frequency: Special scenes
LF is about 125 kHz, with a reading distance of just a few centimetres, but it's very permeable, almost free from metal fluids, so animal earmarks, car key sensors, and some industrial current lines are still in use. This frequency is getting smaller in the civil RFID project, and you can check the label type before you choose.
How do you choose reading and writing distance and antenna design except for frequency bands?
Read-and-write distance is not just a nominal parameter, but is judged in relation to the actual scene.
First, look at label sizes and materials. Same UHF labels, with a small metal-resistant reading distance of maybe 1-2 meters, can reach 8-10 meters on average. The handheld must be measured by the label you actually use, not just by the limit of the plant's promotion.
Second, look at the type of antenna. The inside antenna is portable and suitable for moving the disc; the outer handler antenna is more remote and directed, and suitable for asset scanning in high places on the shelf. Some support antenna replacements, which are more flexible.
And third, look at the group reading. If you have to sweep a tray at a time in a warehouse, it's important that the mass reading rate and collision-proof algorithms are available. The EPC Gen2 protocol itself has a collision-resistant mechanism, but there are very different actual performances of different chip programs, so that a lot of tests can see the true level.
Protection levels and re-entry, why is it so easy to ignore?
The industrial site is carrying a RFID handheld, IP protection level and batteries are two hidden formations.
The protection level is at least IP54, which means that it's dustproof and all parties spray. Warehouses, workshops, outdoor environments are common for ash, water spilling, and even short-term showers, and below IP54 can barely last six months. If this is a site, a freezer, an outdoor inspection of the bad environment, it is recommended to go directly to IP65 or IP67, and the drop indicator is 1.5 metres or more.
Battery life depends on daily workload. For ordinary stocktaking, 4,000–5,000 mAh is good for about eight hours. Sustained HF tag scanning or an external UHF module drains it faster; choose 6,000 mAh or more, or a model with a replaceable battery. Fast charging and USB-C are now nearly standard. Avoid old Mini-USB models.
Systems and extensions, should we consider?
The extension of the operating systems and interfaces directly affects the later use costs.
On the system, Android is the mainstream, applied eco-rich, developed fast; Windows Iot has a stock of some industrial scenes, but new projects are becoming smaller. If your upboard system is an ERP or WMS enterprise, make sure that the handheld can run the corresponding App or SDK in advance.
For interfaces, 4G/5G, Wi-Fi 6, Bluetooth 5.0 is basically a stylish and USB Type-C and OCG functions are common. External scans, fingerprint modules or printer settings are required to confirm whether there is a GPS or serial extension.
One more thing is easy to ignore: data security. The national GB/T 39786 has password-compliant requirements for RFID systems involving sensitive data, and if your project involves personal identity, asset desk account, this type of information, it is best to choose the type that supports state secret algorithms or hardware encryption.
What are the key messages that need to be identified before procurement takes place?
Clear scenes and technical parameters are first set, with fewer curves.
- What frequency bands? What's the number?
- How many labels do you need to sweep one time? How much distance does it take?
- Working environment: indoor or outdoor? Is there any metal fluid interference?
- Time of use per day: How long is it going to be? Should we change the battery?
- What's the upper system? Is there an off-the-shelf interface?
- Budget scope and number of purchases?
These questions are clearly understood, and it is much more efficient to communicate with suppliers. We usually ask the client to answer this list before we do a program for our clients, and the parameters are sent back in a way that basically produces a matching machine, without having to go back and forth.
Practical recommendations: test and bulk procurement
No matter how much the parameters look, you have to take a sample. You've got to take your own labels, test reading distance in real settings, read speed, resist interference, record data from different environments. The problem at the sample stage is far more than bulk purchasing shows.
An automotive parts warehouse we worked with initially chose a standard UHF handheld reader. Once it was tested among the metal racks, the read range fell from 8 m to less than 1 m. Switching to on-metal tags with a high-power external antenna resolved the problem. An early site test would have caught it.
Ask about after-sales service and firmware upgrades. RFID handhelds are commonly used for three to five years. Firmware update frequency, repair response time, and spare parts availability matter over that lifespan.

Ms. Lei
Mr. Pang